- USR-TC - mailman.xmission.com

Weekly 3Com Hiper Blowout POST!!
by sky1 12 Jun '03

12 Jun '03

Still have fully loaded Hiper chassis in stock!!! $2750.00 each Configured as follows: (14) Hiper DSP T-1 card sets (2) Hiper ARC 128Mb Version card sets (1) Hiper NMC (2) 130 Amp AC power supplies (1) Blue Labeled chassis w/ integrated fan assembly I also have a few more Hiper NMC's that I am parting out. Have around 10 of them I'd sell for $450.00 each Hiper DSP cards T-1 Version $175.00 each Hiper ARC sets 128Mb Version $100.00 each Thanks for your time, Shannan Young SouthWest Data Technology, Inc. 972-739-7010 972-739-7013 (Fax) sky1(a)airmail.net www.swdt.com

1 0

NMC memory in NETServer
by alex 10 Jun '03

10 Jun '03

Is it possible to place NMC's DRAM memory card into NETServer PRI? NMC is old NMC_CLK. Thanks, Alex

1 0

TCS 4.5 vs. 4.7
by Mike Wilker 09 Jun '03

09 Jun '03

Is there any difference in the modem code/features between the lastest 4.5 and 4.7 DSP firmware? Mike Wilker Director of Network Operations Tiger Communications & Local Link

1 0

Release notes
by Mike Wilker 09 Jun '03

09 Jun '03

Are release notes no longer being given for service releases of TC1000 software? A couple of years back they used to be there and they were very helpful. Mike Wilker Director of Network Operations Tiger Communications & Local Link

1 0

2 NETServers in one chassis?
by alex 04 Jun '03

04 Jun '03

Is it possible to install 2 NETServers in one chassis with Quad analog modems? If yes what/how do I have to configure on this netservers and quads (NETServer Card V.34/ISDN with Frame Relay V3.8.1)?

1 0

HiperARC IP terminal service
by Gen Camiling 04 Jun '03

04 Jun '03

Hi All, I want to use the HARCs as a replacement for some old,EOLd IBM Terminal servers. I plan to use IP Terminal Service feature of the HARC, my problem though is it keeps on asking for a login/password combo prior to getting connected. Is there a workaround wherein once the dialin client calls will be automatically connected to the HARC and gets a prompt (Hiper>>) from which they can TELNET to other hosts? -- Best regards, Gen =================================== Gener R. Camiling Chief Technical Officer International Micro Village, Inc. http://www.imvi.com.ph ===================================

2 1

Question about Quad Modems D/A and outdials...
by Todd Williams 03 Jun '03

03 Jun '03

Hello, We're using a TC1000 chassis with some Quad Modem digital/analog v.90 cards as modems (via RS-232 card) dialing out over PRI for a legacy outdial application which dials out to a variety of ISDN and POTS modems. We seem to be having some strange issues when dialing some of the old Motorola Codex 33.6K modems. Does anyone have any experience in this area, or have you seen any compatibility issues between these modems (or others)? Thanks in advance for any assistance or advice you might be able to offer. Thanks, Todd

3 2

NetServer PRI and Callback
by alex 31 May '03

31 May '03

How is it possible to do callback on Netserver PRI(see version below) with Quad modems on analog lines using radius? I want some users to have callback (framed) service, and others to have standart dial-in. Do I have to upgrade soft? Netserver version>> U.S. Robotics Total Control (tm) NETServer Card V.34/ISDN with Frame Relay V3.8.1 Build date: Aug 11 1998 Build time: 13:49:21 Network Interface Card: Ethernet (24) ISDN Interface Card : MUNICH32 (4) Packet Bus Circuit : Enhanced

1 0

Hiper NMC in 45A chassis??
by Randy McMillan 30 May '03

30 May '03

I am in a slow process of updating my chassis from quads to dsp's, etc. Does anyone know if the hiper NMC would work in an old 45A chassis or what issues there might be? I would only have about 6 dsp's Would there be any issues with TCS versions and the old chassis? . Or should I break down and get a TC1000 chassis. Thanks. Randy McMillan PacInfo

1 0

RE: [USR-TC] Error Trying to change Switch Type in TCM
by Adam Barnhill 30 May '03

30 May '03

Seems to me that it occurs most often when dealing with TCS 4.3 and TCS 4.2 DSPs in the same chassis with ARC/NMC at TCS4.3 Not to mention tcs4.5 and tcs4.3 Chassis, that's terrible. One thing to try might be to set it in console. Things just seem to work better when issued from command line. The following will show you how to setup remote console access to the HiperDSP on Slot 1. HiperARC> add modem_group DSP1 interface SLOT:1/CON:1 add network service DSP1 server_type telnetd socket 6011 data auth=off,service_type=dialout,modem_group="DSP1" Telnet to IP of that ARC tcp port 6011 and then enter console password > (if using PRI, message oriented) Chdev span Set swtype DMS100 Cmd svspcfg (if using robbed bit T1) Chdev span Set sigmode msg (unless you are using PRI, you will have to do this before changing switch type) Set swtype DMS100 Set sigmode robbit Cmd svspcfg Close Telnet session. HiperARC> Disable Network Service DSP1 (or for good measure you can then delete it also) Delete Network Service DSP1 -- Adam Barnhill Support Engineer, TotallyFabricated.com Information Technology Engineer, Poplar Bluff Internet, Inc. / Semo.net P.O. Box 190 | Poplar Bluff, MO 63902 | 573.686.9114, <http://www.semo.net/> Home of TotallyFabricated.com the creators of Total Scrutinizer -----Original Message----- From: usr-tc-bounces(a)mailman.xmission.com [mailto:usr-tc-bounces@mailman.xmission.com] On Behalf Of Joel - Fox Computers Sent: Thursday, May 29, 2003 11:11 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: RE: [USR-TC] Error Trying to change Switch Type in TCM Didn't see if anyone else helped on this, but I thought I'd share my thoughts - This has happened to me before. One thing may be if you are trying to change a bunch of DSP's all at once. Do fewer at a time or even one at a time and you may not get the error. Another thing - if I remember correctly this happened once or twice when the firmware between the cards was incompatible, for example 3.5.109 on the DSP's and 6.x on an old 486 NMC (just an example, don't know for sure if these were the versions) Hope this helps, thanks, Joel -----Original Message----- From: Cindy Smith [mailto:cindyo@ktc.com] Sent: Wednesday, May 28, 2003 10:08 AM To: USR-TC(a)mailman.xmission.com Subject: [USR-TC] Error Trying to change Switch Type in TCM Hi, I am using Total Control Manager Windows Version 8.2.6 When every I try to change the Switch type on a HiperDSP card using TCM Windows, I get a Generic Error concerning the Switch Type OID. Does anyone know a work around for this. I am trying to change the switch type to DMS 100 Thanks in Advance, --Cindy -- ----------------------------- Cindy Smith KTC iNet 896-1111 SysAdmin ----------------------------- _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0