- USR-TC - mailman.xmission.com

Problems opening TCM with specific NMC/Chassis
by FIRST NOC TC Subscriber 12 Jul '02

12 Jul '02

We've got a chassis with 10 DSPs (2.1.9) and 2 HARCs (5.0.9) that I'm having trouble pulling up in the TCM. What is happening is that it bails out as soon as it gets to 'Retrieving NMC version'. I've reflashed the NMC. The NMC responds to normal SNMP queries (such as one would use with TCView). We did move around some cards in the chassis - but all DSPs ae the same configuration as they were before. I have rebooted the chassis numerous times after switching chassis awareness on and off (normally I run it off and set up the chassis slots statically on this particular chassis). Any suggestions? Thanks, Mike Tindor FIRST Internet ________________________________________________________________ Sent via the WebMail system at 1st.net

1 0

Last Request for Answers :) ...Hardware available.
by Stephen Rivera - WRCA.Net 11 Jul '02

11 Jul '02

Here are some of the items I will inquire about for the USR-list at the training. If you have any to add, email me. -Load balancing with multiple arc's -OSPF -Using TC box with MPPP to nail up a connection as a backup if main connection/route dies -MPIP (I think that's the protocol) -Troubleshooting the Telco's T1 or PRI -Filters also I have the following available... Hiper DSP $850..what? Yeah $850...Limited time. Hiper ARC 64x128MB $1000 Hiper NMC $1500 96 port bundles v92 compatible (software upgrade required) $6500 MultiSpan 96port cards $8000 Steve Rivera IM: srivera711 Toll Free: (877)WRCANET x102 DIRECT: 732-833-2034 Fax available equipment to: (732)833-2115 for more product info got www.wrca.net

1 0

HiperDSP console password
by pankaj 11 Jul '02

11 Jul '02

Hi all, I have TC1000 with HiperDSPs, now I want to access dsps through console. But its password protected , casue when I tried to access console its giving me promt for password. And I dont know password. Whats are the possible solution to access or to disable password. Thanks pankaj

2 2

dsp console password
by Gen Camiling 10 Jul '02

10 Jul '02

there is no password on the console as the default you just have to press ENTER once you are prompted, unless of course it has been set previously. If so, try to restore settings back to factory defaults. -- Best regards, Gen ================================== Gen Camiling Chief Technical Officer International Micro Village, Inc. PHILIPPINES (63)(2) 7512130 mailto:gcamiling@imvi.com.ph ==================================

1 0

6 Channel Multilink
by Stephen Bader 09 Jul '02

09 Jul '02

We are trying to establish a 6 channel multilink connection using 3 ISDN lines. We are able to connect with 2 channels and get a 128K connection, but after we try to bring up the third channel, the connection becomes unuseable and soon disconnects. We are using a cisco router with 3 BRI interfaces, and have been working with Cisco to build a config that makes this work. They say it is possible and should work with our current config. My quetion is, has anyone else been able to do something like this? The most channels we have ever bonded has been 2, so I am not sure if there is something I am missing. Radius is authenticating the user just fine, so I don't believe it is a cause of the problem. Is this something that can be done? If so, are there any special configuration options I should be looking at? TIA, -Steve ------------------------------------------------------------------------- Stephen Bader JORSM Internet, Regional Internet Services Systems Administrator 7 Area Codes in Chicagoland and NW Indiana steveb(a)jorsm.com 100Mbps+ Connectivity, 56K-DS3, V.90, ISDN (219) 322-2180 Quality Service, Affordable Prices http://www.jorsm.com Serving Gov, Biz, Indivds Since 1995 -------------------------------------------------------------------------

3 5

Help with OLD gear
by Charles Sprickman 08 Jul '02

08 Jul '02

Hi, Looking for someone with good knowledge of Netserver-era TC stuff... I have an old 45A chassis with an NMC, Netserver PRI, and 6 "Quad Analog" cards (hw rev. 0.2.0 and 2.0.0) with analog NICs. These modems all show up as "AIP" on the Netserver. If I stick in a newer Quad Digital card in the chassis, it comes up fine as "ARP", but it's kind of useless, since it can't talk to an analog NIC. I don't go back that far, the oldest card I ever saw was a Quad Analog/Digital. Is there a chance that these analog cards were not made to work with the Netserver? I can talk to them on the DTE ports on the analog nics, so they work, but I don't see a way to tell them NOT to talk to the DTE ports but to use the packet bus. Someone also mentioned that they may talk to a Netserver, but NOT a Netserver PRI. Any truth in that? I just don't know about stuff that old, and any docs for this stuff are long gone from the Commworks site it seems. Thanks, Charles -- Charles Sprickman spork(a)inch.com

4 5

Re: [USR-TC] Information re: EdgeServers please
by Stephen Rivera - WRCA.Net 07 Jul '02

07 Jul '02

they come with the peripherals nic and 10baseT ethernet nic. Edgeserver pro would have somilar nics but the ethernet is 10/100. At 01:06 PM 7/5/2002 +1000, you wrote: >-----BEGIN PGP SIGNED MESSAGE----- >Hash: SHA1 > >Im looking at having a play with some older edgeservers.. (the older >486 based models).. > >Ive got the edgeserver NAC, but no nic for it... can anyone tell me >about them, or point me >in the direction of some edgeserver reference areas ?? > >What do they normally come with ? are they normally pre-loaded with >anything ? >are there any usr flash upgrades or anything i need to know about ? > >regards > >Steve > >-----BEGIN PGP SIGNATURE----- >Version: PGP 7.1.1 > >iQA/AwUBPSUNQLzZ2D1wrS2iEQJ88gCdGSO9lvrsSsN831Sq6kVWPqbNac8An3Bn >+c4/6Jy0KZElfmA1tCqIBtzp >=nEPl >-----END PGP SIGNATURE----- Steve Rivera IM: srivera711 Toll Free: (877)WRCANET x102 DIRECT: 732-833-2034 Fax available equipment to: (732)833-2115 for more product info got www.wrca.net

1 0

WTB - Dual E1 Nic
by Linknet Administration 07 Jul '02

07 Jul '02

Would anyone have or know where I can get hold of a dual E1 NIC With Thanks Peter Bundy The contents of this e-mail and its attachments are confidential and may be subject to legal professional privilege and copyright. It is intended solely for the addressee. Access to this e-mail and its attachment by anyone else is unauthorized. No representation is made that this e-mail or any attachment is free of viruses and other defects. Virus scanning is recommended and is the responsibility of the recipient. If you are not the intended addressee, any disclosure, usage, copying, distribution or any action taken or omitted to be taken in reliance on it, is prohibited. If you have received this communication in error, please advise the sender immediately by reply e-mail and delete this message from your computer. Thank you for your cooperation. LINKNET INTERNET SERVICE PROVIDERS 18 Tincogan Street Mullumbimby NSW 2482 AUSTRALIA Ph: +612 66843345 Fax: +612 66843503 postal:- PO Box 520 Mullumbimby NSW 2482 AUSTRALIA for Guaranteed customer support & Quality assured service http://www.linknet.com.au

2 1

Re: [USR-TC] Most honorable ARC OSPF masters
by Marshall Morgan 06 Jul '02

06 Jul '02

Maybe I should catch up with the list a little more often ... (i.e. look at last weeks posts Marshall!). Marshall Morgan Internet Doorway, Inc (aka NETDOOR) http://www.netdoor.com 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 ----- Original Message ----- From: "Marshall Morgan" <marshall(a)netdoor.com> To: <usr-tc(a)mailman.xmission.com> Sent: Saturday, July 06, 2002 11:44 PM Subject: Re: [USR-TC] Most honorable ARC OSPF masters > What does your config look like - I don't know that we have ever seen a > complete, working OSPF config to this list. > > Marshall Morgan > > Internet Doorway, Inc (aka NETDOOR) > http://www.netdoor.com > > 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 > ----- Original Message ----- > From: "Scott Trautman" <scott(a)gdinet.com> > To: <usr-tc(a)mailman.xmission.com> > Sent: Wednesday, July 03, 2002 12:40 PM > Subject: [USR-TC] Most honorable ARC OSPF masters > > > > I have attempted, and failed, to remove RIP from my network and replace > with > > OSPF. > > I am shamed and humiliated that I must now ask for assistance with so > surely > > simple a matter, belying my stupidity and laziness. > > If also not for my cowardice, I would beat myself silly for such offense > to > > sensible honorable people such as yourself. > > > > ARC: V5.2.102, v5.0.9 yesterday, same situation I do believe. IE, not a > bug > > I don't think. I bug in the setter-upper (me). > > > > I am talking with my OSPF neighbors (good), > > I am sending a route for my dialpool (so is sending <a> route via OSPF), > > but, > > RADIUS users with static IP's, no OSPF route is being sent. > > Local route being created, yes. > > Turn RIP back on, whammo, the Rip Route is there as pretty as can be. > > I looked around in HARM under OSPF, then the modem groups for options > > relating, just didn't find anything. > > I'm sure there's got to be some option I'm missing. > > Network option? > > Modem Group option? > > Radius option? > > Global option? > > > > Also, can I set an option for the ARC to not become the master/backup for > > OSPF? > > Jus' makes me nervous that it becomes the BDR, though surely it works > > fine.... > > > > Scott Trautman > > Global Dialog Internet > > scott(a)gdinet.com > > 608-240-4638 > > www.gdinet.com > > > > > > > > _______________________________________________ > > USR-TC mailing list > > USR-TC(a)mailman.xmission.com > > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > > >

1 0

Most honorable ARC OSPF masters
by Scott Trautman 06 Jul '02

06 Jul '02

I have attempted, and failed, to remove RIP from my network and replace with OSPF. I am shamed and humiliated that I must now ask for assistance with so surely simple a matter, belying my stupidity and laziness. If also not for my cowardice, I would beat myself silly for such offense to sensible honorable people such as yourself. ARC: V5.2.102, v5.0.9 yesterday, same situation I do believe. IE, not a bug I don't think. I bug in the setter-upper (me). I am talking with my OSPF neighbors (good), I am sending a route for my dialpool (so is sending <a> route via OSPF), but, RADIUS users with static IP's, no OSPF route is being sent. Local route being created, yes. Turn RIP back on, whammo, the Rip Route is there as pretty as can be. I looked around in HARM under OSPF, then the modem groups for options relating, just didn't find anything. I'm sure there's got to be some option I'm missing. Network option? Modem Group option? Radius option? Global option? Also, can I set an option for the ARC to not become the master/backup for OSPF? Jus' makes me nervous that it becomes the BDR, though surely it works fine.... Scott Trautman Global Dialog Internet scott(a)gdinet.com 608-240-4638 www.gdinet.com

3 2