- USR-TC - mailman.xmission.com

HELP! RADIUS logfile hitting 2GB in under 15 hours from USR attrib error!
by Giovanni Navarrette 26 Mar '02

26 Mar '02

Hello: I have this error coming into my logfiles, and i'm hitting the 2GB filesize limit in under 15 hours. Whats up with this error? Can I tell the HiPerARC to stop sending this, or is this something that my RADIUS server is going to have to control? I'm running Merit AAA 3.6B. Tue Mar 26 00:01:41 2002: generate26: USR attribute 39049 unknown Tue Mar 26 00:01:41 2002: gen_valpairs: non-encapsulated vendor specific attribute Vendor-Specific=vUSR-0000988900000000 Thanks :D ---------------------------------------------------- Giovanni Navarrette USLink Internet Systems Administrator e-Mail :: gio(a)uslink.net

2 1

LInk Timeouts
by Wayne Barber 26 Mar '02

26 Mar '02

I'm using the demo of Total Scrutinizer (which I like) and I've noticed the Link Timeout count keeps going up. Anyone know what that is measuring? Is it something about which I should be concerned? Thanks, Wayne Barber Coastal Telco Services

1 0

bad DSP?
by Mike Greene 23 Mar '02

23 Mar '02

Hello list members, I just acquired a used chassis with a few funky issues that I've managed to resolve but this one. I cannot seem to get this card to show "UP" for operational status, even though the remaining cards do (but are not plugged into telco T1's yet). The console port was showing down but I was able to clear that by doing a hardware reset, the modems on the other hand seem to be more difficult. I did pull the NIC and NAC out and it did not clear, is this DSP toast? Interface Oper Admin Name Status Status slot:4/mod:1 Down Up slot:4/mod:2 Down Up slot:4/mod:3 Down Up slot:4/mod:4 Down Up slot:4/mod:5 Down Up slot:4/mod:6 Down Up slot:4/mod:7 Down Up slot:4/mod:8 Down Up slot:4/mod:9 Down Up slot:4/mod:10 Down Up slot:4/mod:11 Down Up slot:4/mod:12 Down Up slot:4/mod:13 Down Up slot:4/mod:14 Down Up slot:4/mod:15 Down Up slot:4/mod:16 Down Up slot:4/mod:17 Down Up slot:4/mod:18 Down Up slot:4/mod:19 Down Up slot:4/mod:20 Down Up slot:4/mod:21 Down Up slot:4/mod:22 Down Up slot:4/mod:23 Down Up slot:4/mod:24 Down Up - Mike ------------------------------------------------ Rock Island Communications, Inc. (360)-378-5884 http://www.rockisland.com/ San Juan Islands, WA ------------------------------------------------

1 0

ISDN from a Cisco1604 won't connect second channel to HiPerDSP.
by WayneG 22 Mar '02

22 Mar '02

We are trying to connect a Cisco1604-ISDN Router to a TotalControl HiPerDSP. One channel comes up perfect, but the second channel is dropped immediately whenever it tries to connect. We can connect the 1604 to a Cisco3640 that has a BRI card in it, and it does 2 channels no problem. Also, we can also connect a 3Com Lan Router to the HiPerDSP and both channels work fine (even on different spans.) Cisco-to-Cisco is fine and 3Com-to-3Com is fine. But Cisco-to-3Com doesn't work. Go figure! Anyone have any suggestions? Thank you, -Wayne

2 1

Modem slot and Channels seem to be off by 1.
by Cyrus Smith 21 Mar '02

21 Mar '02

DS0-1 --> 1/1 end up on slot 2/1 Is this right? shouldn't my modems start in slot 2 and slot 1 should have "-"'s does anyone know what's wrong. Command> show modem Starting Slot: 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- S1 S5 S9 S13 S17 S21 S25 S29 S33 S37 S41 S45 - - - - S2 S6 S10 S14 S18 S22 S26 S30 S34 S38 S42 S46 - - - - S3 S7 S11 S15 S19 S23 S27 S31 S35 S39 S43 S47 - - - - S4 S8 S12 S16 S20 S24 S28 S32 S36 S40 S44 S48 - - - - I can't use for first slot (S1-S4) of modems. and the second span starts at S29 I do not have TCM Please can anyone help! Thank you! Cyrus.

2 4

Re: [USR-TC] NMC issues
by Kirk Mitchell 21 Mar '02

21 Mar '02

At 09:02 AM 3/21/02 -1000, Antonio Querubin wrote: >On Thu, 21 Mar 2002, Kirk Mitchell wrote: > >> Recently, shortly after moving to a new PRI provider, we've started >> experiencing strange drops. The only change made during the move was from >> DMS100 to NI2 on DSP settings, nothing else. What happens is that the NMC >> shows a red hub status light and everyone gets dropped. No other problem >> indications anywhere, DPS and ARC cards all green. This happens repeatedly >> 3-4 times in a period of about 5 minutes. After that, everything runs fine >> for a day or so, then cycle repeats. >> Has anyone seen anything similar? Any ideas? > >Might want to check where the timing on the local loop is coming from. Transmit clock source is set to loopTiming. Should that be different? Would that cause the NMC to go haywire and not the DSPs? Thanks, -- Kirk Mitchell-General Manager mitch(a)keyconn.net Keystone Connect Unlock Your World Altoona, PA 814-941-5000 http://www.keyconn.net

2 1

set packet_logging logging all work?
by Scott Trautman 21 Mar '02

21 Mar '02

What I'm trying to do: Get an idea of when packets are rejected from filters I'm using. Filters are assigned via RADIUS, and do work just fine. Use the following command: set packet_logging logging all Which is described as: set packet_logging logging [all | radius | none] packet_size [0-493 bytes] A description of each parameter follows. All - Creates SYSLOG messages globally for all filtered packets. Radius - Checks the RADIUS profile (Filter-Log-Packet attribute in the Access-Accept packet) on a per-user basis. None - No SYSLOG messages generated. 0-493 bytes - Use a number between 0 and 493 to specify how many bytes of the discarded packet to send to SYSLOG. Setting to 0 causes the entire packet to be included in the SYSLOG message. I see nothing in the syslog whatsoever relating to this other than a few sporadic: Mar 21 15:04:00 lkm-ha1 At 16:03:59, Facility "Filter Manager Process", Level "COMMON":: FM: No RADIUS rules available for user_handle=2bae06c, status=554d650c The filter DOES work, however, and I DID set the syslog to "verbose" (the above message came from that), but I'm really wondering if this command does anything at all. So, does this work, or, how do you debug filters other than "okay, it's just spinning now"...? SMT Scott M. Trautman President/Owner Global Dialog Internet scott(a)gdinet.com http://www.gdinet.com 2810 Crossroads, Suite LL2 Madison WI 53718 608-240-4638/800-482-4638 608-240-3637fax The Best in Broadband, Hosting and Dialup Internet Solutions for South Central and Eastern Wisconsin since 1995

1 0

Save changes to DSP
by Kirk Mitchell 21 Mar '02

21 Mar '02

Switching PRI providers and I need to change the switch type in my DSP's, can't seem to find where to save the new setting so it holds through a reset. Also, in switching from DMS100 to NI2, should there be any other trunk setting or other items I need to watch for? Thanks, -- Kirk Mitchell-General Manager mitch(a)keyconn.net Keystone Connect Unlock Your World Altoona, PA 814-941-5000 http://www.keyconn.net

5 7

OSPF adding local routes
by talist＠vif.com 21 Mar '02

21 Mar '02

I found a strange behaviour with the ospf process on the harc. I recently had to add the following commands on a cisco router on the network router ospf 1 redistribute static subnets [...] ip route 192.168.128.0 255.255.224.0 null0 220 out of a sudden, a new route is showing on the Harcs with: list ip route: 192.168.128.0/19 LOCAL 192.168.128.254 1 eth:1 This is bad because I now have to go through the gateway (cisco) for all local traffic. Also, I can't even remove the route unless I reboot the HiperArc: HiPer>> delete ip route 192.168.128.0/19 ERROR - Failed to delete the route to 192.168.128.0. Only routes marked as Static/NetMgt can be deleted.

1 0

MultiLink PPP
by WayneG 20 Mar '02

20 Mar '02

I am dialing BRI into a TC1000 HiPerDSP with a Cisco1604. The first channel comes up and stays fine, but the second channel comes up and drops almost immediately (1 to 4 seconds.) Is there anything special to do for a Two channel call? Thank you, -Wayne.

1 0