- USR-TC - mailman.xmission.com

(usr-tc) Radius attributes for Total Control
by Steve Cobb 28 Feb '01

28 Feb '01

Hello all, I was wondering if anyone might know some radius attributes for the TCR or where I can find a list. I'm using a HiperArc with HiperDSP modems. I need to be able to control concurrency and the number of B channels that an ISDN user can bind. We are using RadiusNT and would like to put these entries in a text file or the ODBC database. Thanks all, Steve Cobb - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) dead HiPer ARC
by Kirk Mitchell 28 Feb '01

28 Feb '01

My HiPer ARC failed a short time ago, no warning or anything, about 5 minutes after resetting a DSP through TCM. Run/Fail light just turned red and it quit working completely, dropped most callers and new calls started getting busies. Hardware reset through TCM had no effect whatsoever, yet physically pulling the card and reseating it had the card reset and working in a few minutes. How can I go about determining what caused this? Is this one on it's last leg? What effect might resetting the DSP have had? Thanks, -- Kirk Mitchell-General Manager mitch(a)keyconn.net Keystone Connect Unlock Your World Altoona, PA 814-941-5000 http://www.keyconn.net - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) FS: USR Total Control Chassis
by signal＠shreve.net 27 Feb '01

27 Feb '01

USR Total Control Chassis with Integrated fan tray 70A power supply 12 Quad digital modems (48 modems total) Dual PRI NIC and NAC Netserver NIC and NAC NMC NIC and NAC $1300!!!!!! ----------------------------------------------- I'm buying / selling used CISCO gear!! email me for a quote Brian Feeny,CCDP,CCNP+VAS Scarlett Parria signal(a)netjam.net scarlett(a)netjam.net 318-222-2638 x 109 318-222-2638 x 101 Netjam, LLC http://www.netjam.net 1401 Oden St. Suite 18 Shreveport, LA 71104 Fax 318-221-6612 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) Routing a subnet
by Brian Becker 27 Feb '01

27 Feb '01

Can you do ospf instead of rip? Brian Becker President, Poplar Bluff Internet, Inc. (www.semo.net) Home of TotallyFabricated.com Software: Total Scrutinizer (www.TotalScrutinizer.com) - Tech Support Just Got Easier! WebGabber (www.WebGabber.com) - html-based Chat Software -----Original Message----- From: owner-usr-tc(a)lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of Steve Monkhouse Sent: Tuesday, February 27, 2001 12:34 AM To: usr-tc(a)lists.xmission.com Subject: RE: (usr-tc) Routing a subnet In the S&A Server / Routing tab for the User you are setting up.. You need to enter the framed route to route a subnet to them.. using your example the route in S&A would be.. 99.99.99.32/27 155.155.155.201 1 no you dont need to do an ip route on your cisco if you use RIPv2 once the connection is established the route should propogate to the cisco automatically. Steve -----Original Message----- From: owner-usr-tc(a)lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of Kirk Mitchell Sent: Tuesday, February 27, 2001 3:23 PM To: usr-tc(a)lists.xmission.com Subject: RE: (usr-tc) Routing a subnet At 10:24 AM 2/27/01 +1000, Steve Monkhouse wrote: >http://www.dcr.net/~mandrews/usrtoys/subnet-route.txt Framed-IP-Address = 192.192.192.xxx, # customer's static IP address above Framed-Netmask = 255.255.255.255, Framed-Route = "193.193.193.0/24 192.192.192.xxx 1", # network to be routed, netmask, static IP of customer, metric I'm using 3Com S&A Server. In the routing entry, it asks for "Framed Route" in the form of "destination gateway metric", with no field requesting a netmask. Would the netmask be part of the destination entry? Thus, where 155.155.155.201 is the static assigned IP and 99.99.99.32/27 is the assigned subnet; Framed-IP-Address = 155.155.155.201 Framed-Route = 99.99.99.32 255.255.255.224 155.155.155.201 1 Would this be correct? Also, will this handle all the routing, or do I also need something like ip route 99.99.99.32 255.255.255.224 155.155.155.201 in my Cisco gateway router as well? Thanks, -- Kirk Mitchell-General Manager mitch(a)keyconn.net Keystone Connect Unlock Your World Altoona, PA 814-941-5000 http://www.keyconn.net - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) Routing a subnet
by Kirk Mitchell 27 Feb '01

27 Feb '01

At 10:24 AM 2/27/01 +1000, Steve Monkhouse wrote: >http://www.dcr.net/~mandrews/usrtoys/subnet-route.txt Framed-IP-Address = 192.192.192.xxx, # customer's static IP address above Framed-Netmask = 255.255.255.255, Framed-Route = "193.193.193.0/24 192.192.192.xxx 1", # network to be routed, netmask, static IP of customer, metric I'm using 3Com S&A Server. In the routing entry, it asks for "Framed Route" in the form of "destination gateway metric", with no field requesting a netmask. Would the netmask be part of the destination entry? Thus, where 155.155.155.201 is the static assigned IP and 99.99.99.32/27 is the assigned subnet; Framed-IP-Address = 155.155.155.201 Framed-Route = 99.99.99.32 255.255.255.224 155.155.155.201 1 Would this be correct? Also, will this handle all the routing, or do I also need something like ip route 99.99.99.32 255.255.255.224 155.155.155.201 in my Cisco gateway router as well? Thanks, -- Kirk Mitchell-General Manager mitch(a)keyconn.net Keystone Connect Unlock Your World Altoona, PA 814-941-5000 http://www.keyconn.net - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

(usr-tc) Memory Upgrade for HiperARCs?
by Tim Huffman 26 Feb '01

26 Feb '01

We have a HiperARC with 64MB of RAM, and it's starting to show its limitations. We were looking at possibly upgrading to 128MB, but $950 (quote from USR) seems like a whole lot of money. What are the odds that these things use standard SDRAM? If not, does anyone know of lower cost alternatives? -- -Tim ___________________________________________________ Tim Huffman -------- JORSM Internet, Internet Services Assistant Manager ---- 7 Area Codes in Chicagoland timh(a)jorsm.net ------ 100 Mbps+ Connectivity, 56K-DS3 (219)322-2180 ------- Quality Service, Affordable Prices http://www.jorsm.net --- Serving Gov, Biz, Indivds Since 1995 _____________________________________________________ - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

5 5

RE: (usr-tc) TC NetServer v34 analog
by list＠angelnet.com.br 26 Feb '01

26 Feb '01

Heii Helloo.. Ho yea.. the TC is working fine i have the manual ( idowloaded from 3com sitee ), but in manual only speak how set fixed ips to use with the internal user tables ( well, if i read all manuals ok and undestand . heeh).. Now my TC is working in a pool ip modes.. without problems ( well only the standart problems of this TC )... Hamm, sorry iam using the Radius .. and yeahh i have one teminal cable .. Pleasee can you help me? -----Original Message----- From: albert [mailto:emmanuel@mwt.net] Sent: Monday, February 26, 2001 1:36 AM To: list(a)angelnet.com.br Subject: RE: (usr-tc) TC NetServer v34 analog Hello,... first may i ask if you have a set of manuals for the unit? and a USR consol cable? albert > -----Original Message----- > From: owner-usr-tc(a)lists.xmission.com > [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of > list(a)angelnet.com.br > Sent: Monday, February 26, 2001 10:15 AM > To: usr-tc(a)xmission.com > Subject: (usr-tc) TC NetServer v34 analog > > > Hello Peoples?? > Well sorry if my question is out of this list, but i need some help, and > 3com dont help me.. NEVER ... > Well i need ( if possible ) configure my Total Control Netserver > V.34 Analog > to use with fixed IP's ...... > Pleaseeee someone help mee... is urgentt...... > My ICQ 14484847 WEGA > > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 3

(usr-tc) v90 on the nmc
by Brian 26 Feb '01

26 Feb '01

If you have an NMC with v90 enabled, and you pull the flash out and move it to another NMC that is not v90 enabled, will that new nmc now be v90 enabled? In other words, is the key set in the flash and transportable between nmc's? or is it dependent on other factors? Brian ----------------------------------------------- I'm buying used CISCO gear!! email me for a quote Brian Feeny e:signal@shreve.net CCNP+Voice/ATM/Security p:318.222.2638x109 CCDP f:318.221.6612 Network Administrator ShreveNet Inc. (ASN 11881) - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

7 12

(usr-tc) TC NetServer v34 analog
by list＠angelnet.com.br 26 Feb '01

26 Feb '01

Hello Peoples?? Well sorry if my question is out of this list, but i need some help, and 3com dont help me.. NEVER ... Well i need ( if possible ) configure my Total Control Netserver V.34 Analog to use with fixed IP's ...... Pleaseeee someone help mee... is urgentt...... My ICQ 14484847 WEGA - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

3 2

(usr-tc) configuring a second HiPer ARC
by Antonio Querubin 24 Feb '01

24 Feb '01

I'm installing a second HiPer ARC into a Total Control chassis and am having some difficulty integrating it into the system for automatic failover. I'm running into several issues. One problem I've run into is the IP address pools that the HARCs use. Is there a way for both HiPer ARCs to share the same IP address pool without stepping on each other? Or if one fails, can the other one automatically acquire the address pool of the failed HARC? Is there a way for the second HARC to be assigned the first HARC's IP address as a hot standby IP address? If neither HARC is configured as the owner of a modem card, how does the NMC determine (or is configured to specify) which HARC does route for a particular modem card? - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

6 5