December 1999 - USR-TC - mailman.xmission.com

(usr-tc) USR-DOCSIS list
by System Administrator 14 Dec '99

14 Dec '99

Hey guys, Wondering if anyone knew of any lists to subscribe to for 3Com's TC Two-way data over cable equipment?? __________________________________ Justin Ellison System Administrator InternetUSA sysadmin(a)nebi.com http://nebi.com 800-603-3502 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Looking to buy a Total Control
by Mike Storjohann 14 Dec '99

14 Dec '99

I am looking for a Total Control that contains the following: Â 1Â Â Â HiperARC NAC 1Â Â Â Dual V.35 + Ethernet NIC 1Â Â Â NMC NIC and NAC set 2Â Â Â HiperDSP NIC and NAC sets Â 70 Amp Power supply also. Â Please let me know off list if you have this bundle available. Â Thank you. Mike Storjohann Internet Services Administrator HunTel.net mstorjohann(a)huntel.net - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) FS: USR
by Steve Rivera 14 Dec '99

14 Dec '99

Since the list has been slow.... here's some breaking news :) Available this week. 5- Hiper ARC 9- Hiper DSP 5- Hiper NMC (New) Available now 8- Dual T1/E1 nic/nac sets 4- Dual PRI nic/nac sets 36- Quad Digital Modems w/ nic $150 each 10- Netserver PRI (New) 10- NMC (New) Qty- 130A - DC Power Netserver 16 Plus Netserver 16 Netserver 8 MP16 MP8 Chassis Parts Power Supplies Also have the quad cables available. .................................................... Steve Rivera - ISP-NetworkHardware.com (WRCA) sales(a)wrca.net v-732-833-2111 pgr-732-325-1092 ---WAN ACCESS SPECIALIST--- http://www.ISP-NetworkHardware.com Cisco, Ascend, Livingston, USR, Microcom, Computone, Kentrox, Adtran...and more - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Remember my post about 2nd login with same account drops immediat ely?
by Scott Trautman 14 Dec '99

14 Dec '99

Yep, MultiPPP thing. FYI for all of you bound to bang your head against it sooner or later. This fellow's first login with Pstandish was actually an NT server running a proxy (he lead me to believe it was a Win95 machine), and even though not apparently setup for MPPP, it was definately waiting for an MPPP connection, forever, so that the next machine to dial in with same name, Pstandish, got dropped because no way could it bind to that first connection. I don't/didn't know enough about MPPP to know that; is that just an NT thing, or would he have had to set that somewhere regardless of him ever bringing up a 2nd line on the NT machine. Usually MPPP just works for us and I don't find these relatively weird kinds of problems. SMT Scott Trautman 608-240-4638,4637fax Global Dialog Internet www.gdinet.com 2810 Crossroads, STE LL2 Madison WI 53718 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Hello
by Scot Desort 14 Dec '99

14 Dec '99

Hello everyone -- is the list dead? Haven't seen any posts in a while. Did Y2K hit early <g> -- Scot Desort Network Operations Manager NJ Internet Access 973-244-1110 Tech Support 973-303-HELP support(a)njaccess.com - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

Re: (usr-tc) SMS
by Startup Suppliers Ltd. 13 Dec '99

13 Dec '99

Hello list members, Can somebody please advise me what I need to provide Short Message Service linking our ISP to mobile phones. What do I need in terms of hardware and software? Okeyo. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) HiperARC PNS & LNS
by Clayton Zekelman 10 Dec '99

10 Dec '99

I've been playing with some configurations, trying to get the HiperARC to act as a terminator endpoint for L2TP or PPTP sessions, with little success. In my first attempt, I configured DUN with PPTP on a Win95 machine to connect to one of my HiperARCs. It tried to connect - the hiper tired to go out to the radius server for authentication, but rather than sending the username and password, it sent a username of "local", with an unknown password. I'd like to be able to use the Hiper for terminating L2TP sessions from our LEC for DSL customers as well. Any suggestions/comments/experiences? --- Clayton Zekelman Managed Network Systems Inc. (MNSi) 875 Ouellette Avenue Windsor, Ontario N9A 4J6 tel. 519-985-8410 fax. 519-258-3009 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

5 5

Re: (usr-tc) TCM 6.023
by Steve Valiunas 10 Dec '99

10 Dec '99

If you are making span-level changes, make sure you "save T1/E1" on the HiperDSP, then from the NMC, "save chassis to NVRAM" to be safe. The last step is required if you have auto-config enabled on the NMC. Also, you should be using 6.2.17 NMC code (requires TCM 6.0 as well) with the 2.0 HiperDSPs. Note that there is a s/w reset and a h/w reset available on the HiperDSP through TCM. Depending on how you save and how autoConfig is set, each may give you different results. STeve "Sam Lowe" <slowe(a)universalcom.net> on 12/08/99 08:06:35 AM Please respond to usr-tc(a)lists.xmission.com Sent by: "Sam Lowe" <slowe(a)universalcom.net> To: usr-tc(a)lists.xmission.com cc: (Steve Valiunas/MW/US/3Com) Subject: (usr-tc) TCM 6.023 We seem to be having a problem saving settings on our HiPer DSP cards using TCM (we think). When we set the switch type and reset the card it would revert back to the default setting (5ESS). When the 3Com tech set it, it stayed? Also the cause codes, timeslot mapping and blocking, and timeslot service configurations are not taking. We set them, save the settings to NVRAM, and reset the card and all the settings revert, BUT, when we restore from nvram all the settings get the correct values? Any ideas would be appreciated. We are running 4.1.59 on the ARC and 2.0.81 on the DSPs. The NMC is running 5.6.2. This is a new chassis. Samuel S. Lowe Director, Data Services UniversalCom, Inc. slowe(a)universalcom.net - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

RE: (usr-tc) USR-TC chassis dying. Help!
by Brian Elfert 10 Dec '99

10 Dec '99

On Wed, 8 Dec 1999, Marshall Morgan wrote: > I would reboot the Netserver and see if that fixes the problem as it > sounds like a packet bus issue (t1 passes the call to the modem but the > modem cannot talk to the netserver). I did power cycle the whole unit last night to no avail. I did have like 12 calls up while other modems were turning red and giving dead air. I soft busied both T1s, but the remaining calls all ended up getting dropped with Lost-Carrier within 30 minutes. According to Radius logs, 5 of the calls dropped within 2 seconds. One person did call and complain about being dropped. After reading your message, I decided to check the modem assignments in the Netserver. The Netserver seems to think modems are assigned to slot 1. I think I'll try wiping the NVRAM in the Netserver and reconfiguring it. Brian - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

5 6

Re: (usr-tc) TCM Crashing - Help
by Steve Valiunas 10 Dec '99

10 Dec '99

Can you provide code versions and more specifics about any parameters you are grabbing in Performance Monitor (if you can get that far)? Steve Valiunas "Brian Gordon" <administrator(a)westelcom.com> on 12/08/99 10:00:36 PM Please respond to usr-tc(a)lists.xmission.com Sent by: "Brian Gordon" <administrator(a)westelcom.com> To: usr-tc(a)lists.xmission.com cc: (Steve Valiunas/MW/US/3Com) Subject: (usr-tc) TCM Crashing - Help What is going on with TCM now? It seems like whenever I install this on a fresh install of Windows NT it has all sorts of problems. It doesn't crash until I go into Performance Menu. Anyone else have this sort of experience? Never had the problem with win95/98 just NT. Brian Gordon Network Administrator Westelcom Internet administrator(a)westelcom.com - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

4 3