- USR-TC - mailman.xmission.com

RE: [USR-TC] HiperDSPs not talking to Telco
by Joel - Fox Computers 24 Jan '03

24 Jan '03

change the "Number of DTMF tones" to 0 and see if it answers then -----Original Message----- From: Kevin Hemsley [mailto:kev@ida.net] Sent: Friday, January 24, 2003 11:42 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] HiperDSPs not talking to Telco We just upgraded one of our small POPs from Quad modems and NetServers to HiperDSPs and HiperArcs. I have configured the HiperDSPs like the T1 cards were but we aren't taking calls. The telco sends us a siezure and gets no answer back. The switch is a DMS10. The CO tech said he is seeing the following: Trunk 17 Message: Sender timeout occured durring selection of an outgoing trunk. They don't see answer supervision back, so they drop the call. I have tried changing Signal Modes, adjusting the E&MII timers with the telco, but nothing seems to work. I would appreciate any feedback ff anyone has any ideas. My DSP cards are configured like this: Framing Mode dsx1D4 Line Coding Options dsx1AMI Circuit Identifier Loopback Configuration dsx1NoLoop Signal Mode robbedBit Transmit Clock Source loopTiming NIC Type longHaul Response to Remote Loopback respond Jitter Attenuation attenJitterOnTxmtr Transmit Line Build Out dB0pt0 Dial In Address noAddress Dial In/Out Trunk Start Signal Type wink Ack Wink On Dial In Address Info Received enabled Dial Out Address Delay 70 Dial In/Out Trunk Type eAndMTypeII Primary Switch Type priSwDMS100 Idle Byte Pattern 254 Receiver Gain dB26 Tone Type mf Number of DTMF Tones 4 Send Code dsx1SendNoCode External Signaling Mode (will take effect next boot) none Overlap Receiving Mode disable Overlap Receiving Inbound Digits Expected 12 Overlap Receiving Timeout Delay 12 Answer Supervision Delay Time. 11 E-lead Disconnect Debounce Time 30 Telco Disconnect Sanity Time 10 Wink Duration 20 V42->WAN Disconnect Delay Time 0 Telco init Disconnect Delay Time 0 Seizure to Wink Delay Time 22 Thanks, Kevin Hemsley kev(a)ida.net

2 1

RE: [USR-TC] No longer on list?
by Joel - Fox Computers 24 Jan '03

24 Jan '03

I get that everytime. -----Original Message----- From: Todd Bertolozzi [mailto:berto@voyager.net] Sent: Friday, January 24, 2003 10:32 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] No longer on list? Does everyone else always get a user-unknown error when posting to this list? The original message was received at Fri, 24 Jan 2003 10:26:30 -0600 from mailman.xmission.com [198.60.22.29] ----- The following addresses had permanent fatal errors ----- <customercare(a)uspower.net> (expanded from: <customercare(a)uspower.net>) ----- Transcript of session follows ----- mail.local: unknown name: customercare 550 <customercare(a)uspower.net>... User unknown Can we take this person off the list? Todd _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

2 1

Hiper Eauipment
by sky1 24 Jan '03

24 Jan '03

Ok guys I am now totally loaded down with Hiper Gear and Quad Digital V.34 (V.90) bundles. Need to move this stuff. If anyone has any requirements at all let me know. Make me an offer on what you are looking for and Ill take it under consideration. This stuff is in excellent condition. Thanks for your time, Shannan Young SouthWest Data Technology, Inc. 972-739-7010 972-739-7013 (Fax) sky1(a)airmail.net www.swdt.com

1 0

TC routing
by Peter Galbraith 24 Jan '03

24 Jan '03

Is is possible to have my HiperNMC route more than one way. I am trying to set up a failover system that will use 'costs' to route the packets depending on availibility. I can obviously do this with another machine if needed, but I thought I would ask and see if anyone has any ideas. Thanks, --Peter Galbraith

1 0

RE: [USR-TC] HiperDSPs not talking to Telco
by Joel - Fox Computers 24 Jan '03

24 Jan '03

Are you sure on the Framing and Line Coding (the D4 and the AMI)? Whereas many settings will make minor differences, Framing and Line Coding are critical. Because D4 and AMI are kinda the "old" standards, if those are correct, I assumed the mf tones are probably correct as well. It couldn't hurt to try changing to dtmf, but if you've got the number of tones set to zero then the tone type should become irrelevent. For the record, my telco is running an Ericcson AXE10, not too old, new enough that I've got ESF/BMI, and they can only send mf tones (or at least that's what they told me) -----Original Message----- From: Kevin Hemsley [mailto:kev@ida.net] Sent: Friday, January 24, 2003 12:26 PM To: usr-tc(a)mailman.xmission.com Subject: Re: [USR-TC] HiperDSPs not talking to Telco >yes - if the Hiper ARC does not have ownership of the DSP's, they won't answer. > >Also, if you have your DTMF tones set to 4, and the telco doesn't send them, the DSP will sit there and wait and not reply until it >receives them, so the call dies. Yes the ARC does have onership. There are only 4 DSPs installed and only 3 active: tc-sm1> list chassis Slot Owner Description Ports Type Console 1 YES 24 Channel High Density Modem 24 DYNAMIC YES 2 YES 24 Channel High Density Modem 24 DYNAMIC YES 3 YES 24 Channel High Density Modem 24 DYNAMIC YES 4 YES 24 Channel High Density Modem 23 DYNAMIC YES 5 YES 24 Channel High Density Modem 24 STATIC NO 6 YES 24 Channel High Density Modem 24 STATIC NO 7 YES 24 Channel High Density Modem 24 STATIC NO 8 YES 24 Channel High Density Modem 24 STATIC NO 9 YES 24 Channel High Density Modem 24 STATIC NO 10 YES 24 Channel High Density Modem 24 STATIC NO 11 YES 24 Channel High Density Modem 24 STATIC NO 12 YES 24 Channel High Density Modem 24 STATIC NO 13 YES 24 Channel High Density Modem 24 STATIC NO 14 YES 24 Channel High Density Modem 24 STATIC NO 15 YES 24 Channel High Density Modem 24 STATIC NO 16 YES HiPer Access Router NAC 0 DYNAMIC NO Thanks, Kevin Hemsley kev(a)ida.net _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

2 1

RE: [USR-TC] Error Messages
by Joel - Fox Computers 24 Jan '03

24 Jan '03

In TCM, when you click the trunk LED's at the top of the card and do Performance->Session Monitor->Timeslots(ALL), in the "Functional Group Setup Window" you can then select "DS0 Timeslot Status" and "DS0 Service State". The table you provided relates to "DS0 Timeslot Status", I'm seeing the "9" in the "DS0 Service State" Column. Thanks! Joel -----Original Message----- From: Todd Bertolozzi [mailto:berto@voyager.net] Sent: Friday, January 24, 2003 10:18 AM To: usr-tc(a)mailman.xmission.com Subject: Re: [USR-TC] Error Messages Browsing the mib file ds0 I see that under ds0StatDs0 the following: ds0StatDs0 OBJECT-TYPE SYNTAX INTEGER{ other(1), idle(2), dialingIn(3), dialingOut(4), connectedIn(5), connectedOut(6), softBusyOut(7), hardBusyOut(8), autoBusyOut(9), mdmBusyOut(10), ignoringCalls(11), mdmCallIgnore(12), test(13), alarm(14), transparent(15), unavailable(16), transparentTest(17), unused(18), busyOut(19), fracUnused(20), passThru(21) Todd ----- Original Message ----- From: "Todd Bertolozzi" <berto(a)voyager.net> To: <usr-tc(a)mailman.xmission.com> Sent: Friday, January 24, 2003 11:08 AM Subject: Re: [USR-TC] Error Messages > If you right click on the ds0 timeslot status it should tell you what the > codes or numbers are. On my version of TCM I don't see a 9 though. Just a > 1,2,3,4,5,6,22,23,24,25, and 26. > > Todd > ----- Original Message ----- > From: "Joel - Fox Computers" <jfox(a)foxcomputers.com> > To: <usr-tc(a)mailman.xmission.com> > Sent: Friday, January 24, 2003 10:37 AM > Subject: RE: [USR-TC] Error Messages > > > > Don't know if it's related or not, but the "9" caught my eye. I'm working > with a DSP that won't take any calls and in the session monitor in TCM it > shows "DS0 Service Status" as a "9" where it normally says "InService(2)". > > > > Any solution to this or a suggestion? I saw there was a reply to Todd's > message but I accidentally deleted. Someone please forward to me if you > think it was relevant. > > > > Thanks! > > > > Joel > > > > > > -----Original Message----- > > From: Todd DeWitt [mailto:tdewitt@megalink.net] > > Sent: Friday, January 24, 2003 6:57 AM > > To: usr-tc(a)mailman.xmission.com > > Subject: [USR-TC] Error Messages > > > > > > We've recently begun receiving the following in our syslogs on one of our > > TC's. Anyone know what this means or where to find reference for all the > > messages? > > > > Facility GWC Modem Driver, Level CRITICAL:: callline->callstate = 9 > > > > Todd > > > > > > _______________________________________________ > > USR-TC mailing list > > USR-TC(a)mailman.xmission.com > > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > > _______________________________________________ > > USR-TC mailing list > > USR-TC(a)mailman.xmission.com > > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > > > > > > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

RE: [USR-TC] Error Messages
by Joel - Fox Computers 24 Jan '03

24 Jan '03

Don't know if it's related or not, but the "9" caught my eye. I'm working with a DSP that won't take any calls and in the session monitor in TCM it shows "DS0 Service Status" as a "9" where it normally says "InService(2)". Any solution to this or a suggestion? I saw there was a reply to Todd's message but I accidentally deleted. Someone please forward to me if you think it was relevant. Thanks! Joel -----Original Message----- From: Todd DeWitt [mailto:tdewitt@megalink.net] Sent: Friday, January 24, 2003 6:57 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] Error Messages We've recently begun receiving the following in our syslogs on one of our TC's. Anyone know what this means or where to find reference for all the messages? Facility GWC Modem Driver, Level CRITICAL:: callline->callstate = 9 Todd _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

3 4

RE: [USR-TC] Experiences with newest code?
by Joel - Fox Computers 23 Jan '03

23 Jan '03

I'm having good luck with: DSP: 3.5.105 ARC: 5.3.107 NMC: 8.6.3 Had not heard of 3.5.109 or 5.3.110, but sure would like to get my hands on them if they're out there. Anyone have these? - Joel -----Original Message----- From: I. Dwayne Koonce [mailto:dwayne@txcyber.com] Sent: Wednesday, January 08, 2003 1:20 PM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] Experiences with newest code? Okay, I've recently upgraded all my cards that were lagging on software versions, but now my boss is upset because I upgraded to the newest releases that I've heard people refer to as stable, rather than the absolute bleeding edge. So I told him I'd ask around, and see if I could get other people's opinion of the latest firmware. Right now we've got: HiperDSP: 3.5.105 HiperARC: 5.3.3 HiperNMC: 8.6.3 NMC(486): 7.1.8 We don't have any problems as far as I know--except possibly one with NFAS, but I think that's really a telco issue--but my boss would like to upgrade. So I'm looking for opinions about the TCS 4.5 service releases and/or TCS 4.7. Can anyone tell me if the following versions have worked well/failed spectacularly for them? HiperDSP: 3.5.109, 3.7.4 HiperARC: 5.3.110, 5.7.2 HiperNMC: 10.1.5 _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

4 3

RE: [USR-TC] clearing stuck channels in a hiper dsp???
by Joel - Fox Computers 23 Jan '03

23 Jan '03

Never had one do that, but I would soft-busy the card out, wait for everyone to get off it, then I'd give it a hardware reset. -----Original Message----- From: matthew [mailto:matthew@the-spa.com] Sent: Thursday, January 23, 2003 3:25 PM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] clearing stuck channels in a hiper dsp??? what is the best way to try and troubleshoot like 3 channels in a hiper dsp that seem to be stuck? matthew _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

2 1

leased lines by NETServer 16
by alex 23 Jan '03

23 Jan '03

one of our netservers stops listening for leased line (&l1 is set). it happens after disconnecting of user. port is off (not red/yellow/green). i checked init strings and NVRAM settings - everything is same as on other netservers. reseting port dont help. i wrote &l1 option into nvram and rewrite init string by atz and same problem. any suggestions? (NETServer 16 - OS V3.8.1 modems - V1.0.8)

4 3