- USR-TC - mailman.xmission.com

(usr-tc) Looking for feedback
by Bennie Warren 30 Aug '01

30 Aug '01

I am new to this list. I am preparing to buy a TC1000 chassis with 2 Hiperarc cards, 2 DS3 Ingress cards and 7 DSP cards. My questions are, does anyone else have any configuration even close to this? Is everyone happy with the support they get? How about pitfalls? I was also looking for a much more active list, any inputs on that? Thanks for any input on these items. Bennie - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

4 3

Re: (usr-tc) V.92 - anyone there yet?
by Thomas_Goodman＠3com.com 30 Aug '01

30 Aug '01

V.92 was posted for Beta last week (August 23, 2001). I have asked for some official words to submit to this list. Anyone looking to be a part of the Beta would need to fill out the Beta form on Total Service. Min Requirements for V.92 HiPer DSP HiPer ARC w/ 128MB HiPer NMC or Multi-Span New ARC or 56bit VPN ARC 333MHz NMC Hardware Requirements for Multi-Span Blade (96-port card) HiPer ARC w/ 128MB HiPer NMC Note: Max number of ports that these cards will handle is 450 ports. ( you could add 4 multi-spans to a Total Control 1000 with 48 ports of HiPer DSP) The new 333MHz NMC and New ARC will handle 672 ports. More to follow. Tom Goodman RAS Specialist (United States) "Randy Cosby" <dcosby(a)infowest.com> on 08/20/2001 12:34:40 PM Please respond to usr-tc(a)lists.xmission.com Sent by: "Randy Cosby" <dcosby(a)infowest.com> To: usr-tc(a)lists.xmission.com cc: (Thomas Goodman/MW/US/3Com) Subject: (usr-tc) V.92 - anyone there yet? Has anyone installed the V.92 software? Can you give details of performance, problems, how the upgrade is done, etc? I'm also interested in hearing any experiences with the 96 port DSP's. What are the "practical" requirements (power, HARC, etc.) to run those? I've been off the list of a while, so apologies if this has been discussed before. Randy Cosby Developer Shed, Inc./InfoWest, Inc. 435-674-0165 x11 Fax: 435-674-9654 --- http://www.infowest.com http://www.devshed.com - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

12 16

(usr-tc) i need dsp
by Wilson Diaz 29 Aug '01

29 Aug '01

I am interested in acquiring 5 Hiper DSP E1 and 1Hiper ARC, also thank for information, as time of delivery and mode of payment. Thanks - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) V.92 - anyone there yet?
by Brian Becker 28 Aug '01

28 Aug '01

I agree. Tom is my pick for RAS-SERVER-CUSTOMER-SUPPORT Individual of the Year. See you in a less than two months Tom! ISPConVegas. Let it ride on Red, BABY!!!! Brian Becker President, Poplar Bluff Internet, Inc. P.O. Box 190 | Poplar Bluff, MO 63902 | 573.686.9114 Home of http://semo.net - Southeast Missouri's Online Community http://TotallyFabricated.com Total Scrutinizer - Tech Support Just Got Easier WebGabber - All-html Web Chat Software -----Original Message----- From: owner-usr-tc(a)lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com] On Behalf Of Jeff Mcadams Sent: Tuesday, August 28, 2001 2:54 PM To: usr-tc(a)lists.xmission.com Subject: Re: (usr-tc) V.92 - anyone there yet? Also sprach Seth Jacobs >I don't really disagree with what being said here, but here we finally >have someone from 3Com offering to provide useful information. Tom >isn't the cause of the problem. And I'll strongly "amen" this statement. Tom has been absolutely *wonderful* to deal with over the years (we dealt with him back before USR was purchased by 3Com), and has almost always worked for the good of his customers...even taking battles very strongly up the chain of command within 3Com. Unfortunately, the chain of command for support issues ends at Al Huefner and Irfan Ali. These people are the problem, not Tom. -- Jeff McAdams Email: jeffm(a)iglou.com Head Network Administrator Voice: (502) 966-3848 IgLou Internet Services (800) 436-4456 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) OSPF sendpolicy question/problem
by Charles Sprickman 28 Aug '01

28 Aug '01

Hi, I'm running ARC 4.2.32, and I'm seeing some odd things with OSPF and sendpolicy matching. For example, here's my current sendpolicy: HiPer-1>> list osPF seNDPOLICY OSPF Send Policies: Source Address/Mask Action LOCAL x.x.193.000/C Advertise LOCAL x.x.195.000/C Do Not Advertise LOCAL x.x.197.000/C Do Not Advertise LOCAL x.x.199.000/C Advertise If I put a test user in x.x.193.0/24 somewhere, the host route is propogated to the neighbor (Cisco) fine. If I put the test user in x.x.199.0/24, it is not. Looking at the database on the cisco, I do not see the route at all. If I remove all the sendpolicy's, the x.x.199.x user's host route does propogate. I also have the two class C's that I do NOT want advertised, and the arc is spewing all the /32's at the cisco. O E1 x.x.195.17/32 [110/11] via x.x.208.3, 00:04:07, Ethernet0 O E1 x.x.195.19/32 [110/11] via x.x.208.3, 01:44:01, Ethernet0 O E1 x.x.195.29/32 [110/11] via x.x.208.3, 00:31:21, Ethernet0 O E1 x.x.195.30/32 [110/11] via x.x.208.3, 00:28:10, Ethernet0 O E1 x.x.195.25/32 [110/11] via x.x.208.3, 00:00:14, Ethernet0 O E1 x.x.195.26/32 [110/11] via x.x.208.3, 01:41:09, Ethernet0 O E1 x.x.195.27/32 [110/11] via x.x.208.3, 00:12:11, Ethernet0 Is this functionality just broken? I've not been brave enough to enter the world of 5.x arc code yet, and I don't want to go there unless I know it fixes any serious OSPF issues besides the DR/BDR problem... More ospf config info: on cisco, the arc's area is a stub. on arc: HiPer-1>> show osPF gloBAL GLOBAL OSPF SETTINGS Router ID: x.x.208.3 Administrative Status: ENABLED OSPF Version Number: 2 Area Border Router Status: DISABLED Autonomous System Border Router Status: ENABLED Type-of-service (TOS) Support: OFF External LSDB Limit: -1 Multicast Extensions Support: OFF Exit Overflow Interval: 0 Router's Support for OSPF Demand Routing: OFF OSPF Traps: DISABLED HiPer-1>> show osPF inTERFACE x.x.208.3 OSPF INTERFACE SETTINGS Interface IP Address: x.x.208.3 Addressless Ifindex: 0 Area ID: 0.0.0.1 Interface Type BC Administrative Status: ENABLED Router Priority: 0 Transit Delay: 1 Retranmit Interval: 5 Hello Interval: 10 Router Dead Interval: 40 OSPF Interface State: OtherDsgRtr Designated Router Address: x.x.208.1 Backup Designated Router Address: NONE Authentication Type: None OSPF Interface Demand: OFF OSPF Interface Metric TOS: 0 OSPF Interface Metric Value: 10 Any ideas? Thanks, Charles | Charles Sprickman | Internet Channel | INCH System Administration Team | (212)243-5200 | spork(a)inch.com | access(a)inch.com - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) OSPF problems
by Charles Sprickman 27 Aug '01

27 Aug '01

Hi, I'm running ARC 4.2.32, and need to set up a very simple ospf setup for static IP customers. The other end is a cisco router. Doing a debug on the cisco shows me this: OSPF: Hello from 216.223.208.3 with mismatched Stub/Transit area option bit OSPF: Send with youngest Key 2 OSPF: Hello from 216.223.208.3 with mismatched Stub/Transit area option bit OSPF: Send with youngest Key 2 Eh? Any ideas? Is OSPF broken or can I not make the USR a stub? Charles | Charles Sprickman | Internet Channel | INCH System Administration Team | (212)243-5200 | spork(a)inch.com | access(a)inch.com - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 3

(usr-tc) Callback w/Harc
by Jóhannes Rögnvaldsson 27 Aug '01

27 Aug '01

Hi My system has: Dual Pri HARC 3Com SA server (forwards auth req to ACE server) Has anyone successfully set up a system with callback! When I define a callback user locally on the HARC I get disconnected immediately, the HARC calls back but the dialin client doesn't answer because the session was disconnected immediately! add user "test" password "test" type network,callback set user test phone_number "5555555" When I try to do this on the SA server it seems to have no effect at all, the user type is "framed,callback", I set the callback phone number in the "callback" window. I dial in and get connected right away. I don't even get disconnected. Thanks Johannes Rognvaldsson LAN/WAN Specialist EJS hf - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) New list member
by Doug_Hensley＠GENERALHEALTH.ORG 24 Aug '01

24 Aug '01

Good afternoon to the list. I'm not sure whether anyone is on here now or not. I am about to put back into service a USR TC rackmount 32 and seeking software, software updates, etc. for same. Thanks in advance for any leads, Doug Hensley System Engineer PHNS Baton Rouge - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

Re: (usr-tc) Flashing Hyper Arc
by Jonathan Byrne 23 Aug '01

23 Aug '01

Steve Johnson (linuxnut(a)sonic.net) wrote: > smoothly untill I hit 80% then I get an TFTP error, Access Violation and it I see also, but see it a lot less on 128 meg ARCs. If it's nearby, I just go there and flash it over the console port, which works fine. Cheers, Jonathan -------- <PLUG TYPE="shameless"> Leaving Japan end of September, available for employment in California. </PLUG> - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) FS: USR/3Com Total Control, MP, Netservers and more.
by Mark E. Levy 15 Aug '01

15 Aug '01

> WTB: HIPER NMC sets I need to upgrade to the P5 HiperNMC. I currently have the 486-based Hiper NMC. Please quote a price for the upgrade. -- Mark E. Levy FSInet, Inc. 800-827-6085 x202 847-753-6832 fax www.fsi.net mark(a)fsi.net - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0