- USR-TC - mailman.xmission.com

(usr-tc) Hiper ARC Questions
by Brad Gass 16 Jul '01

16 Jul '01

Hello, all. OK, this is probably going to sound *really* silly to all of you seasoned USR/3Com veterans out there, but it's a question about NetServers vs. Hiper ARC. As I understand it, and appear to have witnessed first hand, probably one of the wider known flaws of the NetServer's (even in the last official code release) was the UDP lag issues, and that a HiperARC doesn't exhibit this issue at all. I'm currently using Quad Digital Modem cards (mix of both single and double sided), latest firmware in them, PPP in modem, and v.90 enabled, in a 45A chassis So, I'm just verifying this before I go on a quest to find a reasonably priced Hiper ARC. Will the Hiper ARC will work with Quads? Do I need to have a Hiper NMC as well? Any special firmware/chassis requirements? What's the latest firmware revision of the Hiper ARC? I've got a few other questions as well, but I'll save those for separate threads later! Brad Gass - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

5 5

(usr-tc) FS: 3Com Hiper Bundles..Cisco Hot List
by ISP-NetworkHardware.com 13 Jul '01

13 Jul '01

Greetings: WRCA.Net has the following available to ship today. If you need anything Total Control, I have it. Hiper DSP sets $1800 Hiper ARC sets $1000 Hiper NMC sets $700 Chassis with 70A (AC) power $5500 Hiper NMC Hiper ARC 2x Hiper DSP Chassis with 70A (DC) power $5500 Hiper NMC Hiper ARC 2x Hiper DSP Chassis with Dual 45A power $1500 NMC v90 Netserver PRI Dual PRI 12x Quad Digital Modem 3- Cisco 1601 $500 1- Cisco 1005 $375 3- Cisco wic-1t $225 2- Cisco WIC-1DSU-T1 $425 9- Cisco 2501 $575 2- 2511 $1300 3- 2520 $1500 PA cards Lots more available. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Switching back to primary radius
by John Mies 12 Jul '01

12 Jul '01

My primary radius was down and was switched over to secondary. I can't switch the active server back to the primary. Using code 5.0.80. I've seen this question addressed before using the set radius command, but neither fall through or round robin will switch it back. Any suggestions? My current setup looks like this: Local Authentication is: ENABLED Remote Authentication is: ENABLED Hint Assigned is: DISABLED Primary Server is: 000.000.000.150 Primary Destination Port is: 1812 Secondary Server is: 000.000.000.10 Secondary Destination Port is: 1812 Tertiary Server is: 0.0.0.0 Tertiary Destination Port is: 1645 Source Port is: 1645 Retransmission Timeout: 3 seconds Max Retransmissions: 10 Per Server Retry Count 3 Vendor Specific Attribute: ENABLED Prioritize Auth Server: DISABLED Active Authentication Server: 000.000.000.10 Send service type indication: ENABLED Authentication Counters Syslogs: DISABLED Authentication Counters Syslog Frequency: TWELVE HOURS Authentication Counters Syslog Reset: DISABLED Primary Auth Server Preference: 1 Secondary Auth Server Preference: 2 Tertiary Auth Server Preference: 3 RADIUS SETTINGS Fill Null Attributes: DISABLED Attribute Style: STANDARD NAS Port Style : STANDARD Authentication Algorithm: ROUND_ROBIN Interim Accounting Interval Status: DISABLED Interim Accounting Interval: 240 seconds IEA Radius Source Port Authentication ENABLED IEA User Radius supplied username DISABLED Send Unauthenticated STOP record ENABLED Report Acct IP Addr only for Primary Link: DISABLED Send only STOP Acct for failed services: DISABLED DNIS Authentication Service Type: 10 Radius NAS-PORT id style: DENSITY BASED Radius Resource Reclaim style: DRAFT Radius Reboot Indication style: FALL-THROUGH Authentication Failure Trap State : ENABLED John Mies - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) ani config
by Wilson Diaz 10 Jul '01

10 Jul '01

Hi, excusme my english i have this problem , with hiper dsp , i have configuration it with e1 /r2 and i need get the ani number , i do the next procedure by my total contro manager , in the dsp card trunk settings in the option dial in address i check ani (also dnis and ani-dnis) but when i look register by one administation web page don´t show it , I speak with telco and say that they send the code . thanks

2 2

(usr-tc) Chassis Awareness?
by Mike Greene 09 Jul '01

09 Jul '01

Last Friday I posted a message to the list (it never showed up though) about a problem we saw with the TCH. Turns out the "Chassis Awareness" for the NMC was disabled. This happened Thursday night at 10:00pm. I took me a while to figure out what was wrong since everything else checked out OK. I did have a 2nd HARC installed, but not active. I was looking at the 'show nmc settings' command and noticed that the Chassis Awareness was disabled and remembered from my notes that it should be enabled. Issuing the command, 'enable nmc chassis_awareness' did nothing, but once I pulled the 2nd HARC out and issued the command again it accepted it and suddenly the system started taking calls again. What would cause the NMC to loose or have this setting disabled? Other than a malicious person changing it, but the system is protected with a good password and there was nothing in the logs to indicate that happened. - Mike ------------------------------------------------ Rock Island Communications, Inc. (360)-378-5884 http://www.rockisland.com/ San Juan Islands, WA ------------------------------------------------ - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

3 3

(usr-tc) DSP + ISDN DOVBS
by Charles Sprickman 09 Jul '01

09 Jul '01

Hi, Just a quick follow-on... Dug through what archives of the list I could find, but most of the info dealt with PRI card and quads. What I've found in digging around in TCM is: -general card settings->card level->call routing, offers up "call routing phone" and "call routing type". I've set type to digital, but still get modem tones when dialing. What should this be set to on a span that should only answer ISDN calls? -modem settings->ISDN Modem call control options->set data mode of modem, offers "autodetect, v.120, v.110, modem or fax only, aysyncsync PPP conv, and v.75". Any ideas on which one of these matches the typical home user dialing in with a router @ 56K? Again, ANY help or suggestions are appreciated! Thanks, Charles ---- Hi, We just had our Cisco 3620, which handled all of our ISDN calls, go up in smoke. I have a number of free DSP cards, so I decided I'd take our one PRI for ISDN and plug it into one of those. The good part is that I've got the trunk settings correct, as the telco sees everything OK, as do I. Calls are answered. My problem is forcing it to not answer with modem tones. All of our users are home users dialing "DOVBS" or basically placing a data call that looks (and most importantly is billed like) a voice call. Anyone have any hints on making ISDN go? The trunk is good, and I can do what I need in radius to get the routing going, it's just getting the thing to answer ISDN... Thanks, Charles | Charles Sprickman | Internet Channel | INCH System Administration Team | (212)243-5200 | spork(a)inch.com | access(a)inch.com - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Current Code Revs (Running)
by Marshall Morgan 08 Jul '01

08 Jul '01

What are most people running now on their T1 based HiperDSP, 128M ARC and HiperNMCs? We are using 2.1.9 DSP, 4.2.32-1 HiperARC (or 5.1.99-x) and 6.2.17 (or 7.2.8) HiperNMC. How long has your code level been stable at that release? Class Class ... Anyone, Anyone? Marshall Morgan Internet Doorway, Inc (aka NETDOOR) http://www.netdoor.com 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) DSP + ISDN DOVBS
by Charles Sprickman 06 Jul '01

06 Jul '01

Hi, We just had our Cisco 3620, which handled all of our ISDN calls, go up in smoke. I have a number of free DSP cards, so I decided I'd take our one PRI for ISDN and plug it into one of those. The good part is that I've got the trunk settings correct, as the telco sees everything OK, as do I. Calls are answered. My problem is forcing it to not answer with modem tones. All of our users are home users dialing "DOVBS" or basically placing a data call that looks (and most importantly is billed like) a voice call. Anyone have any hints on making ISDN go? The trunk is good, and I can do what I need in radius to get the routing going, it's just getting the thing to answer ISDN... Thanks, Charles | Charles Sprickman | Internet Channel | INCH System Administration Team | (212)243-5200 | spork(a)inch.com | access(a)inch.com - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) Available Hiper, Quad Bundles and cards
by Brian Becker 05 Jul '01

05 Jul '01

So there are two DSPs in the 70A AC bundle? Are they relatively new? -----Original Message----- From: owner-usr-tc(a)lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com] On Behalf Of ISP-NetworkHardware.com Sent: Thursday, July 05, 2001 12:31 PM To: us-tc Subject: (usr-tc) Available Hiper, Quad Bundles and cards WRCA.Net has the following 3Com hardware available: Hiper DSP sets (nac/nic)$1850 Hiper DSP nics $450 Hiper ARC $1000 Hiper NMC (nac only) $500 EdgeServer Pro with 2nics $1000 Quad Digital Modems $100 each Hiper Bundle with 70A (AC) power $6000 Hiper Bundle with 70A (DC) power $6500 INCLUDES: NMC Hiper ARC 2x Hiper DSP Quad Digital Bundles with dual 45a power $1250 Quad Analog/Digital with dual 45a power $1500 INCLUDES: nmc netserver pri dual pri/t1 12x Quad digital modems All spare cards and parts available - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Available Hiper, Quad Bundles and cards
by ISP-NetworkHardware.com 05 Jul '01

05 Jul '01

WRCA.Net has the following 3Com hardware available: Hiper DSP sets (nac/nic)$1850 Hiper DSP nics $450 Hiper ARC $1000 Hiper NMC (nac only) $500 EdgeServer Pro with 2nics $1000 Quad Digital Modems $100 each Hiper Bundle with 70A (AC) power $6000 Hiper Bundle with 70A (DC) power $6500 INCLUDES: NMC Hiper ARC 2x Hiper DSP Quad Digital Bundles with dual 45a power $1250 Quad Analog/Digital with dual 45a power $1500 INCLUDES: nmc netserver pri dual pri/t1 12x Quad digital modems All spare cards and parts available - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0