- USR-TC - mailman.xmission.com

RE: [USR-TC] Lost Carrier Terminations
by Joel - Fox Computers 30 Jul '02

30 Jul '02

Yes v.92 is enabled, and what's an XID timeout? THanks, Joel -----Original Message----- From: V [mailto:ved@iyka.com] Sent: Tuesday, July 30, 2002 10:03 PM To: usr-tc(a)mailman.xmission.com Subject: Re: [USR-TC] Lost Carrier Terminations Do you have v.92 enabled? Do you see an XID timeouts? -V ----- Original Message ----- From: Joel - Fox <mailto:jfox@foxcomputers.com> Computers To: usr-tc(a)mailman.xmission.com Sent: Tuesday, July 30, 2002 9:54 PM Subject: RE: [USR-TC] Lost Carrier Terminations I don't see any user unknown at all. I have 2 DSP's, code versions are 3.5.12 and 3.5.103. The 3.5.103 seems to be doing it a little more often, maybe 60% of the drops, probably a coincidence, but I'm going to update that tonight back to 3.5.12 if I can get these users off of it. I should also mention that although I have quite a few that are 11-30 seconds, I have some connections around 5 or 6 hours that this is happening to, the majority of them are 30-60 minutes and dropping off. Thanks, Joel -----Original Message----- From: V [mailto:ved@iyka.com] Sent: Tuesday, July 30, 2002 9:20 PM To: usr-tc(a)mailman.xmission.com Subject: Re: [USR-TC] Lost Carrier Terminations Lost Carrier - basically means that the connection was dropped due to loss of carrier - meaning the modems started connect and all of a sudden the connection was dropped by the connecting modem. A connection dropped within 11-30 sec is typically due to issues with modems, the LCP must not have started yet if you accounting time is set to before connection. What is the modem code on the DSP that you are using? Also are these logs for user "unknown" ? -V ----- Original Message ----- From: Joel - <mailto:jfox@foxcomputers.com> Fox Computers To: usr-tc(a)mailman.xmission.com Sent: Tuesday, July 30, 2002 8:50 PM Subject: [USR-TC] Lost Carrier Terminations So I'm looking at my RADIUS Accounting logs tonight. I see a lot of "Acct-Terminate-Cause = Lost Carrier", is this normal? Keep in mind, I have about 100 total users, max about 15 simultaneous, and I'm seeing about 250 (about 10%) occurances of this in 6 days. A LOT of the sessions are 11-30 seconds long. Is this normal? Do some modems just do this on disconnecting, or are there really that many people just losing their connections when they didn't want to??? Any ideas? Thanks, Joel

3 2

TC1000 hardware and service
by Stephen Rivera - WRCA.Net 30 Jul '02

30 Jul '02

In stock..30 day warranty pricing - 120day warranty available: For the newbies: I have a tech available for install & config...set fee / 2 hour time slot. You didnt have to buy the hardware from me. We can dial in or access via IP address. Whatever is easier for you. Limited time pricing on the DSP's, but I have lots. Hiper DSP $800...can negotiate for qty. Hiper ARC (128) $1000 Hiper ARC (64) $875 Hiper NMC $1400 MultiSpan96...lets talk :) ARC $3200 v90 Quad Digital (packs of 12) $600 WTB: Quad Analog/Digital Modem sets -w/ analog nic (daughtercard style) and FAN OUT cables for quad modems. 2x v92 bundles...This is how I bought them $6000. License of software..refer to TomG (3Com) post from last week. Chassis with Dual 130A power Hiper NMC Hiper ARC (128MB) 2x Hiper DSP v90 Hiper Bundles $4850 Chassis w/ dual 130A power Hiper NMC Hiper ARC 2x Hiper DSP v90 Quad Bundles $2000 Chassis w/ dual 70A NMC v90 enabled Hiper ARC (64MB) 12x Quad Digital modem I have lots of MP, netservers in stock too. Buying NETSERVER 16 v34's. Steve Rivera IM: srivera711 Toll Free: (877)WRCANET x102 DIRECT: 732-833-2034 Fax available equipment to: (732)833-2115 for more product info got www.wrca.net

1 0

Quad-Analog V.32terbo Modems with an ARC?
by Joel - Fox Computers 30 Jul '02

30 Jul '02

The Quad-Analog V.32 Modems, the ones with 4 RJ11's and a big multi-serial port on the back, if you put one of those in a chassis with an ARC, will it route incoming calls to the ARC rather than to the output on the back? Just curious, was thinking about using this for testing things like filters and such without messing with my production unit. Thoughts? Thanks, Joel

1 0

RE: [USR-TC] Association X 7/29/02
by Joel - Fox Computers 30 Jul '02

30 Jul '02

I think I missed something - will the data be collected through the site, or do you want the info now via email? -----Original Message----- From: Stephen Rivera - WRCA.Net [mailto:steverivera@wrca.net] Sent: Monday, July 29, 2002 7:39 PM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] Association X 7/29/02 UPDATE: I have been working with Charles Sprickman as of late on technical projects and he has offered to help out with the web page scripting. It will be a basic format with so far the following info in detail: Suggestions or concerns....dont be shy this is about you :) Publicly there will only be access to general info: # of companies, # of ports, popular software revision and or whatever you guys think. Privately the rest.. Have to trust us on this. If you need or want access that will be available at a phone request with faxed ID verification or a Publicly post request. AFTERALL WE ARE BEING WATCHED DATA TO BE COLLECTED Company name address city state zip phone fax President: CTO: Power in chassis -70A -130A Quad modem Ports -analog/digital -digital -software revision DSP Ports -software revision MultiSpan Ports - software revisions Hiper ARC -memory -software revision Hiper NMC - software revision Standard NMC -memory -software revision Dual PRI/T1/E1 -span (T1/PRI/E1 ) -software revision Other: -card type -software revision *****These are for me, so if I ever get equal opportunity as the little guy, I want to be sure I give you the service you expect. Gripe: What you would like to see come out of this user group: What could Commworks do better to make you happy? -Be specific This concept is only as good as you guys want it to be.. As a group we are not out to be-head anyone so keep that in mind....But I do need your DATA so be sure to get involved. We should have something up by tomorrow. The link will be on my main page at www.wrca.net (please excuse the bad links..experiencing technical difficulty) Header will be COMMWORKS TC1000 CLICK HERE. Oh yeah, I have DSP's, Hiper ARC's and Hiper NMC's available. Let me know if I can help you out. Since the service contracts arent on your agenda I am considering on offering 4 month warranties on my hardware. This would cover your a%&...on the hardware for a quarter of the year, but the software is still your responsibility. I'll tell it all, there will be an increase in price for the 4mths warranty but still reasonable. Steve Rivera IM: srivera711 Toll Free: (877)WRCANET x102 DIRECT: 732-833-2034 Fax available equipment to: (732)833-2115 for more product info got www.wrca.net _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

4 7

RE: [USR-TC] TC filter
by Vance McIndoe 30 Jul '02

30 Jul '02

Well, you're almost there. Don't apply the outgoing filter. Alternatively write an different outgoing filter that allows everything. (Just restrict the packets that you're dialin user sends :-) -- Vance McIndoe InterConnect Ltd Phone: +64-4-494-1144 Fax: +64-4-494-1140 Mobile: +64-27-2477-608 Street: Level 2, Exchange Place, 5-7 Willeston Street, Wellington, New Zealand. Postal: PO Box 5527, Lambton Quay, Wellington, NZ. <mailto:vancem@interconnect.co.nz> <http://www.interconnect.co.nz> -----Original Message----- From: Kancha . [mailto:kancha2np@yahoo.com] Sent: Tuesday, 30 July 2002 11:25 PM To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] TC filter Hello: After executing the following commands i could not browse or do anything. Couldnot even ping. Prior to executing these commands though the filters were applied i was able to do anything. set interFACE slot:1/mod:[1-23] filter_accESS on set interFACE slot:2/mod:[1-23] filter_ACCESS on enable ip address_pool_filtering save all reboot i'm running 5.1 of hyperArc __________________________________________________ Do You Yahoo!? Yahoo! Health - Feel better, live better http://health.yahoo.com _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc ###################################################################### Attention: This e-mail message is privileged and confidential. If you are not the intended recipient please delete the message and notify the sender. Any views or opinions presented are solely those of the author. ######################################################################

1 0

Anybody know what the Hex return part is on this OID?
by Lewis Bergman 30 Jul '02

30 Jul '02

When I do an snmpwalk <HiperARC ip> <community> .1.3.6.1.4.1.429.4.10.1.1.18 I get some user names with a hex part as shown below while most are just the user names. Anyone know what gives? enterprises.429.4.10.1.1.18.2553 = "smarsh" enterprises.429.4.10.1.1.18.2794 = "will" Hex: 77 69 6C 6C -- Lewis Bergman Texas Communications 4309 Maple St. Abilene, TX 79602-8044 915-695-6962 ext 115

1 0

RE: [USR-TC] TC filter
by Joel - Fox Computers 30 Jul '02

30 Jul '02

I'm assuming this is a filter for email-only accounts? But what's on port 53? Just curious, as this is something I'd like to be able to do also. -----Original Message----- From: Kancha . [mailto:kancha2np@yahoo.com] Sent: Monday, July 29, 2002 1:04 PM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] TC filter Hello: I created the filters and then applied is as well, but still doesn't work. This is the filter that i created. The filter was saved as email.fil.in and email.fil.out. #filter IP: 001 AND udp-dst-port = 53; 002 ACCEPT dst-addr = 192.168.1.3; 003 AND udp-dst-port = 53; 004 ACCEPT dst-addr = 192.168.1.4; 005 AND tcp-dst-port = 25; 006 ACCEPT dst-addr = 192.168.1.6; 007 AND tcp-dst-port = 110; 008 ACCEPT dst-addr = 192.168.1.3; 009 DENY; Then used command "add filter email.fil.in" and "add filter.fil.out" to add the filters to the filter table. Then from radius applied this filter to a user. When the user comes online the sessions shows the filter being applied, but the user can browse and do everything just like normal user. Below is the session. HiPer>> show session ispms INFORMATION FOR SESSION ispms Service Type: Framed Framed Protocol: PPP Idle Timeout: 900 Speed of Connection: Auto NAS IP Address: 192.168.1.5 Login Service: Telnet Interface Name: slot:2/mod:24 Active Session ID: 3541666 Traffic Threshold: 0 Keep Alive Interval: 0 Framed IP Netmask: 0.0.0.0 MLPPP Fragmentation Threshold: 0 Framed Routing: None Framed Callback Identifier: 0 Compression Algorithm: None Compression Reset Mode: Auto Filter Id Input: email.fil.in Receive Acc Map: 0 Transmit Acc Map: 0 Filter Id Output: email.fil.out have i missed out anything ?? what could be wrong ?? __________________________________________________ Do You Yahoo!? Yahoo! Health - Feel better, live better http://health.yahoo.com _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

5 5

Using separate IP-pools for different Modem-groups
by Patrick Ndegwa 30 Jul '02

30 Jul '02

Hi there. I have an interesting scenario for which I am not sure there is a solution. I have a 3Com chassis running Hiper ARC (ver 5.3.105) and a number of Hiper DSP cards (ver 3.5.13). The requirement essentially is to have users assigned an IP address based on the port they dial into on the NAS. I have setup 2 separate IP-pools on the Hiper ARC, and have setup 2 different modem-groups. Each of the modem-groups is associated with a separate dial-in number. Is there a way to link each modem group to its own IP-pool on the NAS? I have seen that the either of IP-pools can be prioritized, or set up for a round-robin usage but this is essentially not going to solve the problem. I think a solution may also exist where radius assigns an IP address from separate IP pools based on the user who is connecting. Any insight into this? Cheers, Patrick Ndegwa,

2 2

How to Enable PPP Compression?
by Joel - Fox Computers 29 Jul '02

29 Jul '02

Any ideas what has to be done to enable compression? I've heard that if your users get MPPC compression that the performance is much better. >From what I can find, looks like all I need is the CCP_MODEMTYPE_ACCEPT enabled, but it's not happening. Any ideas? Am I missing something here? When I look at any session, I see this: HiPer>> show session scottdodi INFORMATION FOR SESSION scottdodi Service Type: Framed Framed Protocol: PPP Session Timeout: 36000 Idle Timeout: 1800 Speed of Connection: Auto NAS IP Address: 216.81.189.29 4ass: C Login Service: Telnet Interface Name: slot:3/mod:16 Active Session ID: 4259861 Traffic Threshold: 0 Keep Alive Interval: 0 Framed IP Netmask: 0.0.0.0 MLPPP Fragmentation Threshold: 0 MaxChannels: 1 Framed Routing: None Framed Callback Identifier: 0 Compression Algorithm: None Compression Reset Mode: Auto Receive Acc Map: 0 Transmit Acc Map: 0

1 0

WANTED - USR TC NETSERVER 16
by Andy 29 Jul '02

29 Jul '02

An offline associate is looking for a USR TC Netserver with 16 or 8 analog ports. Ebay has a few auctions that end a week from now, and I'm trying to help find something more immediate. Please reply or call me directly at 801.303.0810. Thanks --- Andy Dalrymple XMission Telecom Manager Salt Lake City, UT

1 0