February 2003 - montgomery_boats - mailman.xmission.com

Re: M_Boats: Spinnaker questions
by chbenneck＠juno.com 10 Feb '03

10 Feb '03

Hi Steve, I had a spinnaker on my big boat and sailing just with my wife, I investigated the sock to tame the spinnaker. The idea is simple: you hoist the spinnaker in the sock. Then when the spinnaker is hoisted, you pull on the UP line that pulls the sock up from the bottom of the spinnaker allowing the spinnaker to fill and fly. When it's time to douse the spinnaker, you pull on the DOWN line, and pull the sock down over the spinnaker: collapsing it into the sock as the sock comes down. (The control lines are an up haul and a down haul) When the sock is all the way down, the spinnaker is back in the sock tube, and all is peaceful and serene. One problem you have flying a spinnaker is that you are running down wind. If the wind speed picks up, you hardly notice it (remember it's wind speed minus boat speed) so you will tend to carry the spinnaker far too long as the wind builds. In my case, we were heading for Buzzards Bay, spinnaker was up and pulling beautifully; when I slowly started noticing that the bow wave was almost coming up to deck level. HUH? What's going on? .......and it was only then that I recognized that it was HIGH time to get the spinnaker down .................... So, be aware, going downwind with a spinnaker can be deceptive for the skipper. Magazines like SAIL and CRUISING have had articles on handling a spinnaker, so if you have access to a good library check out if they have them. Connie

1 0

Spinnaker questions
by Harvey Wilson 10 Feb '03

10 Feb '03

Hi Steve.. There's a book out called "Spinnaker Handling" by Bent Aarre (correct spelling). Like you, I have a spinnaker for my M-17, but never have used it. Now that I'm retired, I'll try it when the weather gets warmer<GG> Regards, Harvey/ Ga M-17 Stargazer #294

1 0

M15 Spin size
by Doug Kelch 10 Feb '03

10 Feb '03

Does anyone have the measurements for an M15 Spinnaker? Thanks Doug Kelch __________________________________________________ Do you Yahoo!? Yahoo! Mail Plus - Powerful. Affordable. Sign up now. http://mailplus.yahoo.com

1 0

Re: montgomery_boats digest, Vol 1 #530 - 9 msgs
by JERRYGMAY＠aol.com 06 Feb '03

06 Feb '03

I have had so many request I will l ist some of the equipment on M17 #231 all is in good condition one of the three head sails will need some minor reaipr I got in a 40 knot and I had a harken furler that was not as strong as the rest of the boat. Main has stain on it not bad, inside is in good cond., sleeps 3 very good friends, 4 hp evanrude 50 hrs on the engine, all rigging is in good shape trailor is good cond, tires good, main cover jib cover motor cover all blue good cond, I will sell the Nisson 5hp for stroke for an extra $1000.00, always in water new bottom I just could not talk my wife into keeping two boats I bought a Catilina 30 with a diesel in Sept. I really thinks the little M17 is abetter boat but let me try this C30 for a while this is my third m17 all have been wonderful. I live in southeast Texas near Beaumont, Texas. $2500.00 is much to low but that is what i paid for it threee years ago. and that is what I said I would sell it for. I had no idea the response would be so great.I did sail off shore some. I will put some pics on if some one will tell me how. I have a digital camera.Jerry May

1 0

Halyard Blocks
by Honshells 06 Feb '03

06 Feb '03

I'll condense what I wrote below. Basically, I'd like to know where I should position a furler-cover (that will be a "sock", raised up the furling) halyard block and a topping lift block. Thanks! ----- Original Message ----- From: Honshells To: montgomery_boats(a)mailman.xmission.com Sent: Monday, August 02, 1999 3:33 PM Subject: Questions on M15 rigging - Bent bolt Doug, I know you didn't want to start a discussion on the misplaced block, but that's where my sailmaker suggested I position one for a "CGI Sock" halyard: For reasons I won't go into, I did not have UV protectant sewn into my genoa when I had it mounted on a Flexible Furler last season, but had a "foresail cover" ("CGI Sock") made that will be lifted to its full height using a block somewhere up there on the masthead. Also, my sailmaker recommended a similar position for a topping lift block on the back of the masthead. Any thoughts anyone? Thanks, Craig ----- Original Message ----- From: Doug King To: montgomery_boats(a)mailman.xmission.com Sent: Tuesday, February 04, 2003 1:16 AM Subject: Questions on M15 rigging - Bent bolt This may or may not help, but for what it's worth, I've put up a photo of the M-17 masthead that Howard Audsley sent in earlier for a different purpose. Having never seen an M-15, I don't know if it's the same. If so, maybe Jerry could refer to it and see if the forestay is in the right position (this is how mine is, too). To avoid opening up a different discussion, the block beneath it is for a spinnaker halyard that Howard knows is in the wrong location (this is the "Before" picture, I'm waiting for the "After"). http://msog.org/qflag/audsley_masthead.jpg I'd like to have some shots of properly rigged mastheads fore and aft of a 15, 17, and 23 for reference on the MSOG. Doug At 08:40 PM 2/3/03 -0800, you wrote: It surprises me that the bolt bent. Is the bolt set up so that the forestay goes thru a machined slot in the face of the mast and hangs on the bolt on the INSIDE of the mast? Jerry ----- Original Message ----- From: "Stanley Winarski" <winarski(a)cox.net> To: <montgomery_boats(a)mailman.xmission.com> Sent: Monday, February 03, 2003 6:04 AM Subject: Questions on M15 rigging - Bent bolt I noticed that bolt was "bent" when I first got my M15 in 1981. I assumed it was intentionally bent when it was installed so that the forestay would stay centered. I had occasion to remove and reinstall it this past summer when I ran wiring in the mast and did not notice any change (it is now 21 years later). Stan Winarski m15, #177, Carol II

1 0

(no subject)
by Bill Riker 06 Feb '03

06 Feb '03

s.mcclellan(a)attbi.com writes: "I need to attach a block to the mast for the spinnaker halyard, above the forestay attachment. Does anyone have an idea how far above the forestay the block should be attached?" When I bought a cruising spinnaker from Kern in 1999, he specified a Harken #166 block (WM #153734) attached with a Ronstan #180 light duty block hangar (WM#120980). The attachment point specified was 8" above the point where the forestay enters the mast. Thost fittings are still shown in the WM 2002 master catalog. It worked for me! Hope this helps. Bill Riker M-15 #184 Storm Petrel

1 0

MON crisis averted
by Doug King 06 Feb '03

06 Feb '03

I think I'm in good shape on the rest of the MON issues. A few folks have been kind enough to offer them. Thanks all, Doug ------------------------------------------ Doug King M-17 #404 "Vixen" Montgomery Sailboats Owners Group Web site: http://msog.org Email: mailto:msog@msog.org

1 0

RE: M_Boats: (no subject)
by Randy Graves 05 Feb '03

05 Feb '03

Steve, Great web site! Thanks for the forward. Randy G. -----Original Message----- From: s.mcclellan(a)attbi.com [mailto:s.mcclellan@attbi.com] Sent: Wed 2/5/2003 9:09 AM To: MBoats Listserver Cc: Subject: M_Boats: (no subject) In my quest to get information about rigging and trimming spinnakers (thanks by the way to those of you how responded to my questions yesterday) I ran into this website for UK Sails which PURPORTS to be an "encyclopedia of sails" but which in fact is (to me) a VERY useful (brief!) little introduction to identifying, naming, rigging and trimming all different kinds of sails. Especially good for those of us who may not know all the proper nautical names for everything--here you can learn them. Anyway for those who might be interested the URL is: http://www.uksailmakers.com/encyclopedia/encyclopedia.html#1 -- Steve McClellan~~M15~#152~~Chicago _______________________________________________ http://mailman.xmission.com/cgi-bin/mailman/listinfo/montgomery_boats

1 0

(no subject)
by s.mcclellan＠attbi.com 05 Feb '03

05 Feb '03

In my quest to get information about rigging and trimming spinnakers (thanks by the way to those of you how responded to my questions yesterday) I ran into this website for UK Sails which PURPORTS to be an "encyclopedia of sails" but which in fact is (to me) a VERY useful (brief!) little introduction to identifying, naming, rigging and trimming all different kinds of sails. Especially good for those of us who may not know all the proper nautical names for everything--here you can learn them. Anyway for those who might be interested the URL is: http://www.uksailmakers.com/encyclopedia/encyclopedia.html#1 -- Steve McClellan~~M15~#152~~Chicago

1 0

Re: M_Boats: Arizona M23's
by Michael L Bowden 05 Feb '03

05 Feb '03

Hi Lenny, That would be great to acquire more pics of the rare M23. I am also curious about Jolkin II. Have you seen her? Please forward any jpegs to my daily E-mail address: bownez(a)sprynet.com. Aren't digital cameras fabulous? I recently bought an Olympus D340L and love it. Thanks! Bones ________________________________________________________________ Sign Up for Juno Platinum Internet Access Today Only $9.95 per month! Visit www.juno.com

1 0