- USR-TC - mailman.xmission.com

got no ip address
by Sherwin Torres 03 Oct '04

03 Oct '04

1 0

Bus Management Failure
by Sherwin T 29 Sep '04

29 Sep '04

Hi! I would like to re-post the Bus Management Failure I encounter because my previous mail host is problematic. Here are the information of the Total Control: DSP - 3.5.12 NMC - 8.6.3 ARC - V5.3.2/Non-Encr Any comments or suggestion is highly appreciated on how to prevent or solve this problem. Thanks, Sherwin

1 0

RE: [USR-TC] resetting of DSP card due to bus failure
by Joel - Fox Computers 27 Sep '04

27 Sep '04

3.5.12 of the DSP software is the devil - get 3.5.109, not sure if it solves your specific problem but it is more reliable. -----Original Message----- From: Sherwin Torres [mailto:sherwint@walla.com] Sent: Monday, September 27, 2004 8:45 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] resetting of DSP card due to bus failure Hi Alex, Here are the version info of my TC which encounters auto resetting of DSP cards and found bus management failure. DSP : V5.3.110/Non-Encr NMC : 8.6.3 DSP : 3.5.12 Thanks, Sherwin _____ Walla! Mail - get your free 1G mail <http://www.walla.com> today

1 0

resetting of DSP card due to bus failure
by Sherwin Torres 27 Sep '04

27 Sep '04

1 0

TC1000 / DOV
by Patric Cole 23 Sep '04

23 Sep '04

Hi, I'm currently trying to work out why my TC1000 is not accepting DOV calls. Digital ISDN calls come in fine, but with DOV the call gets routed to a modem on the ARC and does not answer properly. No call blocking is enabled on the HiperDSP. I also have a TC100 and it is accepting DOV calls fine (using S68.1=1 and S68.2=1), but these registers do not do anything on the DSP modems. Can anyone shed some light as to why it might not be working? Running firmware version 2.1.9 on the DSP. Thanks, Patrick

1 0

Need to move some Hiper DSP's
by Stephen Rivera - WRCA.Net 22 Sep '04

22 Sep '04

Have about 50 Hiper DSP cards sets available. Need to make some space for arriving stock 69-002092-00 Hiper DSP T1/PRI card sets $50ea ....buy a couple :) Qty purchase discount available. Reply off-list to steverivera(a)wrca.net Steve Rivera WR Consultant Associates, Inc. Dir: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

1 0

NI-2/5ESS with V.92
by Paul Williams - Speedline Tech 22 Sep '04

22 Sep '04

(my previous post got messed up) My understanding is that there are 2 popular PRI service types: NI-1 and NI-2 There are then different forms of implementation of each, for example 5ESS (AKA: custom NI-2) is an implementation form of NI-2. I have four DSP’s each connected to a Telus PRI NI-2 service. Each PRI has 1 D channel and 23 B channels. Notice that the primary switch type in my trunk settings is set to 5ESS. Telus have suggested that I change it to NI-2 and see if that resolves my problem. DSP Software revision = 3.5.109 Framing Mode dsx1ESF Line Coding Options dsx1B8ZS Circuit Identifier Loopback Configuration dsx1NoLoop Signal Mode messageOriented Transmit Clock Source loopTiming NIC Type longHaul Response to Remote Loopback ignore Jitter Attenuation attenJitterOnRcvr Transmit Line Build Out dB0pt0 Dial In Address dnis Dial In/Out Trunk Start Signal Type wink Ack Wink On Dial In Address Info Received disabled Dial Out Address Delay 70 Dial In/Out Trunk Type eAndMTypeII Primary Switch Type priSw5ESS Idle Byte Pattern 254 Receiver Gain dB26 Tone Type dtmf Number of DTMF Tones 4 Send Code dsx1SendNoCode External Signaling Mode (will take effect next boot) none Overlap Receiving Mode disable Overlap Receiving Inbound Digits Expected 12 Overlap Receiving Timeout Delay 12 ARC: Software Revision = 5.3.3 Is there any ARC configuration needed to get V.92 working? When I select the whole card in TCM and go to the interface/V.92 options, V.92 appears to be disabled; however, if I select the lower LED and go to the same options, the V.92 functionality appears to be enabled. Setting V.92 aside, if a dial-up user is connected and has call waiting enabled and internet notification software running (for example: USR’s ICN) when a call comes through – the user doesn’t get notification when connected to our system. If the user disconnects and reconnects to a different ISP (for example a freebie NetZero account) the notification works! I’m not sure what the problem is, whether it’s my total control config or PRI config. Any suggestions would be greatly appreciated. I’ll be switching the primary switch type to NI-2 tomorrow night – I’ll post the results. Thanks, Paul. -- Outgoing mail is certified Virus Free. Checked by AVG Anti-Virus (http://www.grisoft.com) Version: 7.0.271 / Virus Database: 264.9.3 - Release Date: 9/17/2004 -- Outgoing mail is certified Virus Free. Checked by AVG Anti-Virus (http://www.grisoft.com) Version: 7.0.271 / Virus Database: 264.9.4 - Release Date: 9/21/2004

1 0

T1-PRI Question
by Paul Williams - Speedline Tech 21 Sep '04

21 Sep '04

1 0

NI-2/5ESS with V.92
by Paul Williams - Speedline Tech 21 Sep '04

21 Sep '04

1 0

NI-2/5ESS with V.92
by Paul Williams - Speedline Tech 21 Sep '04

21 Sep '04

I have a V.92 enabled 3com total control hub with 4 active DSP cards. Our WAN service provider is Telus who provide us with a NI-2 service and switch type 5ESS. Here’s the problem: When dialup users are online and have internet call notification software running, they don’t get notified that an incoming call is coming through. This wasn’t a problem with our previous service provider (Bell) who offered us a NI-1/DMS-100 service. Thank you, Paul. -- Outgoing mail is certified Virus Free. Checked by AVG Anti-Virus (http://www.grisoft.com) Version: 7.0.271 / Virus Database: 264.9.3 - Release Date: 9/17/2004

2 1