- montgomery_boats - mailman.xmission.com

Cockpit drains
by Wilson Frye 31 Jan '17

31 Jan '17

All, My M-17 (#359) cockpit drains are routed from the fuel tank locker through hoses internal to the boat to exit underwater through aluminum through hull stub connections. The aluminum stubs are a bit corroded, but don’t appear to be unsafe, but I am considering modification to avoid the inevitable problem of leakage due to the corrosion. More recent builds have the cockpit drains located in the transom, about 3 inches above the waterline, about a foot port and starboard of centerline, through what appear to be Marelon thru hulls. On the MSOG site, Bob Eeg mentions using Whale check valves to prevent back flow into the fuel tank locker. Has anyone done this modification, and if so, are there “lessons learned” that I should be aware of? I’ve a bit of experience doing fiberglass hull repair (closing holes and openings that are no longer needed due to configuration changes with West System. Thanks. Will

3 6

M-Boats: Cockpit drains
by Thomas Buzzi 31 Jan '17

31 Jan '17

On my Monty 17 #258 I added 2- 1.5 inch cockpit drains modeled in location after the ones installed on new Monties being built. I was going to go with some sort of backflow check but found them to be expensive so used a Blue Sea system flapper valve that screws over the transom end of the drain pipe after it pierces the transom above the waterline. They are inexpensive and have served well to stop water from sluicing back into the cockpit. I made sure they exited above the waterline to avoid water flowing back into the cockpit when the cockpit had three or four people in it. I was able to find regular PVC fittings for the 1 1/2 diameter pipe that were a slip type on one end while the other end was threaded for a 1 1/2 inch pipe thread. This allowed screwing a female PVC fitting over the male thread as a nut to hold the fitting in place both at the aft end of the cockpit and the outside of the transom. For the actual pipe I used 1 1/2 in flexible pipe like that used to plumb spas. This allowed me bend the pipe into place inside the hull between the transom and the backside of the cockpit aft wall once I had glued the fittings to both ends of it. Once installed it was a simple matter to make a gasket of #400 Adhesive and screw the female ends onto the male fittings. I had already cut off most of the female end fittings so neither stuck out into the cockpit enough to catch an ankle and to also allow a decent sized flat surface to screw the Blue Sea flapper valve on the outside of the transom. Several pictures in the Msog photosite show the finished product. I was also leery of the stock aluminum sleeves that were fiberglassed into the boat to receive both ends of the original cockpit drain so I glassed them further into the boat so that the new drain hole clamps onto fiberglass instead of only to aluminum. That way electrolysis won't eventually corrode a hole in that aluminum and flood the boat. Currently I have my boat moored in a marina. Have fun, putter on the boat, go sailing. "AS-IS", Monty 17 #258 Tom B

1 0

Re: M_Boats: M17 Spar Identification
by Dan Farrell 31 Jan '17

31 Jan '17

Thanks for the info, Bob. Looks very close indeed. Dan Farrell M17 #301 Bob Eeg <montgomeryboats(a)hotmail.com> wrote: >Hi Dan > >Yeah, the mast in a photo is my build. That rig is mine. > >I use Dwyer DM-6 masts which are close to your mast. > >It used to be called the Sparcraft 106. > >https://www.dwyermast.com/items.asp?cat1ID=20&cat1Name=Masts&familyID=40&fa… > >Same for the masthead. > >Be well >Bob >Montgomery Boats >949-489-8227 > >Sent from my iPad > >On Jan 30, 2017, at 7:04 PM, Dan Farrell <msog(a)danf.us<mailto:msog@danf.us>> wrote: > >Thanks very much. Looks more recent than some of my hardware, but the mast section looks right. > >Dan Farrell >M17 #301 > >"Keith R. Martin" <keith.richard.martin(a)gmail.com<mailto:keith.richard.martin@gmail.com>> wrote: > >Hello danf.us<http://danf.us> > >Check this link out for M17 specifications.. > >http://www.msogphotosite.com/Scripts/Information/downloaddocument.php?id=199 > >Cheers > >Keith > >*Keith R. Martin, P.Eng.* > > >*Burnaby, B.C. CanadaSerenity, M17 #353* > > > >On 30 January 2017 at 17:42, <msog(a)danf.us<mailto:msog@danf.us>> wrote: > >HI All, > >I have M17 #301. I'm trying to identify the spars used on the boat, and >finding it less than trivial. Does anyone on this mailing list have any >hints or guesses? > >I've been idly considering the standing rigging, thinking about where and >how I would add something like spinnaker pole parts ( ring/track & topping >lift ), and thought of my warped old boom, and started browsing and >guessing, but curious what kind of parts I might be able to find that were >made for the spars. I haven't found anything that specifically says what >spars were used, and I haven't stumbled across any parts that looked >particularly like what I have onboard. >

1 0

Re: M_Boats: M17 Spar Identification
by Dan Farrell 31 Jan '17

31 Jan '17

Thanks for that history, Jerry. It's nice to get real names, even if they're no longer available. Also helps explain why even production boat lines have many small irregularities over the years. Thanks for a great boat! Dan Farrell M17 #301 jerry(a)jerrymontgomery.org wrote: >#301 would be one of mine, and would be a Sparcraft 104 section. Early in >my career I bought interest in the extrusion die, after Sparcraft had gone >out of business, and bought the masts directly from the extruder, 1,000 >pounds at a time. Later, when Vagabond came out with a 17, Ron Holder and I >made purchases together, buying 3,000 lbs, which got a better price. That's >when I changed the length of the 17 mast from 21' 2 1/2" to 21'4"; Ron's >boat had a fractional rig, which needs a longer mast, so we compromised. >Now you know! > >-----Original Message----- >From: msog(a)danf.us >Sent: Monday, January 30, 2017 5:42 PM >To: montgomery_boats(a)mailman.xmission.com >Subject: M_Boats: M17 Spar Identification > >HI All, > >I have M17 #301. I'm trying to identify the spars used on the boat, and >finding it less than trivial. Does anyone on this mailing list have any >hints or guesses? > >I've been idly considering the standing rigging, thinking about where and >how I would add something like spinnaker pole parts ( ring/track & topping >lift ), and thought of my warped old boom, and started browsing and >guessing, but curious what kind of parts I might be able to find that were >made for the spars. I haven't found anything that specifically says what >spars were used, and I haven't stumbled across any parts that looked >particularly like what I have onboard. > >

1 0

Re: M_Boats: Cockpit drains
by Dan Farrell 31 Jan '17

31 Jan '17

Hmm, interesting. Maybe I could add one of these to stop water getting into the cockpit on higher wind days. They look inexpensive. http://www.whalepumps.com/marine/product-accessories.aspx?Category_ID=10000… Dan Farrell M17 #301 Wilson Frye <fryewe(a)mac.com> wrote: >All, > >My M-17 (#359) cockpit drains are routed from the fuel tank locker through hoses internal to the boat to exit underwater through aluminum through hull stub connections. The aluminum stubs are a bit corroded, but don’t appear to be unsafe, but I am considering modification to avoid the inevitable problem of leakage due to the corrosion. > >More recent builds have the cockpit drains located in the transom, about 3 inches above the waterline, about a foot port and starboard of centerline, through what appear to be Marelon thru hulls. On the MSOG site, Bob Eeg mentions using Whale check valves to prevent back flow into the fuel tank locker. > >Has anyone done this modification, and if so, are there “lessons learned” that I should be aware of? I’ve a bit of experience doing fiberglass hull repair (closing holes and openings that are no longer needed due to configuration changes with West System. > >Thanks. >Will

1 0

M17 Spar Identification
by msog＠danf.us 30 Jan '17

30 Jan '17

HI All, I have M17 #301. I'm trying to identify the spars used on the boat, and finding it less than trivial. Does anyone on this mailing list have any hints or guesses? I've been idly considering the standing rigging, thinking about where and how I would add something like spinnaker pole parts ( ring/track & topping lift ), and thought of my warped old boom, and started browsing and guessing, but curious what kind of parts I might be able to find that were made for the spars. I haven't found anything that specifically says what spars were used, and I haven't stumbled across any parts that looked particularly like what I have onboard.

5 4

Re: M_Boats: M17 Spar Identification
by Dan Farrell 30 Jan '17

30 Jan '17

Thanks Dave. I'm wondering about boom and traveller. Both are warped from strenuous use. Maybe the boom could be replaced or straightened with a jack and frame or something. The traveller I was considering replacing. Both seem like fairly easy parts to isolate from the rest of the rigging. Dan Farrell M17 #301 Dave Scobie <scoobscobie(a)gmail.com> wrote: >The details on John's list on the msogphotosite that Keith linked are close >enough to the spar that is on your 17 danf. > >The spars at Jerry used are no longer made. One of many boat component >manufacturers that are no longer around. > >If you need assistance on the specific parts let me know. > > >:: Dave Scobie >:: M17 #375 SWEET PEA - https://m17-375.com/ > >On Jan 30, 2017 6:46 PM, "Keith R. Martin" <keith.richard.martin(a)gmail.com> >wrote: > >Hello danf.us > >Check this link out for M17 specifications.. > >http://www.msogphotosite.com/Scripts/Information/downloaddocument.php?id=199 > >Cheers > >Keith > >*Keith R. Martin, P.Eng.* > > >*Burnaby, B.C. CanadaSerenity, M17 #353* > > > >On 30 January 2017 at 17:42, <msog(a)danf.us> wrote: > >> HI All, >> >> I have M17 #301. I'm trying to identify the spars used on the boat, and >> finding it less than trivial. Does anyone on this mailing list have any >> hints or guesses? >> >> I've been idly considering the standing rigging, thinking about where and >> how I would add something like spinnaker pole parts ( ring/track & topping >> lift ), and thought of my warped old boom, and started browsing and >> guessing, but curious what kind of parts I might be able to find that were >> made for the spars. I haven't found anything that specifically says what >> spars were used, and I haven't stumbled across any parts that looked >> particularly like what I have onboard. >>

1 0

Re: M_Boats: M17 Spar Identification
by Dan Farrell 30 Jan '17

30 Jan '17

Thanks very much. Looks more recent than some of my hardware, but the mast section looks right. Dan Farrell M17 #301 "Keith R. Martin" <keith.richard.martin(a)gmail.com> wrote: >Hello danf.us > >Check this link out for M17 specifications.. > >http://www.msogphotosite.com/Scripts/Information/downloaddocument.php?id=199 > >Cheers > >Keith > >*Keith R. Martin, P.Eng.* > > >*Burnaby, B.C. CanadaSerenity, M17 #353* > > > >On 30 January 2017 at 17:42, <msog(a)danf.us> wrote: > >> HI All, >> >> I have M17 #301. I'm trying to identify the spars used on the boat, and >> finding it less than trivial. Does anyone on this mailing list have any >> hints or guesses? >> >> I've been idly considering the standing rigging, thinking about where and >> how I would add something like spinnaker pole parts ( ring/track & topping >> lift ), and thought of my warped old boom, and started browsing and >> guessing, but curious what kind of parts I might be able to find that were >> made for the spars. I haven't found anything that specifically says what >> spars were used, and I haven't stumbled across any parts that looked >> particularly like what I have onboard. >>

2 1

Sailing with SoCal Potter Yachters
by Blair Ashworth 30 Jan '17

30 Jan '17

Went sailing yesterday in Dana Point with the SoCal Potter Yachters. Had a great time. Got to visit with Bob Eeg and a fellow Monty 15 sailor, Fu-Shing Pan who sails M15 #120. Here is a short video I posted on Youtube if you are interested. https://youtu.be/CvwvG0wRIXg Blair M15 #126

5 4

Re: M_Boats: Intentional Capsize for M15
by Blair Ashworth 29 Jan '17

29 Jan '17

Thanks again everyone. Great replies and info. Also, so glad that Bert was safely helped back to the marina. At any age, that would be a frightening encounter! My M15 still has the foam blocks and both of my cockpit lockers have the original pans - all sealed, no way for water to get into the hull. So I feel very safe in my pocket cruiser! Had a great sail in Dana Point yesterday with the So. Cal. Potters. I'll shoot a link out later to a quick youtube video I'm uploading soon. Blair M15 #126

3 2