- USR-TC - mailman.xmission.com

Looking for Hiper DSP E1 sets
by Russell Newberry 10 Aug '04

10 Aug '04

Hi Guys, I'm looking to pick up qty 14 Hiper DSP E1 Sets. Anybody looking to sell? Let me know whatcha got! Also, I have the following for sale: Qty 1 333 NMC II set Qty 2 Hiper NMC sets Qty 10 96-port Multispan Sets Looking for offers on the above. Thanks, Russell Newberry ==================== Maxis Technologies, Inc 433 W. Wilshire Blvd. Ste 2B Oklahoma City, OK 73116 Voice: 1-800-79-MAXIS Int'l: 1-405-842-3331 FAX: 1-405-841-7882 find us on the web at www.maxistech.net email to: russell(a)maxistech.net AOL IM "RUSSELLatMAXIS"

1 0

(no subject)
by Scot 09 Aug '04

09 Aug '04

1 0

Help: Dropping packets for not-in-use IPs
by David E. Smith 06 Aug '04

06 Aug '04

I've got a strange thing happening with one of my USR HiperArcs. Someone, somewhere, is trying to DDOS a dialup customer's IP address. This is annoying enough, but that IP isn't even in use right now. So the packets just keep bouncing back and forth around my office. Traceroutes just keep going back'n'forth between the USR and its gateway, each of which thinks the other is the right place for this packet to be. Is there a way to convince the HiperArc that it's the "final" destination for all the addresses in its IP pools, and to drop packets destined for IPs in that pool that aren't connected right now? (If this is too vague, let me know and I'll gladly provide any extra details needed.) Thanks! David Smith MVN.net

3 3

DSP Multispan sets, looking for offers
by Russell Newberry 28 Jul '04

28 Jul '04

Hello everyone, Looking for offers on: Qty 10 DSP 96-port Multispan sets Qty 3 Hiper NMC sets Qty 5 130amp AC Power Supply sets Qty 50 Edgeserver cards Qty 20 Hiper ARC sets (New in Box) Let me know if you're interested in ANY or ALL of the above! Thanks, Russell Newberry ==================== Maxis Technologies, Inc 433 W. Wilshire Blvd. Ste 2B Oklahoma City, OK 73116 Voice: 1-800-79-MAXIS Int'l: 1-405-842-3331 FAX: 1-405-841-7882 find us on the web at www.maxistech.net email to: russell(a)maxistech.net AOL IM "RUSSELLatMAXIS"

1 0

Quad modem problem
by Sergio Gonzalez 23 Jul '04

23 Jul '04

Hello: I've been experiencing problems with quad modems (analog/digital) and dual pri card. I already set up the Dual Pri. The incomming calls routing works fine (round robin). The problem is that any modem do the handshaking "sound". They just answer the call (like picking up the phone with no one talks). What should be the problem? Thanks a lot in advance. Sergio Alejandro Gonzalez Director Operativo Network and Services Field Manager SkyNet de Colombia. Calle 100 No. 8A-55 Of. 711 Bogota, Cundinamarca Colombia, South America. Tel: 57 (+1) 6 422 020 Cel: 57 (+3)/(03315) 3551034 Pager: 5405555, 3469999 Cod 2010

1 0

TCS recommendation?
by S H A N 16 Jul '04

16 Jul '04

hi, i am intending to buy Hiper DSP Multispan cards together with ARC2 and NMC333. i would like to have list member's recommendation on which TCS should i buy? 4.5 or 4.7? (or if there any other recommendations?) thanks & rgds, -- To follow the path: look to the master, follow the master, walk with the master, see through the master, become the master.

2 1

RE: [USR-TC] DSP Out of Service Problem
by Joel - Fox Computers 15 Jul '04

15 Jul '04

Todd, Thanks, but that's not the problem. AFTER the reset, once the card is back up, they go idle, and then go out of service and stay out of service. - Joel -----Original Message----- From: Todd Bertolozzi [mailto:berto@core.com] Sent: Thursday, July 15, 2004 3:10 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] DSP Out of Service Problem That seems kinda normal to me Joel. You've got a dsp with a pri plugged in and the timeslots are idle....you reset the dsp causing the d channel to go down and hence the timeslots go down. It varies on the code you're running, and the particular config options. Sometimes you don't see anything. I'm running older code then that and when I reset a dsp my timeslot go from idle to something like "doesn't match anything". You're timeslots definitely aren't idle when you reset the dsp b/c you're resetting the ds1. Todd ----- Original Message ----- From: "Joel - Fox Computers" <jfox(a)foxcomputers.com> To: "Discussion relating to the 3Com/US Robotics Total Control modemsystems." <usr-tc(a)mailman.xmission.com> Sent: Thursday, July 15, 2004 1:29 PM Subject: [USR-TC] DSP Out of Service Problem > Got a wierd problem I hope someone can help with. The chassis has 2 Hiper ARCs (5.3.110) and 6 Hiper DSPs (3.5.109). We're running PRI's to them. The Hiper ARC "list chassis" shows the correct cards, the ARC in slot 15 owns all the DSPs, the ARC in slot 16 owns nothing. NMC Chassis Awareness is disabled on both Hiper ARCs, they are set up statically. > > On a DSP with no PRI plugged in, I see something like "DS0 Timeslot Idle", whatever is normal. With a PRI plugged in, after a hardware reset on the DSP, you see the same thing. Then somewhere between 5 and 60 seconds after the reset, the status goes to "DS0 Local Out of Service" on all the timeslots. > > The DSPs have been reset to factory Defaults, with the only change being the Switch Type, which is set to NI2, of course followed by saving the setting and resetting the card. I know this setting is correct, I can unplug the PRI from the DSP card and plug it into a PortMaster (which is configured for a plain PRI with NI2 as the switch) and it links up and takes calls right away. > > I'm reasonable certain it's not the Hiper ARC, because we did at one point have half the DSPs owned by each ARC and had the same result. > > Pulling my hair out over this one - any suggestions? Any idea what I'm overlooking or not checking? Any suggestion would be appreciated. > > Thanks, > > Joel > > > > > > > > > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

RE: [USR-TC] DSP Out of Service Problem
by Joel - Fox Computers 15 Jul '04

15 Jul '04

Thanks, hadn't tried that - I'll give it a try and see. THANKS! Joel -----Original Message----- From: Adam Barnhill [mailto:adam@semo.net] Sent: Thursday, July 15, 2004 1:24 PM To: 'Discussion relating to the 3Com/US Robotics Total Controlmodemsystems.' Subject: RE: [USR-TC] DSP Out of Service Problem Have tried this article? Question Total Control HiPer DSP - DSO's intermittently go into LOOS Incorrect modem command (AT%R) settings written into T1/E1 span settings Answer Please take on of the following actions: 1. After flash updating code and rebooting HiPer DSP card, default the T1/E1 settings from factory default within TCM. Configure span per telco requirements then save configuration again into NVRAM. Or 2. Log into HiPer DSP console either via reverse telnet from gateway card or serial connection and enter the following commands: chdev mdm 255 <Enter> at%r1=3%r2=10%r3=1%r4=3%r5=2%r6=1&r7=4&w <Enter> wait for "OK" prompt. If none seen enter ATE1V1Q0 <Enter> and repeat above command at%r? <Enter> display should read - Per-R parameters 1:3 2:10 3:1 4:3 5:2 6:1 7:4 chdev span <Enter> cmd sinserv <Enter> dis ats <Enter> (all DSO's should now be idle) cmd svspcfg <Enter> -----Original Message----- From: usr-tc-bounces+adam=semo.net(a)mailman.xmission.com [mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf Of Joel - Fox Computers Sent: Thursday, July 15, 2004 12:29 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: [USR-TC] DSP Out of Service Problem Importance: High Got a wierd problem I hope someone can help with. The chassis has 2 Hiper ARCs (5.3.110) and 6 Hiper DSPs (3.5.109). We're running PRI's to them. The Hiper ARC "list chassis" shows the correct cards, the ARC in slot 15 owns all the DSPs, the ARC in slot 16 owns nothing. NMC Chassis Awareness is disabled on both Hiper ARCs, they are set up statically. On a DSP with no PRI plugged in, I see something like "DS0 Timeslot Idle", whatever is normal. With a PRI plugged in, after a hardware reset on the DSP, you see the same thing. Then somewhere between 5 and 60 seconds after the reset, the status goes to "DS0 Local Out of Service" on all the timeslots. The DSPs have been reset to factory Defaults, with the only change being the Switch Type, which is set to NI2, of course followed by saving the setting and resetting the card. I know this setting is correct, I can unplug the PRI from the DSP card and plug it into a PortMaster (which is configured for a plain PRI with NI2 as the switch) and it links up and takes calls right away. I'm reasonable certain it's not the Hiper ARC, because we did at one point have half the DSPs owned by each ARC and had the same result. Pulling my hair out over this one - any suggestions? Any idea what I'm overlooking or not checking? Any suggestion would be appreciated. Thanks, Joel _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

DSP Out of Service Problem
by Joel - Fox Computers 15 Jul '04

15 Jul '04

Got a wierd problem I hope someone can help with. The chassis has 2 Hiper ARCs (5.3.110) and 6 Hiper DSPs (3.5.109). We're running PRI's to them. The Hiper ARC "list chassis" shows the correct cards, the ARC in slot 15 owns all the DSPs, the ARC in slot 16 owns nothing. NMC Chassis Awareness is disabled on both Hiper ARCs, they are set up statically. On a DSP with no PRI plugged in, I see something like "DS0 Timeslot Idle", whatever is normal. With a PRI plugged in, after a hardware reset on the DSP, you see the same thing. Then somewhere between 5 and 60 seconds after the reset, the status goes to "DS0 Local Out of Service" on all the timeslots. The DSPs have been reset to factory Defaults, with the only change being the Switch Type, which is set to NI2, of course followed by saving the setting and resetting the card. I know this setting is correct, I can unplug the PRI from the DSP card and plug it into a PortMaster (which is configured for a plain PRI with NI2 as the switch) and it links up and takes calls right away. I'm reasonable certain it's not the Hiper ARC, because we did at one point have half the DSPs owned by each ARC and had the same result. Pulling my hair out over this one - any suggestions? Any idea what I'm overlooking or not checking? Any suggestion would be appreciated. Thanks, Joel

3 2

Does anyone have a good virus filtesr they would be willing to share
by Cyrus Smith 15 Jul '04

15 Jul '04

Hi, I am looking for an example of a good "in." and "out". filter for the hiper arc. Does anyone have filters they would be willing to share? Thank you!

2 1