- USR-TC - mailman.xmission.com

Upgrading to V92 with NMC card set
by RComSA - JARH 24 Sep '03

24 Sep '03

Hello, I am beginning to learn about TCs. I read in an auction that you can upgrade any TC with Hiper DSPs using an NMC Pentium III 600 set. How is this possible? I appreciate any explanation about this. Thank you

1 0

xmission: Is this normal?
by alex 23 Sep '03

23 Sep '03

I got an email, that ... "Your membership in the mailing list USR-TC has been disabled due to excessive bounces The last bounce received from you was dated 23-Sep-2003. You will not get any more messages from this list until you re-enable your membership. You will receive 3 more reminders like this before your membership in the list is deleted. To re-enable your membership, you can simply respond to this message (leaving the Subject: line intact), or visit the confirmation page ..." bla bla bla. When I enter that URL provided there, server tells "Bad confirmation string", replying to that message (without RE:) has the same result. Whats up? Am I only one, who got message, like this today? -- alex, ICQ# 219089461, Current status

3 2

Test 2
by SWDT Inc. 23 Sep '03

23 Sep '03

Test 2 Shannan Young sky1(a)airmail.net Southwest Data Technology, Inc. 401 S. Sherman Street Suite #211 Richardson, TX 75081 972-739-7010 972-739-7013 (Fax) www.swdt.com

1 0

TEST
by SWDT Inc. 23 Sep '03

23 Sep '03

Test sky1(a)airmail.net Southwest Data Technology, Inc. 401 S. Sherman Street Suite #211 Richardson, TX 75081 972-739-7010 972-739-7013 (Fax) www.swdt.com

2 1

RE: [USR-TC] Which Setting?????
by Kirti S. Bajwa 23 Sep '03

23 Sep '03

Hello: Please tell me what am I doing wrong? chdev span1 : command does not work chdev span : it does work and span is changed to "span1>" set : command returns error message as invalid commond or command not visible at this level -------------- Can I change these values in TCM? Thanks. Kirt -----Original Message----- From: ISN Support Staff [mailto:support@isn.net] Sent: Monday, September 22, 2003 3:43 PM To: Discussion "relating to the 3Com/US Robotics Total Control modem systems. Subject: Re: [USR-TC] Which Setting????? Hi Kirti, I had a similar problem when setting up my DSP (only I got a fast bus signal instead of a message.) It turned out it was one of the T1 settings on the DSP. Try entering the following commands on the DSP and see if it helps. If not, contact your telco and see if you can get the exact line settings, you might be using a different line configuration than I have (in fact, it's fairly likely that you are.) chdev span1 set dtrnktyp emtype2 set diotrst wink set daackwnk disable set lcoding bz8s set ltype esf chdev tslot set daackwnk disable Then save the config (cmd svspcfg) and reboot the card (reboot) If it doesn't work, do the chdev span1 command and then enter the set commands without the last argument (ie, "set dtrnktyp") to see the available options, and call your telco to see if they can tell you which one to use. As far as I know, for incoming calls, those are the 6 most important settings that will cause line problems. You also may want to double check that your HiperDSP isn't set in loopback mode, but to be honest, I don't know how to do that (cmd loconfig maybe) On Mon, 2003-09-22 at 17:35, Kirti S. Bajwa wrote: > Hello List: > > > > I thought I had set the HiPer ARC & HiPer DSP cards and I was ready to > Boggie!!! > > > > However, when I try to dial-in 423-727-6248, I get a phone company > recording saying that the line is temporary down. Lights on the HiPer > DSP cards are lit as follows: > > > > RN/FL - GREEN > > CAR - GREEN > > ALM - > > LPBK/D-ALM - GREEN > > > > > > When I connect the line to my current box, it receives calls with no > problem. > > > > I know the problem is one or more setting, but which one. Does anybody > had this happened to them so the problem is narrowed down to a > specific setting? I am leaving 423-727-6248 connected to the 3Com box > and any one can call this number and hear the telephone company's > recording. It will not cost any money because the call will not be > completed. > > > > Thanks. > > > > Kirt Bajwa > TIB Computer Systems > Mountain City, TN 37683 > > Tel: (423) 727-3001 > > eMail: kbajwa(a)tib.com > > > > > > ______________________________________________________________________ > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

2 1

Which Setting?????
by Kirti S. Bajwa 22 Sep '03

22 Sep '03

Hello List: I thought I had set the HiPer ARC & HiPer DSP cards and I was ready to Boggie!!! However, when I try to dial-in 423-727-6248, I get a phone company recording saying that the line is temporary down. Lights on the HiPer DSP cards are lit as follows: RN/FL - GREEN CAR - GREEN ALM - LPBK/D-ALM - GREEN When I connect the line to my current box, it receives calls with no problem. I know the problem is one or more setting, but which one. Does anybody had this happened to them so the problem is narrowed down to a specific setting? I am leaving 423-727-6248 connected to the 3Com box and any one can call this number and hear the telephone company's recording. It will not cost any money because the call will not be completed. Thanks. Kirt Bajwa TIB Computer Systems Mountain City, TN 37683 Tel: (423) 727-3001 eMail: kbajwa(a)tib.com <mailto:kbajwa@tib.com>

2 1

NMC Software
by Mike Cisar 22 Sep '03

22 Sep '03

Does anybody have a copy of hm050505.nac floating around in their SDL directory, I'm guessing my copy is corrupt since I seem to be able to flash with any version other than that (the one I need, naturally :-) *pulls out remaining hair* Pls drop me a note off-list. On another note, does anyone know what the highest firmware version is for the Hiper ARC and Hiper NMC that will support/recognize Quad Modems and the Dual T1-PRI NAC ? Cheers & thanks, >>>>> Mike <<<<<

1 0

RE: [USR-TC] HiPer ARC & TCM!!!!
by Kirti S. Bajwa 22 Sep '03

22 Sep '03

Thanks. I will use CLI. Kirt -----Original Message----- From: Wayne Barber [mailto:barberw@tidewater.net] Sent: Monday, September 22, 2003 11:39 AM To: Discussion relating to the 3Com/US Robotics Total Control modem systems. Subject: Re: [USR-TC] HiPer ARC & TCM!!!! TCM was never meant to configure or control the ARC. It's only use with the ARC is to display hardware and software versions. The results you are seeing are normal. HARM, IMHO, was never a reliable product. You are better off using CLI to program the ARC. On 20 Sep 2003 at 17:36, Kirti S. Bajwa wrote: > Hello List: > > I finally figured out how to configure HiPer ARC using CLI & HARM. However, > when I display ARC in TCM, none of the settings are showing! Can someone > explain why? > > Thanks. > > Kirt Bajwa > TIB Computer Systems > Mountain City, TN 37683 > Tel: (423) 727-3001 > eMail: kbajwa(a)tib.com <mailto:kbajwa@tib.com> > > Wayne Barber Coastal Telco Services _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

HiPer ARC & TCM!!!!
by Kirti S. Bajwa 22 Sep '03

22 Sep '03

Hello List: I finally figured out how to configure HiPer ARC using CLI & HARM. However, when I display ARC in TCM, none of the settings are showing! Can someone explain why? Thanks. Kirt Bajwa TIB Computer Systems Mountain City, TN 37683 Tel: (423) 727-3001 eMail: kbajwa(a)tib.com <mailto:kbajwa@tib.com>

3 2

RE: [USR-TC] HiPer ARC & TCM!!!!
by Kirti S. Bajwa 22 Sep '03

22 Sep '03

Yes. Kirt -----Original Message----- From: Lewis Bergman [mailto:lbergman@wtxs.net] Sent: Monday, September 22, 2003 9:33 AM To: Discussion relating to the 3Com/US Robotics Total Control modem systems. Subject: Re: [USR-TC] HiPer ARC & TCM!!!! -----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 On Saturday 20 September 2003 04:36 pm, Kirti S. Bajwa wrote: > Hello List: > > I finally figured out how to configure HiPer ARC using CLI & HARM. However, > when I display ARC in TCM, none of the settings are showing! Can someone > explain why? Are you doing a "save all to NVRAM"? - -- Lewis Bergman Texas Communications 4309 Maple St. Abilene, TX 79602-8044 915-695-6962 ext 115 -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.0.7 (GNU/Linux) iD8DBQE/bvolpT00mQjG01gRAt1lAJwKDwOSU/zUye8UTIOl0gHS+i3yWgCeOJmH dflpXLJxtS4lAz1ZlHdtR+U= =2Wx6 -----END PGP SIGNATURE----- _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0