April 2003 - USR-TC - mailman.xmission.com

v90 enable string
by Marcelo Tadeu Mirabelli Marchesoni 08 Apr '03

08 Apr '03

Hi guys! First of all, excuse me about my fuzzy english. I've just purchased a used T1000 chassis, with several quad modems, a dual-pri, a netserver card and a nmc card. The chassis is fine, is working well, only does not accept conections over 33k6. The v90 enable string is missing. I've already tried to contact the local dealer, but they tell me that my chassis is too old and they aren't able to sell me one. Funny, isn't it? I purchased the chassis from them one week ago! Have anyone a solution for my case? Where I can obtain the v90 enabling string? Thanks in advance. -- [.........]s Marcelo Marchesoni rede1(a)linkway.com Sao Carlos - SP - Brasil -- Essa mensagem foi verificada contra vírus e conteúdo malicioso.

2 1

What is a 003446-0
by Paul Farber 08 Apr '03

08 Apr '03

I have to send back some leased 3COM gear, a double play upgrade from 1999. Its was 2 DSPs, a PS, and an NMC upgrade. Problem is it can't remember what was upgraded in the NMC.. the FLASH or RAM. ANyone remember which it is? My best guess is that is was a 16MB Flash upgrade up from the standard 8MB flash that came with the NMC cards. -- Paul Farber Farber Technology farber(a)admin.f-tech.net Ph 570-628-5303 Fax 570-628-5545

1 0

RE: [USR-TC] PSU question
by Joel - Fox Computers 07 Apr '03

07 Apr '03

One thing you have to make sure is that your power supplies are the same type. A person can have two 130A AC power supplies, but if you have one Type 8 power supply and one Type 4 power supply (something I've tried) you will see the exact behavior you describe - power one off and the entire rack goes down momentarily and everything restarts. My experience has been that as long as your two power supplies are exactly identical, the failover works perfectly. I've had several occasions (last night, in fact, while switching out the UPS) where I have to power one or the other off, never disconnect a user while doing it. - Joel -----Original Message----- From: Joshua Coombs [mailto:jcoombs@gwi.net] Sent: Monday, April 07, 2003 9:38 AM To: Discussion relating to the 3Com/US Robotics Total Control modem systems.; alex(a)wanex.ge Subject: Re: [USR-TC] PSU question As long as both UPSs are running within normal tolerances, fail over should work as expected. Note I have observed powersupply fail over tripping over itself in the past using 130A 120v powersupplies on dual feeds. Both power supplies were green, power down one and the chassis rebooted... so your milage may vary. Sometimes it works, sometimes it doesn't, even if they are on the same power source. Joshua Coombs On Monday 07 April 2003 08:32 am, alex(a)wanex.ge wrote: > This chassis is connected to 2 UPS-s in case of 1 fails another will > work. What will happen if voltage (or amperage or freq.) of one UPS is > different from another? > > > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

Hiper Chassis Blowout!!!
by sky1 07 Apr '03

07 Apr '03

Got more Hiper Chassis to move!!! Pricing breakdown: Quantity (1) $3750.00 Quantity of (2-3) $3500.00 ea Quantity of 4-10 $3250.00 ea Fully loaded Hiper Chassis Configured as follows: (14) Hiper DSP T-1 Card Sets (2) Hiper ARC 128 Mb Version (1) Hiper NMC (2) 130 Amp AC power supplies (1) "Blue" Labeled chassis w/ integrated Fan tray Hiper DSP Cards $175.00 each Hiper ARC Sets (128 MB Version) $125.00 each All equipment in excellent condition....6 month warranty. If interested, contact: Shannan Young SouthWest Data Technology, Inc. 972-739-7010 972-739-7013 (Fax) sky1(a)airmail.net www.swdt.com

1 0

Frozen Console
by Rogerio Carvalho 05 Apr '03

05 Apr '03

Hi all I have a Total Control Enterprise Network Hub, when i try to start a console in NMC or in the NetServer the first message apears like that menu of NMC but after that the console frozen and i cant do nothing, i tried all ways to fix that like change speed, dip switches, cables but nothing happens, if someon could help me... []'s --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com) Version: 6.0.467 / Virus Database: 266 - Release Date: 01/04/03

2 1

FS: TC1000 DS-3 Ingress Card sets
by Stephen Rivera - WRCA.Net 04 Apr '03

04 Apr '03

Available now. DS-3 Ingress Card Nac P/N: 69-004086-01 DS-3 Ingress Nic P/N: 69-004085-00 60 sets Available $3500 Each Set 6 month warranty FYI: I am still looking to buy 2- 3COM 3C0504222-00 MultiSpan card sets. If you have some to move let me know please. Also buying quad modem fan out cables (4 port RS232) and Analog/Digital modem sets. Look forward to hearing from you. ********************************************************************* Steve Rivera IM: srivera711 (877)WRCANET x102 for more product info got www.wrca.net WRCA , Inc. - 481 Wright Debow Rd. Jackson, NJ 08527

1 0

IPSec
by Justin Wheeler 04 Apr '03

04 Apr '03

One of my customers has a VPN he uses on the Internet using IPSec. Do I need to enable/config anything special so that he may do that? Regards, Justin Wheeler -- Computer programmer (n): Red-eyed mammal capable of communicating with electronics and inanimate equipment.

1 0

RE: [USR-TC] hd020019.dmf
by RickL＠solunet.com 03 Apr '03

03 Apr '03

Be glad you couldn't find that file to revert too. DOORSTOP!! Rick -----Original Message----- From: Joel - Fox Computers [mailto:jfox@foxcomputers.com] Sent: Thursday, April 03, 2003 2:19 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: RE: [USR-TC] hd020019.dmf yeah- that's what I was talking about... -----Original Message----- From: Adam Barnhill [mailto:adam@semo.net] Sent: Thursday, April 03, 2003 1:12 PM To: 'Discussion relating to the 3Com/US Robotics Total Controlmodemsystems.' Subject: RE: [USR-TC] hd020019.dmf Downgrading Code You may find it necessary to revert back to Total Control 1000 Release 4.3 code on either the DSP multispan card or the HiPer DSP card. Follow these steps to revert back: 1 Flash to Total Control 1000 4.3 compatible code. (Previous versions are not usable until the card successfully loads/boots 3.1.x code.) 2 Before you upload the code you must log into the console, or telnet, and enter the following commands: chdev mdm1 at-re1 3 After the prompt returns, initiate the code download as usual and reboot when it is completed. -- Adam Barnhill Support Engineer, TotallyFabricated.com Information Technology Engineer, Poplar Bluff Internet, Inc. / Semo.net P.O. Box 190 | Poplar Bluff, MO 63902 | 573.686.9114, < http://www.semo.net/ <http://www.semo.net/> > Home of TotallyFabricated.com the creators of Total Scrutinizer -----Original Message----- From: usr-tc-bounces(a)mailman.xmission.com [mailto:usr-tc-bounces@mailman.xmission.com] On Behalf Of Joel - Fox Computers Sent: Thursday, April 03, 2003 12:28 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: RE: [USR-TC] hd020019.dmf Warning - I don't know what it is, but there are some specific config changes you have to make to a card to downgrade from 3.5.x. I think someone said something about turning them into doorstops if you do this wrong. I'd recommend re-uploading the 3.5.x first. Also - 3.5.12 is the devil - you should go 3.5.105 or 3.5.109. - Joel -----Original Message----- From: David Swearingin [mailto:david@carolnet.com] Sent: Thursday, April 03, 2003 11:26 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] hd020019.dmf I tried upgrading from hd020019.dmf on a HiPerDSP to hd030512.dmf. Now the card doesn't work at all. I want to revert back to the hd020019.dmf but I can't find my file. Can someone email me this file? Thanks.

1 0

RE: [USR-TC] hd020019.dmf
by Joel - Fox Computers 03 Apr '03

03 Apr '03

yeah- that's what I was talking about... -----Original Message----- From: Adam Barnhill [mailto:adam@semo.net] Sent: Thursday, April 03, 2003 1:12 PM To: 'Discussion relating to the 3Com/US Robotics Total Controlmodemsystems.' Subject: RE: [USR-TC] hd020019.dmf Downgrading Code You may find it necessary to revert back to Total Control 1000 Release 4.3 code on either the DSP multispan card or the HiPer DSP card. Follow these steps to revert back: 1 Flash to Total Control 1000 4.3 compatible code. (Previous versions are not usable until the card successfully loads/boots 3.1.x code.) 2 Before you upload the code you must log into the console, or telnet, and enter the following commands: chdev mdm1 at-re1 3 After the prompt returns, initiate the code download as usual and reboot when it is completed. -- Adam Barnhill Support Engineer, TotallyFabricated.com Information Technology Engineer, Poplar Bluff Internet, Inc. / Semo.net P.O. Box 190 | Poplar Bluff, MO 63902 | 573.686.9114, < http://www.semo.net/> Home of TotallyFabricated.com the creators of Total Scrutinizer -----Original Message----- From: usr-tc-bounces(a)mailman.xmission.com [mailto:usr-tc-bounces@mailman.xmission.com] On Behalf Of Joel - Fox Computers Sent: Thursday, April 03, 2003 12:28 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: RE: [USR-TC] hd020019.dmf Warning - I don't know what it is, but there are some specific config changes you have to make to a card to downgrade from 3.5.x. I think someone said something about turning them into doorstops if you do this wrong. I'd recommend re-uploading the 3.5.x first. Also - 3.5.12 is the devil - you should go 3.5.105 or 3.5.109. - Joel -----Original Message----- From: David Swearingin [mailto:david@carolnet.com] Sent: Thursday, April 03, 2003 11:26 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] hd020019.dmf I tried upgrading from hd020019.dmf on a HiPerDSP to hd030512.dmf. Now the card doesn't work at all. I want to revert back to the hd020019.dmf but I can't find my file. Can someone email me this file? Thanks.

1 0

RE: [USR-TC] hd020019.dmf
by Joel - Fox Computers 03 Apr '03

03 Apr '03

Warning - I don't know what it is, but there are some specific config changes you have to make to a card to downgrade from 3.5.x. I think someone said something about turning them into doorstops if you do this wrong. I'd recommend re-uploading the 3.5.x first. Also - 3.5.12 is the devil - you should go 3.5.105 or 3.5.109. - Joel -----Original Message----- From: David Swearingin [mailto:david@carolnet.com] Sent: Thursday, April 03, 2003 11:26 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] hd020019.dmf I tried upgrading from hd020019.dmf on a HiPerDSP to hd030512.dmf. Now the card doesn't work at all. I want to revert back to the hd020019.dmf but I can't find my file. Can someone email me this file? Thanks.

2 1