- USR-TC - mailman.xmission.com

Re: [USR-TC] Total Control 1000 Using T1 modem with E1 PRI lines
by Alexander Jaliashvili 29 Aug '03

29 Aug '03

Not possible. > Please help with this. > I am new with TC. > > It is possible to use E1 PRI lines with TC 1000 when I have T1 modems. > > I have this configuration: > 5 3Com High-Density 24 Channel DSP (120 lines) > 5 3Com T1/E1 HDM DSP NIC's > 2 Hiper Acces Router Card > 1 Hiper NMC > 2 AC PSU 130 AMP Nac > 1 10/100 NMC NIC > 2 Dual 10/100 PCI Ethernet NIC > > Can I address the 24 modems in the T1 DSP to make it work with the E1s? > > Something like use 4 E1s (120 lines) map the 5 T1 modem cards (120 modems). > > Thank you for your help. > Jaime > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

2 1

Total Control 1000 Using T1 modem with E1 PRI lines
by RComSA - Jaime A Roldan 28 Aug '03

28 Aug '03

Please help with this. I am new with TC. It is possible to use E1 PRI lines with TC 1000 when I have T1 modems. I have this configuration: 5 3Com High-Density 24 Channel DSP (120 lines) 5 3Com T1/E1 HDM DSP NIC's 2 Hiper Acces Router Card 1 Hiper NMC 2 AC PSU 130 AMP Nac 1 10/100 NMC NIC 2 Dual 10/100 PCI Ethernet NIC Can I address the 24 modems in the T1 DSP to make it work with the E1s? Something like use 4 E1s (120 lines) map the 5 T1 modem cards (120 modems). Thank you for your help. Jaime

1 0

RE: [USR-TC] Sorry, another test
by Joel - Fox Computers 28 Aug '03

28 Aug '03

Thanks - at least I'm getting them again! Cool! -----Original Message----- From: Oliver Francke [mailto:Oliver.Francke@telefonica.de] Sent: Thursday, August 28, 2003 12:47 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] Sorry, another test On Thu, Aug 28, 2003 at 12:43:02PM -0500, Joel - Fox Computers wrote: > Wasn't getting list emails, think I got it fixed, gotta try one last time. > > Sorry. Well, I think this is a test for *all* on this pretty quiet list ;-) Oliver. > > Joel > > > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc -- Oliver.Francke(a)telefonica.de fon. +49-5246-80-1389 mob. +49-171-5597734 I used to have a sig, but I've stopped smoking. _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

Sorry, another test
by Joel - Fox Computers 28 Aug '03

28 Aug '03

Wasn't getting list emails, think I got it fixed, gotta try one last time. Sorry. Joel

2 1

SNMP and MRTG
by Vincent Jordan 28 Aug '03

28 Aug '03

I have a couple old USR TC ( 500 I think ) Net server is version 3.8.1 I believe. Ive found a lot of info on the hyper arc and hyper dsp but can not seem to find any info on this older stuff. I would like to monitor temp, connected users / lines available, warn me if a line were to go busy out for any reason, and any other diagnostic info I can monitor. Thanks in advance Vincent Jordan Network Operations Cyberspeed Internet ( www.cyberspeed.us ) Cyberspeed Data Center ( www.cyberspeed-data.com ) Tel: 814-539-4625 Fax 814-539-4681 Email vjordan(a)cyberspeed-data.com Cellular 814-525-2359 Nextel Direct Connect 189*100*703

1 0

Hello?
by Joel - Fox Computers 28 Aug '03

28 Aug '03

Is this list still alive?

3 2

radius problem
by shahrooz 28 Aug '03

28 Aug '03

Hi all, I have a problem with on interaction of TC (with a netserver card) and radius server and that is: when user credit is finished, TC does not disconnect him on that session (Of course user will not be authenticated next time he dials in). Could anybody advise what is the solution? Is it related to SNMP and any special setting?(or MIBs); does it need a Kill Script on radius server? I have this problem with Windows-based radius servers and not with Linux-based radius servers. Thanks for your comments and advises. Kind regards, Shahrooz

2 1

RE: [USR-TC] Total Control manager
by Kirti S. Bajwa 26 Aug '03

26 Aug '03

Alex: I think you are right. I have Win NT 4.? Sitting in front of all local PC as a Proxy Server. You have given me good hint. I will put it on the post if I figure out what to do? Thanks again. Kirt -----Original Message----- From: alex [mailto:alex@wanex.ge] Sent: Tuesday, August 26, 2003 9:04 AM To: Discussion relating to the 3Com/US Robotics Total Control modem systems. Subject: Re: [USR-TC] Total Control manager Kirti, I can access your TC too. It may be your network problem. Are you sure that none of your equipment is blocking snmp activity? P.S. Its better to change community strings of NMC for security reasons (now whole forum knows your read and write communities). Kirti S. Bajwa wrote: >Just to add something. I looked into the \3commapps\tcm\devdb directory. >There is only one file "chsindex.idb", which I have attached. > >I opened this file using NOTEPAD. It has only two lines of data as follows: > >[Chassis DB] >Status=Current > >It is all new to me so I can not tell if something is missing or not? > >Kirt > >------------------------------------------------------------------ > > > > >Thank You.. Thank You.. > >Attached is the file you asked for. > >Kirt > >-----Original Message----- >From: ISN Support Staff [mailto:support@isn.net] >Sent: Monday, August 25, 2003 8:12 PM >To: Kirti S. Bajwa >Cc: 'Discussion "relating to the 3Com/US Robotics Total Control modem >""systems.' >Subject: RE: [USR-TC] Total Control manager > >Hmmm, this is an odd one... Can you send me the files in your >\3commapps\tcm\devdb directory? They have all your connection settings, >so I can see if it's possibly just a wrong option selected or >something. You shouldn't have any problem running TCM on any recent >Windows operating system. I've run TCM 8 on Win98, WinXP, WinNT4, and >even Linux under Wine. > > >On Mon, 2003-08-25 at 21:06, Kirti S. Bajwa wrote: > > >>I just displayed the TCM Version. It is 8.2.6 >> >>If you can connect it, why can not I? >> >>Thinking that my TCM installation is bad, I reinstalled TCM on the Win NT >>4.? Server. No luck. Same error. >> >>I have also tried installing the software on a Win XP PRO PC. Same Error. >> >>Is it possible that I need to have a stand alone PC? Can I run TCM >> >> >software > > >>on a stand alone PC with Win XP Home or it has to be Win 98? >> >>Any suggestion is highly appreciated. I am getting frustrated. This is my >>first encounter with 3ComTC. >> >>Please respond!!!! >> >>Kirt >> >> >> >>-----Original Message----- >>From: ISN Support Staff [mailto:support@isn.net] >>Sent: Monday, August 25, 2003 5:19 PM >>To: Discussion "relating to the 3Com/US Robotics Total Control modem >>systems. >>Cc: Kirti S. Bajwa >>Subject: RE: [USR-TC] Total Control manager >> >>Hi Kirti, >> >> I just tried, and I'm able to connect to your system fine with TCM >>8.2.6 and the IP/communities you posted earlier. Are you using TCM 8, >>or TCM 4? I'm not entirely sure if TCM 4 will work with a Hiper system, >>so that *may* be the problem. >> >> >>On Mon, 2003-08-25 at 18:12, Kirti S. Bajwa wrote: >> >> >>>Hello Again: >>> >>>Vinny: >>> >>>I tried your suggestion. Still no progress. Same Error. >>> >>>Anybody else has a suggestion??? >>> >>>Thanks in advance. >>> >>>Kirt >>> >>> >>>-----Original Message----- >>>From: Vincent Jordan [mailto:vjordan@cyberspeed-data.com] >>>Sent: Monday, August 25, 2003 4:53 PM >>>To: 'Discussion relating to the 3Com/US Robotics Total Control >>>modemsystems.' >>>Subject: RE: [USR-TC] Total Control manager >>> >>>Do the following: >>> >>> >>>Console into the NMC with hyper terminal >>> >>>Press 1 configuration >>>Press 8 reinitialize authorize access list >>> >>>The try to open with the TCM >>> >>>Hope this helps >>> >>> >>> >>>Vinny >>>-----Original Message----- >>>From: usr-tc-bounces(a)mailman.xmission.com >>>[mailto:usr-tc-bounces@mailman.xmission.com] On Behalf Of Kirti S. Bajwa >>>Sent: Monday, August 25, 2003 4:40 PM >>>To: 'alex'; Kirti S. Bajwa; 'support(a)isn.net'; >>> >>> >>'usr-tc(a)mailman.xmission.com' >> >> >>>Subject: RE: [USR-TC] Total Control manager >>> >>>Hello Alex & ??: >>> >>>I have followed both of your advice, by performing the following steps >>> >>> >>(O/S >> >> >>>is Win NT 4.?): >>> >>>1. Setup HiPer NMC (Hyper Terminal) >>>. Setup IP address (63.113.255.9) >>>. Setup Netmask (255.255.255.0) >>>. Setup Gateway Address (63.113.255.1 => I assume this is the IP address >>> >>> >>of >> >> >>>my CISCO 26?? Router) >>>. Change Community Settings (tibp for Public & tibr for Private) >>>. Save in NVRAM >>>. Reset Hiper NMC >>> >>>2. Run TCM >>>. Open a new chassis under name TIB-TC1 >>>. Target Host 63.113.255.9 >>>. SMTP Community Setting >>>a. Read Only: tibp >>>b. Read+Write: tibr >>>c. OK >>> >>>I have done it half a dozen time and receive the same error message: >>> >>> TIB-TC1 >>> Device not responding >>> Refer to the troubleshooting section of the user guide >>> >>>For your information, I can PING the NMC & Gateway ( 63.113.255.9 & >>>63.113.255.1 )!!! >>> >>>Do you think that Win NT 4.? May be the problem? HELP.. I am going >>> >>> >crazy!! > > >>>Kirt >>> >>> >>> >>> >>> >>>-----Original Message----- >>>From: alex [mailto:alex@wanex.ge] >>>Sent: Monday, August 25, 2003 4:08 PM >>>To: kbajwa(a)tib.com >>>Subject: Re: [USR-TC] Total Control manager >>> >>>Set up NMC card: put IP address and netmask, gateway address. Change >>>commuity strings. Then connect NMC to LAN. >>>Run TCM. Open a new chassis (or smth. like this), write NMCs IP address >>> >>> >>and >> >> >>>read/write community strings. >>>Thats all. >>>----- Original Message ----- >>>From: Kirti S. Bajwa >>>To: 'usr-tc(a)mailman.xmission.com' >>>Sent: Monday, August 25, 2003 3:20 AM >>>Subject: [USR-TC] Total Control manager >>> >>>Hello List: >>> >>>My question will prove that I am below being NOVICE regarding 3Com TC. >>> >>>I have read about 10-12 different documents. I can connect and configure >>>various cards on the 3Com TC box using a serial connection to a Win NT >>> >>> >PC. > > >>>My problem is that I have not been able to figure out how to start the >>>"Total Control Manager for Windows" application? Can somebody direct me >>> >>> >to > > >>a >> >> >>>document or explain how I can launch TCM? >>> >>>Thanks. >>> >>>Kirt Bajwa >>>TIB Computer Systems >>>Mountain City, TN 37683 >>>Tel: (423) 727-3001 >>>eMail: kbajwa(a)tib.com >>> >>> >>>_______________________________________________ >>>USR-TC mailing list >>>USR-TC(a)mailman.xmission.com >>>http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc >>> >>> >>>_______________________________________________ >>>USR-TC mailing list >>>USR-TC(a)mailman.xmission.com >>>http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc >>> >>>_______________________________________________ >>>USR-TC mailing list >>>USR-TC(a)mailman.xmission.com >>>http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc >>> >>> >>> > > > >------------------------------------------------------------------------ > >_______________________________________________ >USR-TC mailing list >USR-TC(a)mailman.xmission.com >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > -- alex, ICQ# 219089461, Current status

1 0

Permanent Static Route on Netserver
by Todd Williams 26 Aug '03

26 Aug '03

Hello, Hopefully this is not a stupid question... Is there any way to add a permanent static route on a Netserver? If so, does it survive a reboot? Thanks in advance for any assistance, Todd

3 2

RE: [USR-TC] Total Control manager
by Kirti S. Bajwa 26 Aug '03

26 Aug '03

Just to add something. I looked into the \3commapps\tcm\devdb directory. There is only one file "chsindex.idb", which I have attached. I opened this file using NOTEPAD. It has only two lines of data as follows: [Chassis DB] Status=Current It is all new to me so I can not tell if something is missing or not? Kirt ------------------------------------------------------------------ Thank You.. Thank You.. Attached is the file you asked for. Kirt -----Original Message----- From: ISN Support Staff [mailto:support@isn.net] Sent: Monday, August 25, 2003 8:12 PM To: Kirti S. Bajwa Cc: 'Discussion "relating to the 3Com/US Robotics Total Control modem ""systems.' Subject: RE: [USR-TC] Total Control manager Hmmm, this is an odd one... Can you send me the files in your \3commapps\tcm\devdb directory? They have all your connection settings, so I can see if it's possibly just a wrong option selected or something. You shouldn't have any problem running TCM on any recent Windows operating system. I've run TCM 8 on Win98, WinXP, WinNT4, and even Linux under Wine. On Mon, 2003-08-25 at 21:06, Kirti S. Bajwa wrote: > I just displayed the TCM Version. It is 8.2.6 > > If you can connect it, why can not I? > > Thinking that my TCM installation is bad, I reinstalled TCM on the Win NT > 4.? Server. No luck. Same error. > > I have also tried installing the software on a Win XP PRO PC. Same Error. > > Is it possible that I need to have a stand alone PC? Can I run TCM software > on a stand alone PC with Win XP Home or it has to be Win 98? > > Any suggestion is highly appreciated. I am getting frustrated. This is my > first encounter with 3ComTC. > > Please respond!!!! > > Kirt > > > > -----Original Message----- > From: ISN Support Staff [mailto:support@isn.net] > Sent: Monday, August 25, 2003 5:19 PM > To: Discussion "relating to the 3Com/US Robotics Total Control modem > systems. > Cc: Kirti S. Bajwa > Subject: RE: [USR-TC] Total Control manager > > Hi Kirti, > > I just tried, and I'm able to connect to your system fine with TCM > 8.2.6 and the IP/communities you posted earlier. Are you using TCM 8, > or TCM 4? I'm not entirely sure if TCM 4 will work with a Hiper system, > so that *may* be the problem. > > > On Mon, 2003-08-25 at 18:12, Kirti S. Bajwa wrote: > > Hello Again: > > > > Vinny: > > > > I tried your suggestion. Still no progress. Same Error. > > > > Anybody else has a suggestion??? > > > > Thanks in advance. > > > > Kirt > > > > > > -----Original Message----- > > From: Vincent Jordan [mailto:vjordan@cyberspeed-data.com] > > Sent: Monday, August 25, 2003 4:53 PM > > To: 'Discussion relating to the 3Com/US Robotics Total Control > > modemsystems.' > > Subject: RE: [USR-TC] Total Control manager > > > > Do the following: > > > > > > Console into the NMC with hyper terminal > > > > Press 1 configuration > > Press 8 reinitialize authorize access list > > > > The try to open with the TCM > > > > Hope this helps > > > > > > > > Vinny > > -----Original Message----- > > From: usr-tc-bounces(a)mailman.xmission.com > > [mailto:usr-tc-bounces@mailman.xmission.com] On Behalf Of Kirti S. Bajwa > > Sent: Monday, August 25, 2003 4:40 PM > > To: 'alex'; Kirti S. Bajwa; 'support(a)isn.net'; > 'usr-tc(a)mailman.xmission.com' > > Subject: RE: [USR-TC] Total Control manager > > > > Hello Alex & ??: > > > > I have followed both of your advice, by performing the following steps > (O/S > > is Win NT 4.?): > > > > 1. Setup HiPer NMC (Hyper Terminal) > > . Setup IP address (63.113.255.9) > > . Setup Netmask (255.255.255.0) > > . Setup Gateway Address (63.113.255.1 => I assume this is the IP address > of > > my CISCO 26?? Router) > > . Change Community Settings (tibp for Public & tibr for Private) > > . Save in NVRAM > > . Reset Hiper NMC > > > > 2. Run TCM > > . Open a new chassis under name TIB-TC1 > > . Target Host 63.113.255.9 > > . SMTP Community Setting > > a. Read Only: tibp > > b. Read+Write: tibr > > c. OK > > > > I have done it half a dozen time and receive the same error message: > > > > TIB-TC1 > > Device not responding > > Refer to the troubleshooting section of the user guide > > > > For your information, I can PING the NMC & Gateway ( 63.113.255.9 & > > 63.113.255.1 )!!! > > > > Do you think that Win NT 4.? May be the problem? HELP.. I am going crazy!! > > > > Kirt > > > > > > > > > > > > -----Original Message----- > > From: alex [mailto:alex@wanex.ge] > > Sent: Monday, August 25, 2003 4:08 PM > > To: kbajwa(a)tib.com > > Subject: Re: [USR-TC] Total Control manager > > > > Set up NMC card: put IP address and netmask, gateway address. Change > > commuity strings. Then connect NMC to LAN. > > Run TCM. Open a new chassis (or smth. like this), write NMCs IP address > and > > read/write community strings. > > Thats all. > > ----- Original Message ----- > > From: Kirti S. Bajwa > > To: 'usr-tc(a)mailman.xmission.com' > > Sent: Monday, August 25, 2003 3:20 AM > > Subject: [USR-TC] Total Control manager > > > > Hello List: > > > > My question will prove that I am below being NOVICE regarding 3Com TC. > > > > I have read about 10-12 different documents. I can connect and configure > > various cards on the 3Com TC box using a serial connection to a Win NT PC. > > My problem is that I have not been able to figure out how to start the > > "Total Control Manager for Windows" application? Can somebody direct me to > a > > document or explain how I can launch TCM? > > > > Thanks. > > > > Kirt Bajwa > > TIB Computer Systems > > Mountain City, TN 37683 > > Tel: (423) 727-3001 > > eMail: kbajwa(a)tib.com > > > > > > _______________________________________________ > > USR-TC mailing list > > USR-TC(a)mailman.xmission.com > > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > > > > _______________________________________________ > > USR-TC mailing list > > USR-TC(a)mailman.xmission.com > > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > > _______________________________________________ > > USR-TC mailing list > > USR-TC(a)mailman.xmission.com > > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > >

2 1