- USR-TC - mailman.xmission.com

Multilink PPP Problem
by John R. Aynesworth 27 May '04

27 May '04

I don't have MPIP configured at all--as best I can figure, that would only be necessary if I had more than one Total Control. Am I wrong? John R. Aynesworth Alexssa/Hnet 303 N. Main St. West Bend, WI 53095 voice: (262) 338-3742 fax: (262) 338-3387 email: jra(a)hnet.net

1 0

Total Control Software and Support?
by Rob 27 May '04

27 May '04

I just bought some brand new 3Com TC 1000 gear that had been tied up in a tax dispute involving 3com and the original distributor, and the equipment is fully new and registerable. But I have had no luck in finding out who the heck to register it with anymore now that commworks is gone. Who knows? Thanks! Rob

3 5

WTB: 3Com TC1000 gear
by Stephen Rivera - WRCA.Net 24 May '04

24 May '04

Hello Folks, 8- USR/3COM TC1000 Power Sets 130A DC PSU & PSI (Front and Back card) 2- 3COM PN# 3C0504218-00 333NMC 2- 3COM Upstream Receiver PN# 69-002970-00 Ant- Quad A/D Fan Out cables Please reply with available de-installed hardware Thanks. Steve Rivera WR Consultant Associates, Inc. Dir: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

1 0

E1/R2 timeout
by Anil 22 May '04

22 May '04

Hi, recently in bought a new E1/R2 line from telco connected to my 3Com tc 1000. it works fine with most of the customes. but for some remote telco exchanges, when the user dials my new e1/r2 number they get 3 beeps and then the error "line is busy". when i contacted telco they said that i have to reduce the timeout delay on my 3com box. can anyone suggest how can i achive to do this.. please help me out. also let me know wheather i need not set the timeout on perticular card or the entire chaises. Thanks & Regards Anil

2 1

Multilink PPP problem
by John R. Aynesworth 21 May '04

21 May '04

Can anyone shed any light on the following error message from MONITOR PPP? New PPP Call received on interface slot:2/mod:8 PPP - Authentication Complete to jbusisdn. PPP - Expanded Authentication Complete to jbusisdn. (IPCP) Layer Down for Bundle 23075, Link 42174784, to jbusisdn. PPP connection down to jbusisdn. Radius is assigning a single IP to the user. The user is using a Cisco ISDN 802 router configured for multilink PPP. The first call succeeds and is assigned the IP--the second call fails with the above error. If I modify Radius to give a dynamic IP address, two calls are established with two IP addresses--even though multilink PPP is configured in the router. I've got other users using other brand routers getting two channels bonded with no problem. Anybody have any thoughts? John R. Aynesworth Alexssa/Hnet 303 N. Main St. West Bend, WI 53095 voice: (262) 338-3742 fax: (262) 338-3387 email: jra(a)hnet.net

2 1

(no subject)
by Homer Pialda 20 May '04

20 May '04

usr gurus, i am using total control netsever 16 version 3.1.4, does this support session time-out attributes? i need it on our prepaid software to automatically disconnect our client when their time lapses during connection. pls __________________________________ Do you Yahoo!? Win a $20,000 Career Makeover at Yahoo! HotJobs http://hotjobs.sweepstakes.yahoo.com/careermakeover

3 4

NFAS Call handling problem
by Adam Barnhill 19 May '04

19 May '04

Hi guys, I'm setting up a new location using an NFAS PRI configuration. The hardware consists of Multispans with an ARC II and NMC333. The code being run is TCS 4.5, specifically 3.5.109 Mdsp, 5.3.110 arc2, 8.7.3 nmc NFAS is setup as follows: Group 0 DeviceIDs 0-6 for a total of 7 spans. DeviceID 0 and 1 are my primary and secondary D Channels. Trunk Settings are B8ZS/ESF with a switch type of NI2. The D channels look good and everything appears normal, but the problem I am having is that calls made to the TC get dead air. >From TCS I see the DNIS information and that a call is coming in, but the call never completes. A Q.931 trace is below for those that might find that helpful. Please note that by changing the config to fas PRI on both sides, the modems will take calls. It's only when in NFAS mode. The softswitch in case anybody cares is made by Metaswitch. I appreciate any and all responses, thank you. Does anybody have a working NFAS setup in the US? L1 : Physical : Span 0 : Network -> User L2 : Data Link : SAPI 0 : TEI 0 : C/R 1 : Frame I : Ns 11 : Nr 20 : P/F 0 L3 : Call Ref : 1280 Message : SETUP IE Name : Bearer capability Octet 3 : Capability - CCITT coding, Speech Octet 4 : Mode/rate - Circuit mode, 64 kbps Octet 5 : Layer 1 - G.711 u-law IE Name : Channel identification Octet 3 : Interface - Explicitly identified, primary rate : Selection - Preferred, B-channel, as follows Octet 3.1 : Identifier - 6 Octet 3.2 : Channels - CCITT coding, channel number, B-channel units Octet 3.3 : Number(s) - 24 IE Name : Progress indicator Octet 3 : Location - CCITT coding, remote public network (RLN) Octet 4 : Progress - Origination address is non ISDN IE Name : Calling party number Octet 3 : Type - National number : Plan - ISDN/telephony numbering plan (E.164) Octet 3a : Screening - Presentation restricted, network provided IE Name : Calling party number Octet 3 : Type - Unknown : Plan - Unknown Octet 3a : Screening - Number not available due to interworking, network provided IE Name : Called party number Octet 3 : Type - Subscriber number : Plan - ISDN/telephony numbering plan (E.164) Octet 4+ : Number - 7122900 Time 13:31:43.105 TX0: 02 01 01 18 : Total 4 L1 : Physical : Span 0 : User -> Network L2 : Data Link : SAPI 0 : TEI 0 : C/R 1 : Frame RR : Nr 12 : P/F 0 Time 13:31:43.107 TX0: 00 01 28 18 08 02 85 00 02 18 04 E9 86 83 98 : Total 15 L1 : Physical : Span 0 : User -> Network L2 : Data Link : SAPI 0 : TEI 0 : C/R 0 : Frame I : Ns 20 : Nr 12 : P/F 0 L3 : Call Ref : 1280 Message : CALL PROCEEDING IE Name : Channel identification Octet 3 : Interface - Explicitly identified, primary rate : Selection - Exclusive, B-channel, as follows Octet 3.1 : Identifier - 6 Octet 3.2 : Channels - CCITT coding, channel number, B-channel units Octet 3.3 : Number(s) - 24 Time 13:31:43.108 TX0: 00 01 2A 18 08 02 85 00 07 : Total 9 L1 : Physical : Span 0 : User -> Network L2 : Data Link : SAPI 0 : TEI 0 : C/R 0 : Frame I : Ns 21 : Nr 12 : P/F 0 L3 : Call Ref : 1280 Message : CONNECT Time 13:31:43.109 TX0: 00 01 2C 18 08 02 85 00 45 08 02 80 90 : Total 13 L1 : Physical : Span 0 : User -> Network L2 : Data Link : SAPI 0 : TEI 0 : C/R 0 : Frame I : Ns 22 : Nr 12 : P/F 0 L3 : Call Ref : 1280 Message : DISCONNECT IE Name : Cause code Octet 3 : Location - CCITT coding, user (U) Octet 4 : Cause 16 - Normal call clearing Time 13:31:43.110 RX0: 00 01 01 2A : Total 4 L1 : Physical : Span 0 : Network -> User L2 : Data Link : SAPI 0 : TEI 0 : C/R 0 : Frame RR : Nr 21 : P/F 0 Time 13:31:43.111 RX0: 00 01 01 2C : Total 4 L1 : Physical : Span 0 : Network -> User L2 : Data Link : SAPI 0 : TEI 0 : C/R 0 : Frame RR : Nr 22 : P/F 0 Time 13:31:43.112 RX0: 00 01 01 2E : Total 4 L1 : Physical : Span 0 : Network -> User L2 : Data Link : SAPI 0 : TEI 0 : C/R 0 : Frame RR : Nr 23 : P/F 0 Time 13:31:43.118 RX0: 02 01 18 2E 08 02 05 00 4D : Total 9 L1 : Physical : Span 0 : Network -> User L2 : Data Link : SAPI 0 : TEI 0 : C/R 1 : Frame I : Ns 12 : Nr 23 : P/F 0 L3 : Call Ref : 1280 Message : RELEASE Time 13:31:43.118 TX0: 02 01 01 1A : Total 4 L1 : Physical : Span 0 : User -> Network L2 : Data Link : SAPI 0 : TEI 0 : C/R 1 : Frame RR : Nr 13 : P/F 0 Time 13:31:43.118 TX0: 00 01 2E 1A 08 02 85 00 5A : Total 9 L1 : Physical : Span 0 : User -> Network L2 : Data Link : SAPI 0 : TEI 0 : C/R 0 : Frame I : Ns 23 : Nr 13 : P/F 0 L3 : Call Ref : 1280 Message : RELEASE COMPLETE -- Adam Barnhill Support Engineer, TotallyFabricated.com Information Technology Engineer, Poplar Bluff Internet, Inc. / Semo.net P.O. Box 190 | Poplar Bluff, MO 63902 | 573.686.9114, <http://www.semo.net/> Home of TotallyFabricated.com the creators of Total Scrutinizer

2 1

WTS: Hiper DSP E1- 30 channel
by Stephen Rivera - WRCA.Net 14 May '04

14 May '04

All new boxed with paperwork etc Qty Available USR 992267-00 Total Control HiPer DSP 30 Channel (E1 Card Set) 30 day warranty Individual cards and E1 bundle pricing available. Steve Rivera WR Consultant Associates, Inc. Dir: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

2 1

Hiper DSP E1, Telco C7/SS7 signaling
by Russell Newberry 11 May '04

11 May '04

Hello all, Will Hiper DSP E1 cards work with Telco C7, SS7 signaling? My customer has checked on E1 Hiper DSP card setting, but there is no option for SS7/C7 signaling. There are three signaling types: R2 digital, P7, and R2EM. Any suggestions? Thanks, Russell Newberry ==================== Maxis Technologies, Inc 433 W. Wilshire Blvd. Ste 2B Oklahoma City, OK 73116 Voice: 1-800-79-MAXIS Int'l: 1-405-842-3331 FAX: 1-405-841-7882 find us on the web at www.maxistech.net email to: russell(a)maxistech.net AOL IM "RUSSELLatMAXIS"

2 1

RE: [USR-TC] WTB: Quad Modem 4 port Fan out cables
by Edward Rempala 10 May '04

10 May '04

Do you still need them, If so how many do you need? Edward Rempala WorldNet Access / Page 21 >>If you have these cables available. >>They are Quad modem accessories. >> Mini SCSI interface to connect to quad modem nic , other end is 4 port RS232. >> Will buy Qty or individual.

1 0