Hello everyone,
I'm getting the following error:
At 10:49:48, Facility "GWC Modem Driver", Lever "UNUSUAL"::GWCMDM_AL, slot: 11/mod:1 TAPI_OPEN failed, retrying
At 10:49:48, Facility "GWC Modem Driver", Lever "UNUSUAL"::GWCMDM_AL, slot: 11/mod:1 TAPI OPEN failed
At 10:49:48, Facility "GWC Modem Driver", Lever "UNUSUAL"::GWCMDM_AL, slot: 10/mod:4 TAPI_OPEN failed, retrying
At 10:49:48, Facility "GWC Modem Driver", Lever "UNUSUAL"::GWCMDM_AL, slot: 10/mod:4 TAPI OPEN failed
At 10:49:48, Facility "GWC Modem Driver", Lever "UNUSUAL"::GWCMDM_AL, slot: 10/mod:3 TAPI_OPEN failed, retrying
At 10:49:48, Facility "GWC Modem Driver", Lever "UNUSUAL"::GWCMDM_AL, slot: 10/mod:3 TAPI OPEN failed
At 10:49:48, Facility "GWC Modem Driver", Lever "UNUSUAL"::GWCMDM_AL, slot: 10/mod:2 TAPI_OPEN failed, retrying
At 10:49:48, Facility "GWC Modem Driver", Lever "UNUSUAL"::GWCMDM_AL, slot: 10/mod:2 TAPI OPEN failed
At 10:49:48, Facility "GWC Modem Driver", Lever "UNUSUAL"::GWCMDM_AL, slot: 10/mod:1 TAPI_OPEN failed, retrying
At 10:49:48, Facility "GWC Modem Driver", Lever "UNUSUAL"::GWCMDM_AL, slot: 10/mod:1 TAPI OPEN failed
...and so on.
Any ideas? This unit is running 15 Quad Analog/Digital Cards, a Hiper ARC, and NMC. Any help would be appreciated.
Thanks,
=========================
Russell Newberry
Maxis Technologies, Inc
433 West Wilshire Blvd.
Oklahoma City, OK 73116
AOL IM "RUSSELLatMAXIS"
e-mail: russell(a)maxistech.net
Phone: 1 (800) 79 MAXIS
International: 1 (405) 842-3331
Fax: 1 (405) 841-7882
http://www.maxistech.net
I know they are scarce, but I am hopeful.
Anyone have the Dual E1 nic.
Not Dual T1/E1 nic - for some reason never get the E1 circuit up with these
nics.
Let me know if you have any available I give you an offer and pay freight in.
Thanks
Also still buying 130A DC power sets (PSU/PSI)- paying $150ea
Let me know if you have any available.
Steve Rivera -WR Consultant Associates, Inc.
T: 732-833-2111 x102
IM: srivera711 www.wrca.net
Providing Network Hardware Since 1981.
I have two Dual T1/PRI cards that currently have 3.0.2 on them. I want to run
Channelized T1, and the install guide says that Channelized T1 is only
available with version 4.0 or later. How do I go about getting the software to
upgrade the card?
Thanks
Hatcher
Hey guys. These just in.
Pricing should be better for you guys that always contact me for E1 cards.
I know it doesnt compare to the T1/PRI's but the markets are different and
the T1's are all over the place where the E1's are much harder to locate.
1- TC1000 dual 130amp power, Hiper Arc, 4 E1 DSPs, 120 ports $2495
6- Hiper DSP E1 (30 channel modem card set) $500
Qty - Hiper DSP (24 channel modem cad set) $50ea
Qty TC1000 336 port T1/PRI Bundles $595
chassis, dual 130a, hnmc, 2x harc, 14-dsp
Qty Hiper ARC $125
In Stock. FOB: NJ
anything TC1000, I got it.
email for further info or parts you need that arent listed.
Steve Rivera -WR Consultant Associates, Inc.
T: 732-833-2111 x102
IM: srivera711 www.wrca.net
Providing Network Hardware Since 1981.
Immediate need for the following.
EdgeServer Carc AMD K-3 400 MHZ
PN# 69-001825-00
DC 130A power sets
PN# 69-001404-00
Steve Rivera -WR Consultant Associates, Inc.
T: 732-833-2111 x102
IM: srivera711 www.wrca.net
Providing Network Hardware Since 1981.
The USR TC's are capable of interfacing the modems over a telnet
connection, or so-called reverse telnet. UTstar describes how to get
this going, for instance:
<quote>
1. set modem s(port#) active
2. set s(port#) login network dialin device /dev/network
3. set s(port#) service_dev telnet 6001 (or any telnet port)
4. set s(port#) service_login telnet
5. save s(port#) or save all
6. reset s(port#) or reset all
>From the PC on the network
telnet x.x.x.x (netserver ip address) 6001
You can now type AT commands
</quote>
Connecting to the Netserver ('telnet x.x.x.x xxxx') works, but any typed
characters seem to end up in a black hole. Nothing is echoed back, and
typing stuff like ATIx etc triggers no response, either.
Dip switch tweaking needed? Ideas?
--
-o) Vegard Svanberg, CTO - XOIP Comm. (www.xoip.no)
/\\ Violgata 3A, N-1776 HALDEN, NORWAY
_\_v Phone: (+47) 69701802 | Fax: (+47) 69701801
We recently aquired two 3com/USR Total Control (network hub) with the
quad modem cards. Both units are equipped like this:
1 T1/PRI card (NIC: RS-232 + span 1 + span 2)
12 quad modem cards (digital, no NICs)
1 Netserver PRI card (NIC: RS-232 + ethernet 1 + ethernet 2)
1 NMC (NIC: RS-232/EIA561 (CH1+2) + BNC/AUI/ethernet)
Issue #1: On the Netserver PRI card, the RN/FL and LAN/TX leds are solid
red, always. In TCM, the NAC isn't recognized at all (question mark). We
tried to do a firmware upgrade, but pcsdl doesn't connect (all dip
switches are off). Sometimes, if we boot the rack while pcsdl is trying
to connect, the RN/FL will blink green about 10 times, then all the leds
are shut off. It seems to only happen after we've physically re-seated
the NAC/NIC, though. We try to flash it with li030421.sdl/li030534.nac.
This may of course be a hardware problem, but the problem is on two
totally separate units.
Issue #2: Because of #1, we wanted to try upgrading the NMC. We only
find <filename>.dmf files lying around, and TMC doesn't seem to like
that file extension (configuration->software download only seem to
accept .nac files).
Any clues? UTstar didn't even respond when we asked them about their
support rates/contracts. :/
--
-o) Vegard Svanberg, CTO - XOIP Comm. (www.xoip.no)
/\\ Violgata 3A, N-1776 HALDEN, NORWAY
_\_v Phone: (+47) 69701802 | Fax: (+47) 69701801
Hi!
some users were encountered carrier loss during or while connected.
with this, the usage w/ carrier loss encounter an overlap connection
becaue the ras was not able to send a termination request to the
radius. does anyone encounter with this kind of problem? pls advise.
thanks,
Looks to me like a bad NAC. I'd call support for part replacement.
-----Original Message-----
From: usr-tc-bounces+adam=semo.net(a)mailman.xmission.com
[mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf Of
Shahrooz Sharghi
Sent: Monday, March 07, 2005 12:39 PM
To: Discussion relating to the 3Com/US Robotics Total Control
modemsystems.
Subject: Re: [USR-TC] e1 pri dsp software download
it is exact respons from consol while booting:
!!----------> SDL2 for the PPC403 <------------!!
__ Enter Download Trigger __
Flash Image Has Valid CRC, Loading Image....
Diagnostic Power-Up Failure
Manufacturing Info -> 1AAA13M0
Mode/Env -> 1/0
Fault Code -> 0-142-540-1
Expected Data -> 00000096
Received Data -> 00000000
Text Message -> The Address is the DSP number that failed.-----
Original Message -----
From: "Adam Barnhill" <adam(a)semo.net>
To: "Discussion relating to the 3Com/US Robotics Total Control
modemsystems." <usr-tc(a)mailman.xmission.com>
Sent: Monday, March 07, 2005 9:14 PM
Subject: RE: [USR-TC] e1 pri dsp software download
> Do you have console access to it? If so plug in and watch the boot
> process. It should indicate what the error is. If you get a CRC error
> or corrupt firmware type error, use the aux port to upload new code.
> Plug in to the aux port with 115200 8 n 1, then reseat the front.
> After a few moments you should get a prompt, at which time you will
> need to input the upload command. I believe this is AT{Z1}, but I may
> be mistaken. Once it is uploaded properly, you'll need to switch back
> to the console port at 9600. If it's not fixed, you should get a
> different error. Please let us know what the error is.
>
>
> -----Original Message-----
> From: usr-tc-bounces+adam=semo.net(a)mailman.xmission.com
> [mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf
> Of Shahrooz Sharghi
> Sent: Monday, March 07, 2005 10:23 AM
> To: Discussion relating to the 3Com/US Robotics Total Control
> modemsystems.
> Subject: Re: [USR-TC] e1 pri dsp software download
>
>
> thanks a lot
> i placed card in another slot but still has same problem.
> my tcm is 8.2.6
> i think it is not booting fully. how can i repair it?
>
> ----- Original Message -----
> From: "Adam Barnhill" <adam(a)semo.net>
> To: "Discussion relating to the 3Com/US Robotics Total Control
> modemsystems." <usr-tc(a)mailman.xmission.com>
> Sent: Monday, March 07, 2005 7:47 PM
> Subject: RE: [USR-TC] e1 pri dsp software download
>
>
> > If it shows with a ? Then it is not booting fully/properly. Reseat
> > the
>
> > both sides of the card and try it again. Remember front out, back
> > out,
>
> > back in, front in. Also, it may be that your TCM version is older
> > than
>
> > the TCS version of code on your DSP.
> >
> > -----Original Message-----
> > From: usr-tc-bounces+adam=semo.net(a)mailman.xmission.com
> > [mailto:usr-tc-bounces+adam=semo.net@mailman.xmission.com] On Behalf
> > Of Shahrooz Sharghi
> > Sent: Sunday, March 06, 2005 1:45 PM
> > To: usr-tc(a)mailman.xmission.com
> > Subject: [USR-TC] e1 pri dsp software download
> >
> >
> > hi, i want to software download e1 pri dsp card with tcm.(file:
> > he030513.dmf) but i recive this message:
> > "failed, devices are not read yet"
> > in the tcm instead of showing this dsp slot "?" appears. is it
> > possible my card has r2 software?
> >
> >
> > _______________________________________________
> > USR-TC mailing list
> > USR-TC(a)mailman.xmission.com
> > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
> >
> > _______________________________________________
> > USR-TC mailing list
> > USR-TC(a)mailman.xmission.com
> > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
>
>
> _______________________________________________
> USR-TC mailing list
> USR-TC(a)mailman.xmission.com
> http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
>
> _______________________________________________
> USR-TC mailing list
> USR-TC(a)mailman.xmission.com
> http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________
USR-TC mailing list
USR-TC(a)mailman.xmission.com
http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
i have a correct consol cable, it works with NMC or Netserver card.
but it doesn't work with hiperarc, card jumpers is set for 9600 and i try
9600,19200,57600,115200
but still doesn't work. what do you think about problem?
