- USR-TC - mailman.xmission.com

Who's at fault?
by Gen Camiling 28 Aug '02

28 Aug '02

OK now this is a typical TELCO-Client everything's working on our side scenario. Im installing a TC-1000 Hiper System to a client 90-port digital using E1/R2 signalling. Software codes installed is that of TCS 4.3. When you plugged-in the span line to the HiperDSP all LED utilization maxxed-out (100%) and when i go to console and check the status here's what im getting: Tslot Status Modem Blocking Call ID Span Connect Status Status 00 Fchan N/A UNBLOCKED 0x00000000 Ok 01 Dial In 001 UNBLOCKED 0x0001000E Ok 02 Dial In 002 UNBLOCKED 0x0001010E Ok 03 Dial In 003 UNBLOCKED 0x0001020E Ok . . . 16 Dchan N/A UNBLOCKED 0x00000000 Ok . . 31 Dial In 030 UNBLOCKED 0x00011D0E Ok Telco is saying that on their switching side all ports/channel are IDLE. I did a trace debug on the span to see any activity using "trc dbg 30 1" and did a reboot on their NOKIA line driver and here's what i got: ASM ch 01 : PRO_A_INC -> A_LINE_SR : 0362 Block_Out (Ch.255): 06:27:20:138 ASM ch 01 : PRO_A_INC -> A_LINE_SR : 0363 Relse_Out (Ch.255): 06:27:20:138 ASM ch 01 : A_LINE_RS -> PRO_A_INC : 0300 Seize_In (Ch.255): 06:27:20:138 ASM ch 01 : PRO_A_INC -> A_LINE_SR : 0364 Szack_Out (Ch.255): 06:27:35:138 ASM ch 01 : A_REG_CM -> A_REG_SR : 03E4 A_4_pulsed (Ch.255): 06:27:43:138 ASM ch 01 : PRO_A_INC -> A_LINE_SR : 0363 Relse_Out (Ch.255): 06:27:45:138 ASM ch 01 : PRO_A_INC -> A_LINE_SR : 0366 Clrbck_Out (Ch.255): 06:27:53:138 ASM ch 01 : PRO_A_INC -> A_LINE_SR : 0363 Relse_Out (Ch.255): 06:27:55:138 ASM ch 01 : PRO_A_INC -> A_LINE_SR : 0366 Clrbck_Out Telco is claiming that their switch is waiting for the A-1 register which the HiperDSP is not sending. But isn't it suppose to be in IDLE state first not Dial-In as indicated by the status? Here's my Question on the list: 1. Can anyone describe briefly the trace debug parameters? If i recall it right, it used to have an arrow pointing to the left or right determining if the signal is/was originating from the TELCO side or from the TC side. 2. A-1 register is send next digit, does the HiperDSP really detects or responds to this request (obviously it will but apparently am not seeing it),perhaps because of the current state of my HiperDSP that's why am not seeing the A-1 register. 3. Finally, any thoughts/suggestion on another way of trouble locating and clearing this issue? Oh, one more thing i did a loopback from the TC to the NOKIA line driver of the span it detects it, but if i do a loopback all the way to their switch TELCO says its not detecting it. Hmmm, when i did a loopback on their NOKIA line driver they still say they're not detecting it. Man, this is supposed to be a normal regular installation....can't collect to the client because of this issue...so guys....WHO'S AT FAULT???? -- Best regards, Gen ================================== Gen Camiling Chief Technical Officer International Micro Village, Inc. PHILIPPINES (63)(2) 7512130 http://www.imvi.com.ph mailto:gcamiling@imvi.com.ph ==================================

1 0

RE: [USR-TC] Radius Port
by RickL＠solunet.com 28 Aug '02

28 Aug '02

Sorry, Yes...Old code does not support it. Try upgrading the Netserver Software as high as your Memory and flash will allow. You may find you can change the port for Accounting, but not Radius for TCS3.3 and older... Weird. That's ComOS (Livingston), and it's always supported alternate port numbers on PM2's and Pm3's. Rick Team Solunet -----Original Message----- From: Lisa Casey [mailto:lisa@jellico.net] Sent: Wednesday, August 28, 2002 1:34 PM To: usr-tc(a)mailman.xmission.com Subject: Re: [USR-TC] Radius Port Hi Rick, I have the same problem. Using this command does NOT change the radius port from the default of 1645 to 1812. Isn't this dependant upon the software version on the Total Control unit, i.e., older software just will not support radius port 1812?? Thanks, Lisa Casey, Webmaster Netlink 2000, Inc. lisa(a)jellico.net ----- Original Message ----- From: <RickL(a)solunet.com> To: <usr-tc(a)mailman.xmission.com> Sent: Wednesday, August 28, 2002 1:04 PM Subject: RE: [USR-TC] Radius Port > >>set authentic xxx.xxx.xxx.xxx <port> [secret password] > > Rick Louizos > Solunet Soluserve TAC Manager > 1571 Robert J. Conlan Blvd. suite 110 > Palm Bay, Fl. 32905 > Phone Numbers: > Phone: (888)449-5766 / Fax: (321)676-1287 > Internet Addresses: > mailto:RickL@solunet.com / http://www.solunet.com > > > -----Original Message----- > From: Scott Bailey [mailto:scott@epix.net] > Sent: Wednesday, August 28, 2002 12:55 PM > To: usr-tc(a)mailman.xmission.com > Subject: [USR-TC] Radius Port > > > How do you change the default radius authentication port > from 1645 on a Netserver. I tried > > set authentic <ip> <secret> <port> > > Show global still says 1645. > > > Thanks > > > ---- > Scott Bailey > Systems Engineering > Epix Internet Services > scott(a)epix.net > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

3 2

WTB: AS5100 router card sets/ Quad modem fan out cables.
by Stephen Rivera - WRCA.Net 28 Aug '02

28 Aug '02

Hello folks. Just stopping by in search of some TC hardware: I am looking to buy.... AS51-15A-E NAC with async interface nic..upto 10 sets. This is the card set that shipped in the Cisco version of the Quad bundle. This card set was a 2511 router in disquise:) Also looking for the Quad modem fan out cables (on cable itself...PN#1.009.614-C). In plastic 3com bag they are 67-000240-00 TWH Quad RS232 NIC accessory. They are the mini-DB60 to 4 port RS232 cables. I have ben able to pick up these on this list in the past. Hopefully I can get lucky again. If you haven't notice the fall in the refurbished TC1000 hardware costs, let me tell you it has. Give me a call if you need anything. I have tons of Hiper everything. and parts and pieces. Look forward to helping you in any way I can.....steverivera(a)wrca.net

1 0

Netserver configuration HELP.
by Fred Ebnereza 28 Aug '02

28 Aug '02

I'm trying to configure my NetServer and NMC board in USR-TC. I don't have the console cable that comes with the device. I'm using a null-modem cable and the com port adapter I use for my Cisco router. when I run HyperTerminal with 9600,1,8,n,1,hardware I can't get connected to neither of the board but while cable is connected if I reboot the box (USR-TC) I see the login prompt on hyperterminal session for the NetServer or NMC but I can't type anything to login as !root I reset the board (switch#5) but still is the same . Any clue? please Fred

1 0

RE: [USR-TC] Radius Port
by RickL＠solunet.com 28 Aug '02

28 Aug '02

>>set authentic xxx.xxx.xxx.xxx <port> [secret password] Rick Louizos Solunet Soluserve TAC Manager 1571 Robert J. Conlan Blvd. suite 110 Palm Bay, Fl. 32905 Phone Numbers: Phone: (888)449-5766 / Fax: (321)676-1287 Internet Addresses: mailto:RickL@solunet.com / http://www.solunet.com -----Original Message----- From: Scott Bailey [mailto:scott@epix.net] Sent: Wednesday, August 28, 2002 12:55 PM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] Radius Port How do you change the default radius authentication port from 1645 on a Netserver. I tried set authentic <ip> <secret> <port> Show global still says 1645. Thanks ---- Scott Bailey Systems Engineering Epix Internet Services scott(a)epix.net _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

3 2

RE: [USR-TC] Radius Port
by MPuras＠solunet.com 28 Aug '02

28 Aug '02

dont forget to issue "save all" Thanks, Mario Puras SoluNet Technical Support Mailto: mpuras(a)solunet.com Direct: (321) 309-1410 888.449.5766 (USA) / 888.SOLUNET (Canada) -----Original Message----- From: RickL(a)solunet.com [mailto:RickL@solunet.com] Sent: Wednesday, August 28, 2002 1:05 PM To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] Radius Port >>set authentic xxx.xxx.xxx.xxx <port> [secret password] Rick Louizos Solunet Soluserve TAC Manager 1571 Robert J. Conlan Blvd. suite 110 Palm Bay, Fl. 32905 Phone Numbers: Phone: (888)449-5766 / Fax: (321)676-1287 Internet Addresses: mailto:RickL@solunet.com / http://www.solunet.com -----Original Message----- From: Scott Bailey [mailto:scott@epix.net] Sent: Wednesday, August 28, 2002 12:55 PM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] Radius Port How do you change the default radius authentication port from 1645 on a Netserver. I tried set authentic <ip> <secret> <port> Show global still says 1645. Thanks ---- Scott Bailey Systems Engineering Epix Internet Services scott(a)epix.net _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

Radius Port
by Scott Bailey 28 Aug '02

28 Aug '02

How do you change the default radius authentication port from 1645 on a Netserver. I tried set authentic <ip> <secret> <port> Show global still says 1645. Thanks ---- Scott Bailey Systems Engineering Epix Internet Services scott(a)epix.net

1 0

RE: [USR-TC] Netserver configuration HELP.
by RickL＠solunet.com 28 Aug '02

28 Aug '02

Fred, You need the TC1000 Console cable (PN 3C05-8812-00). Otherwise, make one: RJ-45 to DB-9 Pinout RJ-45 DB-9 3 1 6 2 5 3 2 4 4 5 3 6 7 7 8 8 Sincerely, Rick Team Solunet -----Original Message----- From: Fred Ebnereza [mailto:febnereza@daston.com] Sent: Wednesday, August 28, 2002 4:31 PM To: 'usr-tc(a)mailman.xmission.com' Subject: [USR-TC] Netserver configuration HELP. I'm trying to configure my NetServer and NMC board in USR-TC. I don't have the console cable that comes with the device. I'm using a null-modem cable and the com port adapter I use for my Cisco router. when I run HyperTerminal with 9600,1,8,n,1,hardware I can't get connected to neither of the board but while cable is connected if I reboot the box (USR-TC) I see the login prompt on hyperterminal session for the NetServer or NMC but I can't type anything to login as !root I reset the board (switch#5) but still is the same . Any clue? please Fred _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

Upgrade Dsp's
by Terry Kennedy 27 Aug '02

27 Aug '02

When upgrading the code in a dsp 3com once said that the modem should returned to default and then then up for the proper switch type and so on. I have looked through my notes on this and can't find what I am looking for -- under the card level settings, under the software there are a bunch of choices: Restore E1/T1 and modems from default Save E1/T1 and modems to NVRam Restore template 1 config from default Save template 1 config to NVRam Restore template 1 config from NVRam Refresh template 1 from NvRam Refresh template 1 config channels And so on.... While trying to figure out the sequence you are supposed to perform here, I realized I don't have much of an understanding of what these REALLY do. Although I can guess on some of this, what's the difference between retoring the modems to default and restoring the templates from default? Is there a differnce between retoring the NVRAM from default and restoring the template 1 config to default, then loading template 1, then saving to the NVRAM???? Quite confusing. Any info here would be greatly appreciated!! I'll take anything from "here's the link, go read about it" to "don't know what all those really either, but here's the method for setting up the DSP's" to acomplet expanation of templates, default settings and general architecture of the dsp!! Thanks ahead of time. Terry Kennedy OlyPen,

2 2

analog/busy tone/working ok after checking dialtone
by pankaj 27 Aug '02

27 Aug '02

Hi folks, I have nasty senerio, I have many analog lines. 3com(tc1000) Now some of them are behaving nasty. Once or twise user able to login properly in that line. Now in some lines I am geeting busy tone, evenif line is free(i.e no user loged in). Now I unplug that line from modem , and leave it in air, but still I got busy tone on that number, Than I pluged it in to phone-intrument(handset) and than also I got busy tone on that number. now i pickeup the receiver and check the dialtone.Dialtone was ok, after checking dial tone I was able to get ring on that number, and user is also able to login. The same trouble I faced in many lines in three-fine quards-modems. My telco people come and check earthing and all but seems everything ok. Any clue will help me out ?? Thanks pankaj

1 0