- USR-TC - mailman.xmission.com

(usr-tc) Callback with HiperArc
by Erin Grooms 26 Oct '01

26 Oct '01

I've been trying to add a callback user with a static IP address to one of my hiperarcs, but have been having a couple of problems. I have a radius server as well, and I think it's skipping looking locally at all for the user. I get a basic authentication error when I try to dial-up (or telnet). Here is the basic config for the user I've got so far: INFORMATION FOR USER: callbacktest Status: INACTIVE Type: LOGIN NETWORK CALLBACK Expiration: NONE Message: this is a test DNIS Re Authentication: NO_REAUTH Special Xon Xoff Flow Control DISABLED Telnet Options: INVALID (D) Callback Type: STATIC Phone Number: "xxx-xxxx" Alternate Phone Number: (D) Input Filter: (D) Output Filter: (D) Modem Group: all (D) Session Timeout in seconds: 86400 Idle Timeout in seconds: 86400 Tap Status: DISABLED Tap Format: ASCII Tap Output: SYSLOG Tap Facility: LOG_AUTH Tap Loglevel: VERBOSE Port Limit: 2 Tap Address: 0.0.0.0 (D) Chat Script Name: PARAMETERS FOR LOGIN USERS: Login Service: TELNET TCP Port: 23 (D) Terminal: vt100 (D) Login Host Name: Login Host: 0.0.0.0 (D) Host Type: SELECT (D) PARAMETERS FOR NETWORK USERS: Network Service PPP Header Compression: TCPIP (D) Spoofing: DISABLED (D) MTU: 1514 (D) IP Usage: ENABLED (D) Address Selection: SPECIFIED Remote IP Address: 216.69.xxx.xx/H Next Hop Gateway IP Address: 0.0.0.0 (D) IP Routing: NONE (D) IP Routing Protocols: RIPV1 (D) IP RIP Routing Policies: IP RIP Authentication Key: Default Route Option: DISABLED (D) IGMP Query Interval: 125 seconds IGMP Max Response: 10 seconds IGMP Version: 2 IGMP Robustness: 2 IGMP Routing: DISABLED (D) Multicast Forwarding: DISABLED (D) Multicast Proxy: DISABLED (D) IPX Usage: ENABLED (D) IPX Address: 00000000 (D) IPX Routing: RESPOND (D) IPX WAN Usage: DISABLED (D) IPX RIP Update: 60 seconds IPX RIP Age Multiplier: 4 IPX SAP Update: 60 seconds IPX SAP Age Multiplier: 4 PARAMETERS FOR TUNNEL USERS: Tunnel Type: None (D) PARAMETERS for NETWORK PPP USERS Max Channels 2 (D) Channel Decrement Percent: 0 (D) Channel Expansion Percent: 0 (D) Expansion Algorithm: CONSTANT (D) Receive ACC Map: ffffffff (D) Transmit ACC Map: ffffffff (D) Compression Algorithm: AUTO (D) Compression Reset Mode: AUTO (D) Min Compression Size: 256 (D) Encryption Algorithm: NONE (D) Primary DNS Server: 216.69.xxx.xx Secondary DNS Server: 216.69.xxx.xx Periodic CHAP Timeout: 0 (D) Source Ip Address Filter: DISABLED (D) I'm mostly confused about the (D)'s everywhere, I haven't really dug very deep on my TCS boxes as far as adding extra users and such. Is there anything else I need to do on the user end, or on the hyperarc? I'm using version V4.2.32 of the firmware. Any help would be very appreciated. thanks! Erin Grooms System Administrator Erin Grooms System Administrator - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) test - delete
by Brian Becker 25 Oct '01

25 Oct '01

Your T1 is working, but I'm not sure I heard the modem pick up. Try switching to B8ZS! -----Original Message----- From: owner-usr-tc(a)lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com] On Behalf Of Blake Fithen Sent: Thursday, October 25, 2001 6:00 PM To: usr-tc(a)lists.xmission.com Subject: (usr-tc) test - delete test - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) FS: Total Control Hardware - WTB: Hiper NMC's! - Patton Available
by ISP-NetworkHardware.com 25 Oct '01

25 Oct '01

WRCA.Net has the following USR in stock, ready to ship. I know most of us are happy with USR/3Com but their a few ;) that have asked questions regarding Patton. WRCA.Net is now an authorized reseller of the Patton Products. I look forward to helping you with any questions you may have. PATTON HAS SEVERAL COMPETING MODELS, with some rare features like this... 2 YEAR FREE TECH SUPPORT FIRMAWARE UPGRADE, V92 STANDARD TRADE-IN PROMOTIONS $3500- $5000 FOR ANY COMPETITORS 48+PORT RAS FAIR MARKET VALUE FOR HARDWARE ON LEASE 2810 - 24 port $4500....2960 - 48 port $8500... 2996 - 96 port $14,000. Boxes can support T1, E1, CT1 as well as ISDN PRI line types. The units are complete with all software (pre-installed) and all hardware...including rack mount ears. Highlights: 1) Up to 96 Simultaneous connections on four T1/E1/PRI or Channelized T1 WAN lines. 2) 10/100 Full Duplex Ethernet port and RS232 Console Port 3) Built in SNMP/HTTP web management system 4) Supports Multilink-PPP and Multichassis for analog as well as ISDN calls. 5) Our dual and quad models are Convection Cooled -- Quiet 6) Dual redundant power supplies are standard and at no extra charge. 8) No worries with Patton's 30 Day "No Hassles" trial. 9) Financing information is available If you have any questions, or would like more detail on a specific model, please don't hesitate to contact me SRIVERA(a)WRCA.NET BACK TO THE SUBJECT AT HAND. Hiper DSP $1350 Hiper ARC $1200 64MB Hiper ARC $1600 128MB CellMux $700 Dual ADSL AxCell $700 130A power sets $600 70A power set $225 70A power sets (DC) - New In Box $350 45A Bundle, nmc, netserver pri, 12x quad digital modem, dual pri $850....This is a great box to consider for TRADE-IN for PATTON, They pay $5000 towards any of their RAS servers. 70a Bundle, nmc v90, netserver pri, 12x quad analog/digital modem, dual pri $1300 130A Bundle, nmc, hiper arc, 2x hiper dsp $5500 Netserver 8I $450 Netserver 16I $700 MP16 - Qty prices available. Managed MP16 $500 MP8 $350 MP8I $550 MP16I (International) $700 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) different IPs in start/stop accounting
by Charles Sprickman 22 Oct '01

22 Oct '01

Hello, Running HARC 4.2.32, I'm occasionally seeing sessions with the same session ID send one IP address in the START accounting message, and a different IP in the STOP accounting message. Has anyone else seen this? I'm trying to catch the box in the act so I can see which address the user is actually using, but so far no luck. I'm seeing this on multiple chassis, as well... Thanks, Charles | Charles Sprickman | Internet Channel | INCH System Administration Team | (212)243-5200 | spork(a)inch.com | access(a)inch.com - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) What memory does the HiperARC use?
by RickL＠solunet.com 16 Oct '01

16 Oct '01

Thanks for confirming Marshall. Sincerely, Rick -----Original Message----- From: Marshall Morgan [mailto:marshall@netdoor.com] Sent: Tuesday, October 16, 2001 2:34 PM To: usr-tc(a)lists.xmission.com Subject: Re: (usr-tc) What memory does the HiperARC use? On Mon, 11 Jun 2001, Mike Greene wrote: > Well the results are in! The proper memory chip is shown below... > > 128MB EDO 168pin BUFFERED 3.3v > > Popped that bugger in and inserted the card and presto, 128MB on the card, > the ROM memory is NOT replaceable but I don't see that as being a major issue. > > As a reseller I paid $143.00 per chip, your mileage may vary... > > > - Mike > > ------------------------------------------------ > Rock Island Communications, Inc. (360)-378-5884 > http://www.rockisland.com/ San Juan Islands, WA > ------------------------------------------------ > > Marshall Morgan Internet Doorway, Inc (aka NETDOOR) http://www.netdoor.com 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 ----- Original Message ----- From: <RickL(a)solunet.com> To: <usr-tc(a)lists.xmission.com> Sent: Tuesday, October 16, 2001 1:14 PM Subject: (usr-tc) What memory does the HiperARC use? > Hi, > Does anyone know the specs on HiperARC memory? > I know it is EDO, but: > Parity or Non-Parity ? > Gold Lead or Tin Lead ? > 5 volt ? > > Thanks, > Rick > > Rick Louizos > Solunet Soluserve TAC > Palm Bay, Fl. 32905 > Phone Numbers: > Phone: (888)449-5766 / Fax: (407)676-0809 > Internet Addresses: > mailto:RickL@solunet.com / http://www.solunet.com > > > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) What memory does the HiperARC use?
by RickL＠solunet.com 16 Oct '01

16 Oct '01

Hi, Does anyone know the specs on HiperARC memory? I know it is EDO, but: Parity or Non-Parity ? Gold Lead or Tin Lead ? 5 volt ? Thanks, Rick Rick Louizos Solunet Soluserve TAC Palm Bay, Fl. 32905 Phone Numbers: Phone: (888)449-5766 / Fax: (407)676-0809 Internet Addresses: mailto:RickL@solunet.com / http://www.solunet.com - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 1

RE: (usr-tc) What memory does the HiperARC use?
by RickL＠solunet.com 16 Oct '01

16 Oct '01

Thanks Mike. That helps. Rick -----Original Message----- From: Mike Greene [mailto:mikeg@rockisland.com] Sent: Tuesday, October 16, 2001 2:31 PM To: usr-tc(a)lists.xmission.com Subject: Re: (usr-tc) What memory does the HiperARC use? At 02:14 PM 10/16/01 -0400, you wrote: >Hi, >Does anyone know the specs on HiperARC memory? >I know it is EDO, but: >Parity or Non-Parity ? >Gold Lead or Tin Lead ? >5 volt ? 128MB EDO 168pin BUFFERED 3.3v Mine was tin lead, don't remember about parity though. - Mike ------------------------------------------------ Rock Island Communications, Inc. (360)-378-5884 http://www.rockisland.com/ San Juan Islands, WA ------------------------------------------------ - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) MRTG stats
by Mark Thornton 16 Oct '01

16 Oct '01

I have been using the hiperdsp.pl scripts included with the MRTG distibutions to track modem usage and it has always worked well until yesterday. About 10 p.m. the available modems value has dropped from 153 to 1. I have performed a software reset on the hipernmc and it did not fix the problem (it used to fix loss of communication on the old nmcs). Any ideas, or is there a better way to monitor modem utilization? Thanks, Mark Thornton San Marcos Internet, Inc 512-393-5300 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 4

(usr-tc) Converting T1/PRI card to CT1
by Brad Gass 13 Oct '01

13 Oct '01

Hello, all. Does anyone have CT1 (and possibly PRI as well) firmware available for the 386 version of the T1 cardset? I currently use a 186 powered CT1 card and am experiencing some general oddness with DS0->modem crossconnects being lost across power cycling the chassis, and want to try my spare 386 powered T1 card to see if it solves some of the strangeness I'm seeing. I'm down to that card as the last possible of the source of the problem I believe. My spare is loaded with PRI code, and I don't have PRI's available yet unfortunately, or I could use the spare as-is with some reprovisioning. The need for the PRI code as well is only preliminary now, but I'm told I should have PRI capability available soon in that CO, and would convert if I needed/wanted to service ISDN connections. I assume from reading the archives that there is no way of extracting the firmware from the card as it is now (PRI) so I can reload it if I do want to convert to PRI? Well, without the use of a soldering iron and a few hours at the bench anyway! I wonder why USR/3Com didn't just expand the size of the Flash (if they even needed to), and create firmware that could be used in both scenarios? As always, any and all help/suggestions is greatly appreciated! Brad - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Hiper DSP's $1200
by ISP-NetworkHardware.com 12 Oct '01

12 Oct '01

Subject says it all :) First come, First Served. Amex, Visa, Mastercard, COD 30 day warranty - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

3 2