- USR-TC - mailman.xmission.com

(usr-tc) FlexPath configuration
by Richard Roy 17 Mar '00

17 Mar '00

Hi, I would like to know the value for those HiperDSP parameters use with a CH-T1 FlexPath. My config shows: Dial in Address: Noaddress Ack Wink on dial in address info: Enabled (for the first and the last flexpath in the trunk) Every others DSP are set to disabled. Note: What happens otherwise (first flexpath ack wink = disabled) is that once that trunk fill up, none of the rest will accept calls - the customer hears the dialing, then dead air. Thank you. Richard Roy, CCNA Technical Associate Network Intelligence Design Richard.Roy(a)aliant.ca Phone: (506) 694-6983 Fax: (506) 694-2525 www.nbtel.nb.ca www.aliant.ca - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) TC Rack Power Consumption
by USRobotics TC Mailing List 16 Mar '00

16 Mar '00

Great, helped me out a lot. -----Original Message----- From: Andy [mailto:andy@mega-mail.far.net] Sent: Wednesday, March 15, 2000 2:47 PM To: USRobotics TC Mailing List Subject: Re: (usr-tc) TC Rack Power Consumption We have some of our older dialup hardware (TC w 1 70amp PS + 12 quads) running on Smart UPS 900's... They work quite well and will run the units for ~20 mins. The newer stuff (TC w/2 70amp PS + 9 pri DSP's) we run off our matrix xr, and I find they draw about 1kv. So you'd want to go with atleast a 1400 ups. Don't know if this will actually be any help... :) If anything make sure you over-buy on the ups. A few years ago we were having major problems with some netserver cards that we found went away when we got our first matrix system online. Andy > >I am trying to find out what the power requirements are for a couple of >different rack configurations, in order to figure out what size UPS I >require for each rack. >I've researched the 3com newsgroup, as well as the list serv and the support >site, but haven't been able to find any usable information. >One Hiper rack running Dual 70 Amp PS & 7 HiPer DSP's >One Hiper rack running Dual 70 Amp PS & 1 HiPer DSP >Two Racks running Dual 45 Amp PS & 12 Quad's >Any feedback appreciated. > > >- > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > > ----- Andy <andy(a)mega-mail.far.net> Far Networks http://www.far.net/ - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

(usr-tc) Defective modem etc.
by bert.f＠staff.pacific.net.ph 16 Mar '00

16 Mar '00

Hi! I believed there a command to show which modem is defective in a HiperDSP card, but right now i can't seem to find it, any one has knoe this command? Thanks, Bert Herbert Frias Network-RAS Group Pacific Internet, Philippines Tel.(632) 637-1700 DL. (632) 683-7164 Fax. (632) 683-7197/98 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

4 4

Re: (usr-tc) Defective modem etc.
by Campbell Simpson 15 Mar '00

15 Mar '00

Hi Mitch I'd be interested in the perl script also. Cheers Campbell >>> mitch(a)keyconn.net 03/16/00 06:01 >>> At 07:49 PM 3/15/00 +0800, bert.f(a)staff.pacific.net.ph wrote: >Hi! > >I believed there a command to show which modem is defective in a HiperDSP >card, but right now i can't seem to find it, any one has knoe this command? I'm not aware of a command, but there is a perl script that will poll the chassis for modem failure rates and write the results to a web page. I can't remember where I got it, called badmodems.pl. Let me know if you can't find it, I can get a copy to you later this afternoon. -- Kirk Mitchell-General Manager mitch(a)keyconn.net Keystone Connect Unlock Your World Altoona, PA 814-941-5000/886-2500 http://www.keyconn.net - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) TC Rack Power Consumption
by USRobotics TC Mailing List 15 Mar '00

15 Mar '00

I am trying to find out what the power requirements are for a couple of different rack configurations, in order to figure out what size UPS I require for each rack. I've researched the 3com newsgroup, as well as the list serv and the support site, but haven't been able to find any usable information. One Hiper rack running Dual 70 Amp PS & 7 HiPer DSP's One Hiper rack running Dual 70 Amp PS & 1 HiPer DSP Two Racks running Dual 45 Amp PS & 12 Quad's Any feedback appreciated. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) Weird characters appearing as User-Name in HiperARC
by Colin Wantling 14 Mar '00

14 Mar '00

Hi, I don't know the cause, but setting PPP to OFFLOAD in the HiperArc reduces if not eliminates the problem. regards, Colin Wantling Energis NV, Netherlands > ---------- > From: Louis_Sim@3com.com[SMTP:Louis_Sim@3com.com] > Reply To: usr-tc(a)lists.xmission.com > Sent: Tuesday, 14 March 2000 5:52 > To: usr-tc(a)lists.xmission.com > Subject: (usr-tc) Weird characters appearing as User-Name in HiperARC > > > > Hi there, > > I have a customer in Sinagpore using HARC 4.1.59-6 for dial-in user (newly > installed). > > The problem they are having is that when monitoring the account records > using > monitor radius. It shows many unknown userid. Sample below. > User-Name : > Â»Â®ÃÃ¦qÂ¢_'Ã³Ã_iÃ®Ã®_Â·Ã£Â»yÃ½_Ã©Ã¸&_Â¥'EÂ¥Ykg_Â·ÃÂ¤Ã_Ã¨ÃÃ·Â¡m$Â¡58|_Â·_D_Ec_k__gÂ¿Â·oA_Â© > User-Name : > Â»Â®ÃÃ¦qÂ¢_'Ã³Ã_iÃ®Ã®_Â·Ã£Â»yÃ½_Ã©Ã¸&_Â¥'EÂ¥Ykg_Â·ÃÂ¤Ã_Ã¨ÃÃ·Â¡m$Â¡58|_Â·_D_Ec_k__gÂ¿Â·oA_Â© > User-Name : S7895476u' > User-Name : Ã'#ÃÂ°1_y_Ã·ÃÃ Â¿>oÃªÂ°Ã¨z_&_, > Â²Ã½_ÃÃ®Ã¾@|#Ã__Ã¦ZÃÃ_ÃÃÂ²ÃÃ¶ÃÃ*_Â´GVXÃRÃ°EUR,_34Ã___A-rÂ§- > > Customer is using Radius for Authentication. > > Any ideas as to why this is happening. > > Thanks in advance for any contributions. > > Regards. > Louis Sim > > > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) NMC gone silent
by Jeremy Shaffner 14 Mar '00

14 Mar '00

About a week ago, one of our NMC stopped responding, both to SNMP and to ICMP pings. Yet the HARC indicates that the NMC has at least gotten the SNMP requests: HiPer>> show nmc status NMC STATUS Last NMC Query was received at: 14-MAR-2000 12:12:11 Is there anyway to get it running again without having to drive out to powercycle or reseat it? Thanks, --- Jeremy Shaffner System Administrator JORSM Internet jer(a)jorsm.com http://www.jorsm.com/~jer/pgp.key - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

RE: (usr-tc) Weird characters appearing as User-Name in HiperARC
by Stainforth, Matthew 14 Mar '00

14 Mar '00

verify that your RADIUS secrets are set correctly on both ends Matthew Stainforth || Technical Services Manager || BrunNet Inc. > -----Original Message----- > From: Louis_Sim(a)3com.com [mailto:Louis_Sim@3com.com] > Sent: Tuesday, March 14, 2000 12:52 PM > To: usr-tc(a)lists.xmission.com > Subject: (usr-tc) Weird characters appearing as User-Name in HiperARC > > > > > Hi there, > > I have a customer in Sinagpore using HARC 4.1.59-6 for > dial-in user (newly > installed). > > The problem they are having is that when monitoring the > account records using > monitor radius. It shows many unknown userid. Sample below. > User-Name : > Â»Â®ÃÃ¦qÂ¢_'Ã³Ã_iÃ®Ã®_Â·Ã£Â»yÃ½_Ã©Ã¸&_Â¥'EÂ¥Ykg_Â·ÃÂ¤Ã_Ã¨ÃÃ·Â¡m$Â¡58|_Â·_D_Ec_k__gÂ¿Â·oA_Â© > User-Name : > Â»Â®ÃÃ¦qÂ¢_'Ã³Ã_iÃ®Ã®_Â·Ã£Â»yÃ½_Ã©Ã¸&_Â¥'EÂ¥Ykg_Â·ÃÂ¤Ã_Ã¨ÃÃ·Â¡m$Â¡58|_Â·_D_Ec_k__gÂ¿Â·oA_Â© > User-Name : S7895476u' > User-Name : Ã'#ÃÂ°1_y_Ã·ÃÃ Â¿>oÃªÂ°Ã¨z_&_, > Â²Ã½_ÃÃ®Ã¾@|#Ã__Ã¦ZÃÃ_ÃÃÂ²ÃÃ¶ÃÃ*_Â´GVXÃRÃ°?,_34Ã___A-rÂ§- > > Customer is using Radius for Authentication. > > Any ideas as to why this is happening. > > Thanks in advance for any contributions. > > Regards. > Louis Sim > > > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Weird characters appearing as User-Name in HiperARC
by Louis_Sim＠3com.com 14 Mar '00

14 Mar '00

Hi there, I have a customer in Sinagpore using HARC 4.1.59-6 for dial-in user (newly installed). The problem they are having is that when monitoring the account records using monitor radius. It shows many unknown userid. Sample below. User-Name : »®Ïæq¢_'óÐ_iîî_·ã»yý_éø&_¥'E¥Ykg_·Ì¤Æ_èË÷¡m$¡58|_·_D_Ec_k__g¿·oA_© User-Name : »®Ïæq¢_'óÐ_iîî_·ã»yý_éø&_¥'E¥Ykg_·Ì¤Æ_èË÷¡m$¡58|_·_D_Ec_k__g¿·oA_© User-Name : S7895476u' User-Name : Ô'#Ô°1_y_÷íà¿>oê°èz_&_, ²ý_Ýîþ@|#Ù__æZÃÙ_ÁÃ²ÃöËÊ*_´GVXÌRð,_34Þ___A-r§- Customer is using Radius for Authentication. Any ideas as to why this is happening. Thanks in advance for any contributions. Regards. Louis Sim - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) USR Netserver 8 console cable (RJ45 to DB9 male)
by bfox＠fox-net.net 13 Mar '00

13 Mar '00

Hi: We have a couple of these boxes, and need to make a console cable like captioned. Anyone have the pinout for this? Real pain in the butt to use adapters, etc. to get the original console cable to work. Thanks! Ben - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1