- USR-TC - mailman.xmission.com

(usr-tc) Dual PRI CARD
by Lou Bernstein 19 Jun '00

19 Jun '00

Hi All I need a little help here. I have a TC with a HIPER ARC, several HIPER DSP cards, some Quad Digital cards and a Dual PRI-Card NAC. I have been running for a long time with the HIPER DSP cards without problems. I now need to run the Quad cards and can not seem to get the Dual PRI card to work(it did work at one time). The PRI line is coming from a Lucent Definity 3G switch and works fine with the Hiper DSP cards. When I connect the PRI line to the Dual PRI card all I get is a busy signal, the link does show that it is up and there are no alarms.. The Dual PRI card has the following configuration Framing Mode ds1esf Line Coding b8zs Response to remote loopback ignore Auto Busy disabled Dial In Address No Address Dial-in/Dial-out Signal WINK ACK WINK Enabled Dial in Trunk type E&M TYPE II The settings above are set similarly on the Hiper DSP card. Any help would appreciated. Thanks in advance LOU - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

(usr-tc) And you thought you were frustrated with 3COM
by Scot Desort 19 Jun '00

19 Jun '00

Is anyone else here on the Ascend users list? Whew - there are some VERY angry people on that list. While I have never had to go to Lucent for support, what these people are describing makes things at 3COM look bright and sunny. Top-tier engineering support calls being ignored. Technicians who don't know the products. RMA and warranty claims not being addressed. It's worse than any complaints I've seen on the 3COM list. I *was* considering picking up some Ascend gear to compliment my 3COM stuff, but I am seriously reconsidering that. So, what's left - Ci$co? Are they the only company that provides the kind of support ISP's need? They usually seem to do most everything right. I don't know -- think I'll stick it out with 3COM and see if all of the newly found resources available from the drop of their switches actually *does* go into the ISP/Carrier division. -- Scot - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

11 11

(usr-tc) Config for Dual BRI Cisco to TC
by Verreault, John 19 Jun '00

19 Jun '00

I am trying to get a cisco 4000 with 2 BRI interfaces to connect to a Total Control Chassis. (I am not sure if you can MPP over both BRI's, if not I would settle for MPP for each BRI and load balance over the 2 multilinked BRI's) I am having some problems with the second BRI. I cannot get a stable connection. I am assigning the BRI interface a static IP and specifying the route with radius. Should the second interface have the same static IP address or a different one. I have tried several variations without success. Does anyone have a sample config they can send me or point me in the right direction. Thanks John Verreault AEI Internet john(a)aei.ca <mailto:john@aei.ca> 514/284-4452 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

(usr-tc) What HiperDSP code works best with Lucent Winmodem?
by peter.olson＠chi.frb.org 17 Jun '00

17 Jun '00

Hello, We are having trouble connecting the new IBM 600x which bundles a Lucent winmode (yuck) to our TC /HiperDSP. On clean phone lines, the authentication terminal window will show a ton of garbage text. I have seen this before when we had X2 modems dialing our V.90 patched DSP's, so I am not surprised. Because we using Microsoft RAS on Egdeserver Pro 2.1.2 drivers (yuck again, I know), we are unable to upgrade the DSP's to the 2.0.x level firmware. The firmware we do have is 1.0.59 on two DSP's and 1.0.43 on two others. The problem seems worse on 1.0.43 DSP's. Does anyone out there know which level is best, or elimates this lucent winmodem problem? The 2.6 Edgeserver drivers which run on SP6a will support the 2.0.x DSP's, but these are still in Beta. I am not going to install 2.5 Edgeserver drivers if I can avoid it. The install is ugly. Thanks In advance, --Peter

2 1

(usr-tc) FS: USR Hiper Cards
by ISP-NetworkHardware.com 16 Jun '00

16 Jun '00

In stock... 2- Hiper NMC $1000 2- Hiper ARC $1900 or BO 1- Hiper DSP, No nic $3000 Also have: 4- USR Viper DSL Modems $500 1- USR Viper DSL (ALC) (Nic/Nac) $600 Lots of USR available...Inquire if needed. Netservers, MP, Total Controls, Parts =+= =+= =+= =+= =+= =+= =+= =+= =+= =+= =+= =+= =+= =+= =+= =+= =+= =+= Steve Rivera (VP) - w-732-833-2111 / c-732-433-5890 24Hr ICQ# 75229638 Email Page 7324335890(a)page.nextel.com (start message with YOUR email address) Worldwide Provider of Network Hardware Since 1981. http://www.wrca.net or http://www.ISP-NetworkHardware.com Cisco, Ascend,USR,Adtran, Kentrox,Livingston, Microcom,Computone,BayNetworks, Verilink,IBM,Motorola,UDS,Codex,ATT/Paradyne,Hayes,Racal,GDC,Telebit,MultiTech, Sync/Tylink,Wellfleet,,Black Box,Micom & More - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) USR Total Control MP/16 v.34 modems
by Jamie Orzechowski 16 Jun '00

16 Jun '00

For Sale USR Total Control MP/16 v.34 modems http://cgi.ebay.com/aw-cgi/eBayISAPI.dll?ViewItem&item=359752097 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Isdn callback with the HARC
by Ernie Pritchard 15 Jun '00

15 Jun '00

Is anyone doing ISDN callback with the harc? I have been trying to get this working with both a cisco 766 and a pipeline 75. I was unable to get the harc to do anything with the dialback configuration setup in the radius server <usr SA ver 6.0.8>, after fooling around with the config in the HARC I was able to get the arc to callback. Im not sure if it is calling the router analog or isdn since its not working. Im running 4.2.32 on the arc and heres an example of the configuration. set modem_group all access two_way add user <username> password <password> type network,callback set user <username> callback_type static phone_number xxxxxxx set network user <username> ip remote_ip_address xxx.xxx.xxx.xxx/xx With this configuration the remote user hits the chassis and then gets disconnected. Ive spoken with support at 3com and the tech said that when the chassis calls back it does not auth with the remote side, this just sounds a little odd. Thanks in Advance, Ernie Pritchard InLine Connections - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) NTP time sync
by Scot Desort 15 Jun '00

15 Jun '00

I am trying to use an NTP server to sync my time on my Hiperarc. I issue the command set ntp primary_server x.x.x.x It accepts the command without error, but it doesn't sync the time. It stays the same as it was before I issued the command, and it doesn't match the time reported by the NTP server. Anything else I need to do to get this to work? -- Scot - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

5 5

(usr-tc) What is an LH/SH NIC ?
by Andy 15 Jun '00

15 Jun '00

Until now, our HDM T1 NICs have said under inventory "3COM T1/E1 HDM NIC". The last six we have installed from the 3COM Double-Play program say "3COM T1/E1 LH/SH NIC with Programmable Loopback Relays". I am assuming that LH/SH stands for "long haul / short haul", but what other changes are in the new NICs if any? Of note is that the matching NACs have product codes of 3C4, as opposed to all others installed with a product code of 10Q. All ideas and answers appreciated. Thanks --- Andy Dalrymple XMission Telecom Manager (6/15/00) - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

(usr-tc) OID for IdleTime?
by Jason Englander 15 Jun '00

15 Jun '00

I'm running the new HiPerARC code (and NMC, DSP) and I've seen "list sessions counters", but I'd sure love to be able to pull that by SNMP... Anyone know, if there is one, what the OID is for it? Numeric preferably. Jason -- Jason Englander <jason(a)interl.net> Systems Administrator - InterLink L.C. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

6 8