- USR-TC - mailman.xmission.com

RE: [USR-TC] HiperDSPs not talking to Telco
by Babar Kazmi 27 Jan '03

27 Jan '03

3 4

RE: [USR-TC] TCS 4.7 code HELP!!!
by Joel - Fox Computers 27 Jan '03

27 Jan '03

I'm not familiar with any "SNMP tools" - anyone lend me some help in what's available to use and where to get? -----Original Message----- From: Scott M. Trautman [mailto:usrtc20021002@scott.trautman.net] Sent: Monday, January 27, 2003 10:29 AM To: usr-tc(a)mailman.xmission.com Subject: Re: [USR-TC] TCS 4.7 code HELP!!! Well, remember that you can end up doing 100% via command line, SNMP instead of their cute graphical wrappers. Not much of a choice at this point: pony up for CEM or get used to the command line & SNMP tools if you want to have the latest code. I do sure wish TCM still worked - mainly because THAT I could easily show and teach my fellow techs fairly rapidly for the basic functions. At this point in the game I'm not inclined to bop out what, a grand (? per year?), for this pretty crude software. I couldn't get the CEM beta to install. Instructions totally suck. I'm not sure what they're thinking. Not that I dedicated the day to it. With as crappy as the instructions and install is, doesn't make me believe the program is going to really be worth a pinch of snot. SMT _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

Changing configuration setting in Hiper Access Router Card
by Jim Mc Cay 27 Jan '03

27 Jan '03

Hello, I'm trying to setup a Hiper Access Router Card using Hyperterminal. I've got (I believe) pretty much everything setup but I'm needing to change one thing. If you were to run a sho ppp setings at the command prompt, towards the end of the info that is listed I'm needing to change this setting: PPP Process RADIUS Challenge during PAP: I'm needing to change it from DISABLED to ENABLED. I've done this once before but I've forgotten the command(s) that I need to type in. Could someone point me to where I could find documentation or just tell me what I need to type?? Thanks-You, jim

1 0

Problem with USR Sportster 56K and v.92
by Walt Gnann 27 Jan '03

27 Jan '03

I recently upgraded our TC chassis to NMC 8.6.3, HARC 5.3.110, HDSPs 3.5.109. I enabled v.44 data compression and all the v.92 settings on the HDSPs. I had a few problems with folks staying connected while the v.92 PCM Upstream setting was enabled. Basically they would connect fine then get dropped after a few minutes with a failure to retrain error. So, I disabled PCM and everything seemed fine. Newest problem is with a Sportster 56K modem. It will start to handshake then a second or two into the handshake it will give a long, high pitched tone and fail to connect. If I disable the v.92 master setting on the HDSP it will connect just fine. Has anyone else encountered this? Any suggestions? Walt ----------------------------------------------- Walter N. Gnann ISLC, President wgnann(a)islc.net http://www.islc.net 843.770.1000 fax: 843.770.1002 -----------------------------------------------

1 0

Re: [USR-TC] NetServer Radius
by alex 27 Jan '03

27 Jan '03

do you have radius secrets correct? actually what problems do you have? (try set chapfst on/off set pap off/on if you radius can/cant do chap and set radius_option ...) > I am running radius on NT4.0. I am adding an additional netserver and am > have an authenication problem. I believe that it is because of a older > version of netserver. If anyone can provide a copy of version 3.8.1, I > think this will solve my problem. Thanks for your help. > Best Regards, > Glenn >

1 0

TCS 4.7 code HELP!!!
by Adam Barnhill 27 Jan '03

27 Jan '03

Remember that TCS 4.7 is only compatible with Common Element Manager. I'm pretty sure you'll need a package install key as well. Am I the only one that thinks CEM is much more difficult to use than TCM? I feel like I'm going to have to read the manual 3 times just to be able to do simple things I could do in TCM by exploration. -- Adam Barnhill Support Engineer, TotallyFabricated.com Information Technology Engineer, Poplar Bluff Internet, Inc. / Semo.net P.O. Box 190 | Poplar Bluff, MO 63902 | 573.686.9114, <http://www.semo.net/> Home of TotallyFabricated.com the creators of Total Scrutinizer

1 0

HiperDSPs not talking to Telco
by Kevin Hemsley 27 Jan '03

27 Jan '03

We just upgraded one of our small POPs from Quad modems and NetServers to HiperDSPs and HiperArcs. I have configured the HiperDSPs like the T1 cards were but we aren't taking calls. The telco sends us a siezure and gets no answer back. The switch is a DMS10. The CO tech said he is seeing the following: Trunk 17 Message: Sender timeout occured durring selection of an outgoing trunk. They don't see answer supervision back, so they drop the call. I have tried changing Signal Modes, adjusting the E&MII timers with the telco, but nothing seems to work. I would appreciate any feedback ff anyone has any ideas. My DSP cards are configured like this: Framing Mode dsx1D4 Line Coding Options dsx1AMI Circuit Identifier Loopback Configuration dsx1NoLoop Signal Mode robbedBit Transmit Clock Source loopTiming NIC Type longHaul Response to Remote Loopback respond Jitter Attenuation attenJitterOnTxmtr Transmit Line Build Out dB0pt0 Dial In Address noAddress Dial In/Out Trunk Start Signal Type wink Ack Wink On Dial In Address Info Received enabled Dial Out Address Delay 70 Dial In/Out Trunk Type eAndMTypeII Primary Switch Type priSwDMS100 Idle Byte Pattern 254 Receiver Gain dB26 Tone Type mf Number of DTMF Tones 4 Send Code dsx1SendNoCode External Signaling Mode (will take effect next boot) none Overlap Receiving Mode disable Overlap Receiving Inbound Digits Expected 12 Overlap Receiving Timeout Delay 12 Answer Supervision Delay Time. 11 E-lead Disconnect Debounce Time 30 Telco Disconnect Sanity Time 10 Wink Duration 20 V42->WAN Disconnect Delay Time 0 Telco init Disconnect Delay Time 0 Seizure to Wink Delay Time 22 Thanks, Kevin Hemsley kev(a)ida.net

2 1

RE: [USR-TC] TCS 4.7 code HELP!!!
by Joel - Fox Computers 27 Jan '03

27 Jan '03

Good point! I was assuming that it was a limited use thing so I could give it a try before I buy it. Suppose I should check into that before I upgrade, huh? Thanks for the reminder. - Joel -----Original Message----- From: Adam Barnhill [mailto:adam@semo.net] Sent: Monday, January 27, 2003 9:49 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] TCS 4.7 code HELP!!! Remember that TCS 4.7 is only compatible with Common Element Manager. I'm pretty sure you'll need a package install key as well. Am I the only one that thinks CEM is much more difficult to use than TCM? I feel like I'm going to have to read the manual 3 times just to be able to do simple things I could do in TCM by exploration. -- Adam Barnhill Support Engineer, TotallyFabricated.com Information Technology Engineer, Poplar Bluff Internet, Inc. / Semo.net P.O. Box 190 | Poplar Bluff, MO 63902 | 573.686.9114, <http://www.semo.net/> Home of TotallyFabricated.com the creators of Total Scrutinizer _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

2 1

RE: [USR-TC] TCS 4.7 code HELP!!!
by Joel - Fox Computers 27 Jan '03

27 Jan '03

You're right - CEM does look difficult - the installation instructions are killing me. Maybe I will hold off on installing that. -----Original Message----- From: Joel - Fox Computers Sent: Monday, January 27, 2003 10:06 AM To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] TCS 4.7 code HELP!!! Good point! I was assuming that it was a limited use thing so I could give it a try before I buy it. Suppose I should check into that before I upgrade, huh? Thanks for the reminder. - Joel -----Original Message----- From: Adam Barnhill [mailto:adam@semo.net] Sent: Monday, January 27, 2003 9:49 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] TCS 4.7 code HELP!!! Remember that TCS 4.7 is only compatible with Common Element Manager. I'm pretty sure you'll need a package install key as well. Am I the only one that thinks CEM is much more difficult to use than TCM? I feel like I'm going to have to read the manual 3 times just to be able to do simple things I could do in TCM by exploration. -- Adam Barnhill Support Engineer, TotallyFabricated.com Information Technology Engineer, Poplar Bluff Internet, Inc. / Semo.net P.O. Box 190 | Poplar Bluff, MO 63902 | 573.686.9114, <http://www.semo.net/> Home of TotallyFabricated.com the creators of Total Scrutinizer _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

TCS 4.7 code HELP!!!
by Joel - Fox Computers 26 Jan '03

26 Jan '03

OK, So I have a Source-T support contract. Most people here know that. It seems that Source-T does not have ANY of the TCS 4.7 stuff on their website to download, and I was gonna try upgrading to it today. Anyone have the following files and can forward them to me? cem525.zip ne050702.zip hm100105.zip hd030704.zip If you can, much appreciated. Thanks, Joel

2 1