July 2002 - USR-TC - mailman.xmission.com

dsp console password
by Gen Camiling 10 Jul '02

10 Jul '02

there is no password on the console as the default you just have to press ENTER once you are prompted, unless of course it has been set previously. If so, try to restore settings back to factory defaults. -- Best regards, Gen ================================== Gen Camiling Chief Technical Officer International Micro Village, Inc. PHILIPPINES (63)(2) 7512130 mailto:gcamiling@imvi.com.ph ==================================

1 0

6 Channel Multilink
by Stephen Bader 10 Jul '02

10 Jul '02

We are trying to establish a 6 channel multilink connection using 3 ISDN lines. We are able to connect with 2 channels and get a 128K connection, but after we try to bring up the third channel, the connection becomes unuseable and soon disconnects. We are using a cisco router with 3 BRI interfaces, and have been working with Cisco to build a config that makes this work. They say it is possible and should work with our current config. My quetion is, has anyone else been able to do something like this? The most channels we have ever bonded has been 2, so I am not sure if there is something I am missing. Radius is authenticating the user just fine, so I don't believe it is a cause of the problem. Is this something that can be done? If so, are there any special configuration options I should be looking at? TIA, -Steve ------------------------------------------------------------------------- Stephen Bader JORSM Internet, Regional Internet Services Systems Administrator 7 Area Codes in Chicagoland and NW Indiana steveb(a)jorsm.com 100Mbps+ Connectivity, 56K-DS3, V.90, ISDN (219) 322-2180 Quality Service, Affordable Prices http://www.jorsm.com Serving Gov, Biz, Indivds Since 1995 -------------------------------------------------------------------------

3 5

Help with OLD gear
by Charles Sprickman 09 Jul '02

09 Jul '02

Hi, Looking for someone with good knowledge of Netserver-era TC stuff... I have an old 45A chassis with an NMC, Netserver PRI, and 6 "Quad Analog" cards (hw rev. 0.2.0 and 2.0.0) with analog NICs. These modems all show up as "AIP" on the Netserver. If I stick in a newer Quad Digital card in the chassis, it comes up fine as "ARP", but it's kind of useless, since it can't talk to an analog NIC. I don't go back that far, the oldest card I ever saw was a Quad Analog/Digital. Is there a chance that these analog cards were not made to work with the Netserver? I can talk to them on the DTE ports on the analog nics, so they work, but I don't see a way to tell them NOT to talk to the DTE ports but to use the packet bus. Someone also mentioned that they may talk to a Netserver, but NOT a Netserver PRI. Any truth in that? I just don't know about stuff that old, and any docs for this stuff are long gone from the Commworks site it seems. Thanks, Charles -- Charles Sprickman spork(a)inch.com

4 5

Re: [USR-TC] Information re: EdgeServers please
by Stephen Rivera - WRCA.Net 07 Jul '02

07 Jul '02

they come with the peripherals nic and 10baseT ethernet nic. Edgeserver pro would have somilar nics but the ethernet is 10/100. At 01:06 PM 7/5/2002 +1000, you wrote: >-----BEGIN PGP SIGNED MESSAGE----- >Hash: SHA1 > >Im looking at having a play with some older edgeservers.. (the older >486 based models).. > >Ive got the edgeserver NAC, but no nic for it... can anyone tell me >about them, or point me >in the direction of some edgeserver reference areas ?? > >What do they normally come with ? are they normally pre-loaded with >anything ? >are there any usr flash upgrades or anything i need to know about ? > >regards > >Steve > >-----BEGIN PGP SIGNATURE----- >Version: PGP 7.1.1 > >iQA/AwUBPSUNQLzZ2D1wrS2iEQJ88gCdGSO9lvrsSsN831Sq6kVWPqbNac8An3Bn >+c4/6Jy0KZElfmA1tCqIBtzp >=nEPl >-----END PGP SIGNATURE----- Steve Rivera IM: srivera711 Toll Free: (877)WRCANET x102 DIRECT: 732-833-2034 Fax available equipment to: (732)833-2115 for more product info got www.wrca.net

1 0

WTB - Dual E1 Nic
by Linknet Administration 07 Jul '02

07 Jul '02

Would anyone have or know where I can get hold of a dual E1 NIC With Thanks Peter Bundy The contents of this e-mail and its attachments are confidential and may be subject to legal professional privilege and copyright. It is intended solely for the addressee. Access to this e-mail and its attachment by anyone else is unauthorized. No representation is made that this e-mail or any attachment is free of viruses and other defects. Virus scanning is recommended and is the responsibility of the recipient. If you are not the intended addressee, any disclosure, usage, copying, distribution or any action taken or omitted to be taken in reliance on it, is prohibited. If you have received this communication in error, please advise the sender immediately by reply e-mail and delete this message from your computer. Thank you for your cooperation. LINKNET INTERNET SERVICE PROVIDERS 18 Tincogan Street Mullumbimby NSW 2482 AUSTRALIA Ph: +612 66843345 Fax: +612 66843503 postal:- PO Box 520 Mullumbimby NSW 2482 AUSTRALIA for Guaranteed customer support & Quality assured service http://www.linknet.com.au

2 1

Re: [USR-TC] Most honorable ARC OSPF masters
by Marshall Morgan 07 Jul '02

07 Jul '02

Maybe I should catch up with the list a little more often ... (i.e. look at last weeks posts Marshall!). Marshall Morgan Internet Doorway, Inc (aka NETDOOR) http://www.netdoor.com 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 ----- Original Message ----- From: "Marshall Morgan" <marshall(a)netdoor.com> To: <usr-tc(a)mailman.xmission.com> Sent: Saturday, July 06, 2002 11:44 PM Subject: Re: [USR-TC] Most honorable ARC OSPF masters > What does your config look like - I don't know that we have ever seen a > complete, working OSPF config to this list. > > Marshall Morgan > > Internet Doorway, Inc (aka NETDOOR) > http://www.netdoor.com > > 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 > ----- Original Message ----- > From: "Scott Trautman" <scott(a)gdinet.com> > To: <usr-tc(a)mailman.xmission.com> > Sent: Wednesday, July 03, 2002 12:40 PM > Subject: [USR-TC] Most honorable ARC OSPF masters > > > > I have attempted, and failed, to remove RIP from my network and replace > with > > OSPF. > > I am shamed and humiliated that I must now ask for assistance with so > surely > > simple a matter, belying my stupidity and laziness. > > If also not for my cowardice, I would beat myself silly for such offense > to > > sensible honorable people such as yourself. > > > > ARC: V5.2.102, v5.0.9 yesterday, same situation I do believe. IE, not a > bug > > I don't think. I bug in the setter-upper (me). > > > > I am talking with my OSPF neighbors (good), > > I am sending a route for my dialpool (so is sending <a> route via OSPF), > > but, > > RADIUS users with static IP's, no OSPF route is being sent. > > Local route being created, yes. > > Turn RIP back on, whammo, the Rip Route is there as pretty as can be. > > I looked around in HARM under OSPF, then the modem groups for options > > relating, just didn't find anything. > > I'm sure there's got to be some option I'm missing. > > Network option? > > Modem Group option? > > Radius option? > > Global option? > > > > Also, can I set an option for the ARC to not become the master/backup for > > OSPF? > > Jus' makes me nervous that it becomes the BDR, though surely it works > > fine.... > > > > Scott Trautman > > Global Dialog Internet > > scott(a)gdinet.com > > 608-240-4638 > > www.gdinet.com > > > > > > > > _______________________________________________ > > USR-TC mailing list > > USR-TC(a)mailman.xmission.com > > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > > >

1 0

Most honorable ARC OSPF masters
by Scott Trautman 07 Jul '02

07 Jul '02

I have attempted, and failed, to remove RIP from my network and replace with OSPF. I am shamed and humiliated that I must now ask for assistance with so surely simple a matter, belying my stupidity and laziness. If also not for my cowardice, I would beat myself silly for such offense to sensible honorable people such as yourself. ARC: V5.2.102, v5.0.9 yesterday, same situation I do believe. IE, not a bug I don't think. I bug in the setter-upper (me). I am talking with my OSPF neighbors (good), I am sending a route for my dialpool (so is sending <a> route via OSPF), but, RADIUS users with static IP's, no OSPF route is being sent. Local route being created, yes. Turn RIP back on, whammo, the Rip Route is there as pretty as can be. I looked around in HARM under OSPF, then the modem groups for options relating, just didn't find anything. I'm sure there's got to be some option I'm missing. Network option? Modem Group option? Radius option? Global option? Also, can I set an option for the ARC to not become the master/backup for OSPF? Jus' makes me nervous that it becomes the BDR, though surely it works fine.... Scott Trautman Global Dialog Internet scott(a)gdinet.com 608-240-4638 www.gdinet.com

3 2

restricting access to specif interface
by Gen Camiling 06 Jul '02

06 Jul '02

Got about two scenarios in here that need some suggestions and expert advice from the list: a. I will be doing Virtual Port Hosting services and i would like to restrict my clients' access to a specified number of interfaces as agreed upon. TC-1000 has 14 HiperDSP,HARC,HNMC with the latest codes on it. I would only allow him access to 3 HiperDSPs. Client will be given pilot number to dial-in for their access. Question: 1. How do i restrict the access of this particular client only to the given interfaces. And if a none allowed username dialed into those interfaces it would be rejected, call will be dropped? Im looking into the "set swithed interfaces" and "set modem" commands just not sure if it will do the trick. b. What if my client will be implementing pre-paid internet cards services, if i will implement a username/password on the interfaces, how will the accounting for these pre-paid users get tracked since in my understanding (please do correct me if it's wrong) if authentication was done locally TC does not provide accounting logs to the configured RADIUS server. -- Best regards, Gen ================================== Gen Camiling Chief Technical Officer International Micro Village, Inc. PHILIPPINES (63)(2) 7512130 mailto:gcamiling@imvi.com.ph ==================================

2 1

RE: [USR-TC] The Balanced vs. Unbalanced discussion/definition...
by Brian Becker 06 Jul '02

06 Jul '02

I knew I should have re-read my post before hitting send...but I was late for leaving for the Cardinals v. Dodgers game (Cards won 3-2). Anyway, had I spent a more "editor" time, I would have said: Just as a comment...IN THE AUDIO WORLD balanced is... I'm actually an EE/CompE by degree and I have NO MEMORY of EVER studying this. Guess that explains that 2.74 GPA! :) Brian Brian Becker President, Poplar Bluff Internet, Inc. http://semo.net P.O. Box 190 | Poplar Bluff, MO 63902 | 573.686.9114 -----Original Message----- From: usr-tc-admin(a)mailman.xmission.com [mailto:usr-tc-admin@mailman.xmission.com] On Behalf Of Dave Martin Sent: Thursday, July 04, 2002 11:45 AM To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] The Balanced vs. Unbalanced discussion/definition... >AHHHH!! So which one is it?? > >There has to be an EE on this list somewhere. Guilty as charged. Balanced signalling transmits a signal over a pair of conductors (usually referred to as "+" and "-") with opposite polarity in order to eliminate "common mode" distortion from external electromagnetic sources. EMF is induced equally in each of the two conductors and is cancelled out (to the extent of the common-mode rejection offered) at the receiving end of cable. No shield is technically required (unshielded twisted-pair [UTP] ethernet cabling is one example), but is often used, especially on analog (e.g. audio) cabling. >Charles > >-- >Charles Sprickman >spork(a)inch.com > > >On Thu, 4 Jul 2002, Brian Becker wrote: > >> Just as a comment...balanced is required to have a ground and a shield >> to be defined as balanced. Of course much of the audio gear can survive >> if the ground and shield are the same signal, but it is not part of the >> spec and all major recording studios will utilize separate and distinct >> paths for the ground and the shield to reduce the level of noise to its >> minimum. >> >> I am "Artist Formerly known as Brian Becker" with Benson Music Group, >> Nashville, (Christian Rock) and spent many hours working with top >> studios in Nashville & Houston...they would laugh at the thought of >> combining ground and shield. >> >> Brian Becker >> President, Poplar Bluff Internet, Inc. http://semo.net >> >> Home of TotallyFabricated.com Software & Web Design >> http://TotalScrutinizer.com - Tech Support Just Got Easier! >> >> POBox 190 - Poplar Bluff, MO 63902 - 573.686.9114 >> >> >> -----Original Message----- >> From: usr-tc-admin(a)mailman.xmission.com >> [mailto:usr-tc-admin@mailman.xmission.com] On Behalf Of Jeff Mcadams >> Sent: Wednesday, July 03, 2002 6:31 PM >> To: usr-tc(a)lists.xmission.com >> Subject: [USR-TC] The Balanced vs. Unbalanced discussion/definition... >> >> >> OK...this is probably rather off-topic, but there were a couple of >> different people participating, and it might be of interest to some, so >> feel free to delete if you're not interested. >> >> Talked (via email) to my uncle who works for Sweetwater Sound >> (http://www.sweetwater.com) and owns his own sound studio on the side, >> about the use of the term "balanced" in audio gear. >> >> He said that the term wasn't precisely defined (gee, sounds like the >> data world!), but that in his opinion it didn't require a ground line to >> be considered a balanced signal. He basically said that virtual every >> cable type that you'll run across in audio work *does* have a ground >> line (sometimes, its also the shield), so its kinda a moot point, but >> that its not strictly required. Indeed, he pointed out that it can be a >> *bad* thing to have ubiquitously connected ground lines in audio work. >> >> He pointed out that the local ground of one piece of equipment may not >> be the same as the local ground of another piece of equipment, so since >> they are both grounded through their AC line, connecting the ground line >> between the two pieces of equipment can result in a voltage and waveform >> across the ground line, which can result in a hum in the signal. >> >> He mentioned that the way they avoid this problem in his studio (plug: >> DSL Studios, http://www.dslstudios.com...hosted by IgLou ;) was to have >> every connection between different pieces of equipment run through patch >> bays. Each piece of equipment has its own ground (through the AC line), >> and the patch bay itself (a passive piece of equipment) is also ground, >> but that the ground line in the cable is *not* connected to the ground >> of the patch bay. This ensures that there is no continuous ground >> connection between two different pieces of equipment and avoiding a >> ground loop. >> >> FWIW, he pointed out the use of the balancing concept at >> http://www.equitech.com...specifically "balanced power", ie, rather than >> having a hot line at 120VAC and a ground, you have two hot lines at > > 60VAC, but in opposite phase. When the power supplies in the equipment >> run by this looks at the two lines, it still sees 120VAC, but the >> opposite polarity of the lines means that the "reactive currents" coming >> back out of the power supply end up cancelling each other out, resulting >> in a significant noise reduction. I found it interesting that there's a >> third field where balancing is used. >> >> Anyway...this is probably way more than most of you wanted to know, but >> I found the mental excursion interesting, hopefully others have found >> the discussion enlightening as well. >> >> Let me know if anyone has questions, if I can't answer them, I'll get >> better answers from my uncle...he's *quite* knowledgeable about audio >> production. :) >> -- >> Jeff McAdams Email: jeffm(a)iglou.com >> Head Network Administrator Voice: (502) 966-3848 >> IgLou Internet Services (800) 436-4456 >> >> _______________________________________________ >> USR-TC mailing list >> USR-TC(a)mailman.xmission.com >> http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc >> >> >> >> _______________________________________________ >> USR-TC mailing list >> USR-TC(a)mailman.xmission.com >> http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc >> > > >_______________________________________________ >USR-TC mailing list >USR-TC(a)mailman.xmission.com >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc -- ------------------------------------------------------------------------ Dave Martin Netcetera, Inc. dpm(a)netcetera.com "May the Foo be with you" ------------------------------------------------------------------------ _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

MPPP maximum lines?
by Theodore Cekan 05 Jul '02

05 Jul '02

Hello, What is the maximum number of lines that a HiperARC server can support in a MPPP session? Will it support 4? More? Thanks, Ted

3 2