- USR-TC - mailman.xmission.com

can't connect to cosole for usr-tc 1000
by Ahsan Shariful 24 Feb '03

24 Feb '03

Hi, I need to setup a usr-tc. Hyperterminal can't connect to usr-tc 1000. I'm using a custom cable RJ45 - DB9 ( i got the pinout from this mailing list). I tried with all bits/second (110 to 115200) and other setting as "8-None-1-Hardware". I can't figure out the problem. I don't have the null moded cables or any other cable provied with this hardware. Somebody please help :-) Ahsan --------------------------------- Do you Yahoo!? Yahoo! Tax Center - forms, calculators, tips, and more

1 0

RE: [USR-TC] Question about filters
by Joel - Fox Computers 22 Feb '03

22 Feb '03

Alex - THANKS! joel -----Original Message----- From: alex [mailto:alex@wanex.ge] Sent: Saturday, February 22, 2003 3:59 PM To: usr-tc(a)mailman.xmission.com Subject: Re: [USR-TC] Question about filters What you have to do is very simple (on HiperARC) : First of all you have to set up a tftp server (it's easy if you run linux). Then create filter files. For instance user.in and user.out. First is to allow/deny user's input and second - output. Then login to arc and do tftp. Write there (in tftp on arc) get tftp-servers-ip:filename. Example: if your tftp server is 10.0.0.1 and files are user.in and user.out do: Hiper>>tftp tftp>get 10.0.0.1:user.in ... tftp>get 10.0.0.1:user.out tftp>quit ... Then: add filter user.in add filter user.out set modem_group all filter_access on One way is simple: set user input_filter user.in set user output_filter user.out You have to have local authentication enabled for this. Another way is : On your radius server configure user to have an filter named: user (if your radius can do that. Filter_ID=input-filter-name/output-filter-name. Its explained in Hiper ARC's product reference.). Filter file have to be in ascii (text). An example of filter file is this: user.in #filter IP: 001 AND src-addr = 0.0.0.0/0; 002 ACCEPT dst-addr = 10.1.0.0/16; 003 AND src-addr = 0.0.0.0/0; 004 AND dst-addr = 10.2.1.1/32; 005 ACCEPT udp-dst-port = 53; 006 DENY; line 1 and 2 permit user to acces your local network (if local network is 10.1.0.0 255.255.0.0). line 3,4 and 5 permit user to access your dns server (if dns server's ip is 10.2.1.1). line 6 denys anything else. output filter is nearly the same but source addresses are 10.1.0.0/16 and 10.2.1.1. destination - 0.0.0.0/0 After you put filter files on arc you have to verify them by: verify filter user.in verify filter user.out. That's all I think :) Joel - Fox Computers wrote: >Hopefully someone can help. > >I've seen mention of filters on the list a couple times, but never anything I could completely follow. > >Need to figure out how to create a filter, and I know NOTHING about how to go about doing that. > >I want to create a filter to allow a particular to user to access only a single, specific IP address. > >I need to know not only what has to be in the filter, but how to go about putting it on the ARC and enabling it and such. > >Thanks in advance if you can help. > >Thanks, > >Joel > > > > > >_______________________________________________ >USR-TC mailing list >USR-TC(a)mailman.xmission.com >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

Question about filters
by Joel - Fox Computers 22 Feb '03

22 Feb '03

Hopefully someone can help. I've seen mention of filters on the list a couple times, but never anything I could completely follow. Need to figure out how to create a filter, and I know NOTHING about how to go about doing that. I want to create a filter to allow a particular to user to access only a single, specific IP address. I need to know not only what has to be in the filter, but how to go about putting it on the ARC and enabling it and such. Thanks in advance if you can help. Thanks, Joel

2 1

Three PRI Questions
by Joel - Fox Computers 21 Feb '03

21 Feb '03

Got a chassis with 10 PRI's into it. Just looking for any opinions or information on the following issues: #1. Telco says the switch is a 5ESS. If we configure the DSP's for 5ESS we intermittently lose the D-channels. Telco says that even though it's a 5ESS switch, the PRI's are configured "standard" or "national" and that we should set the Total Control for NI2. Is this normal/correct? Set it up for NI2 and D-channels appear stable and it answers calls. #2. Telco says that even though each PRI has it's own D-channel, that each PRI is configured as it's own single-PRI NFAS group with Interface ID 0. It seems to answer calls whether I just configure for FAS or if I config for NFAS assigning a different NFAS Group to each DSP. Does this matter at all? Seemed kinda wierd, but I haven't worked with PRI's that much. #3. All 10 PRI's are in a single "hunt group" with 4 different numbers assigned to that group. Regardless of the phone number I call, the call comes into the first DSP. If I busy-out that first DSP, dialing any number results in a busy-signal. In other words, if one DSP is not there, calls don't roll over to the next available PRI. I'm pretty sure this is a telco config issue - but is there something I may be doing wrong? Just want to make sure. Thanks for any help. Joel

3 2

RE: [USR-TC] Three PRI Questions
by Joel - Fox Computers 21 Feb '03

21 Feb '03

I tried two different things with no luck: 1. TCM - selected the lights at the top of the card, Configure->Actions/Commands->Timeslot,SelectAll->Software->Soft Busy Out 2. TCM - selected the whole card, Configure->Actions/Commands->Hardware->Remove From Service I'm assuming #1 took the B-channels out of service, or is there something else I should have done? -----Original Message----- From: Jeff McAdams [mailto:jeffm@iglou.com] Sent: Friday, February 21, 2003 8:02 AM To: usr-tc(a)mailman.xmission.com Subject: Re: [USR-TC] Three PRI Questions >#3. All 10 PRI's are in a single "hunt group" with 4 different numbers >assigned to that group. Regardless of the phone number I call, the >call comes into the first DSP. If I busy-out that first DSP, dialing >any number results in a busy-signal. In other words, if one DSP is not >there, calls don't roll over to the next available PRI. I'm pretty >sure this is a telco config issue - but is there something I may be >doing wrong? Just want to make sure. How are you busying them out? If you just busy the modems out and not take the B channels out of service, this is normal. Take the B channels out of service and your calls should roll over correctly. -- Jeff McAdams Email: jeffm(a)iglou.com Head Network Administrator Voice: (502) 966-3848 IgLou Internet Services (800) 436-4456

1 0

netserver crashes
by Murat Küçük 21 Feb '03

21 Feb '03

Hi, I have a netserver with 56 modems. It crashes once or more in a day. I just reboot it at certain times. But it fails after reboot. What can i do? I need help. Regards murat My netserver's info; U.S. Robotics Total Control (tm) NETServer Card V.34 V3.3.3 Build date: Nov 27 1996 Build time: 17:06:59 Network Interface Card: Ethernet (24) Packet Bus Circuit : Standard Licensed for 60 ports.

2 2

analog netserver 8/16 with V90/X2 ?
by alex 21 Feb '03

21 Feb '03

Is it possible to update/upgrade netserver 8/16 or mp 8/16 (analog) modems to be able to provide V.90/x2 ? Here http://support.3com.com/software/smofficesw.htm is some software for mp/netserver but I'm afraid that this soft is for ISDN customers. Is it possible to do 56k on analog lines?

1 0

OT: Looking for MultiSpan DSPs
by Joel - Fox Computers 19 Feb '03

19 Feb '03

Anybody have any Multispan DSP's for sale? Contact me off list please. Thanks, Joel

1 0

RE: [USR-TC] MAndrews perl utilities for USR-TC
by BSmith＠solunet.com 19 Feb '03

19 Feb '03

-----Original Message----- From: VCI Help Desk Subject: Re: [USR-TC] MAndrews perl utilities for USR-TC Does anyone configure their TC using a backup and restore method? How about by copying the config files off a TC to another TC? I noticed several config files available by doing a "list files" command. Bill ----- Original Message ----- Bill, What you want there is a Bulk File Transfer. Long story short, it takes all your configs from NVRAM, puts them into a binary file, compresses them to 1 file, and allows to take them from your HiperARC to your PC (via TFTP). Bad thing about that, you NEED to put it back to a HiperARC with the SAME version of software. You are also unable to view the contents. What I believe Scott is looking for is an application that goes to your box, gets all of the relevant data, turns it into a script such that you can then paste it. Like on a Cisco you can do a "show run" and that is your config, he is looking for a way to do that. I believe, I could be wrong though. Thanks, Brian

2 1

MAndrews perl utilities for USR-TC
by Todd Williams 19 Feb '03

19 Feb '03

Hi all, I was wondering if someone had the following Perl scripts sitting around somewhere: usrcommand.pl checkusrcfg.pl nmc-red-light.pl They seem to have disappeared from Mike Andrews' site at http://www.dcr.net/~mandrews/usrtoys/mystuff.shtml Thanks in advance, Todd

4 3