January 2005 - USR-TC - mailman.xmission.com

FW: [USR-TC] RE: Busy signal!!!
by Kirti S. Bajwa 23 Jan '05

23 Jan '05

Hello List: I did not receive any response to my post. In my last discussion with Sprint, they informed me that there is no setting they normally provide for an ISDN-PRI's. I have been changing settings to see if something works. I have some new findings: (1) I can test the 3Com with a UID/PW by using the "_auth UID PW" command (2) When I connect a ISDN-PRI line into HiPer DSP, the D-Channel gets locked. Then when I dial-into the line, it is /busy/. Is this information sufficient for somebody to give some hints? Thanks in advance. Kirti -----Original Message----- From: Kirti S. Bajwa [mailto:kbajwa@tib.com] Sent: Thursday, January 20, 2005 1:36 PM To: 'Discussion relating to the 3Com/US Robotics Total Control modem systems.' Subject: RE: [USR-TC] RE: Busy signal!!! Hello list: I am dead end. I posted this message over two months ago. I still have not been able to get settings from the telco (Sprint). Is there anybody in Tennessee who has a ISDN-PRI line (1D+23B) from Sprint? If you do, I appreciate if I can get the settings for the trunk from you!! If somebody has any other suggestion please let me know. Please respond. Thanks in advance. Kirti -----Original Message----- From: Todd Bertolozzi [mailto:berto@core.com] Sent: Wednesday, November 24, 2004 1:48 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] RE: Busy signal!!! I'd try to verify the dsp span settings with the telco. In particular things such as dnis/ani and the number of digits being sent by the switch. If you aren't on the same page with the telco as far as though settings go you can get busy signals. Todd ----- Original Message ----- From: "Kirti S. Bajwa" <kbajwa(a)tib.com> To: "'Discussion relating to the 3Com/US Robotics Total Control modemsystems.'" <usr-tc(a)mailman.xmission.com> Sent: Wednesday, November 24, 2004 12:42 PM Subject: RE: [USR-TC] RE: Busy signal!!! > Todd: > > Thank you for your reply. > > chassis awareness is ENABLED > list chassis does show port 23 > > Any other suggestion? > > Kirti > > -----Original Message----- > From: Todd Bertolozzi [mailto:berto@core.com] > Sent: Wednesday, November 24, 2004 11:52 AM > To: Discussion relating to the 3Com/US Robotics Total Control > modemsystems. > Subject: Re: [USR-TC] RE: Busy signal!!! > > > There could be a variety of things that cause this. How do you have your > chassis awareness setup? > > When you're in the arc and do a list chassis command does everything look > correct as far as number of ports=23, etc? > > Todd > ----- Original Message ----- > From: "Kirti S. Bajwa" <kbajwa(a)tib.com> > To: "'Discussion relating to the 3Com/US Robotics Total Control > modemsystems.'" <usr-tc(a)mailman.xmission.com> > Sent: Wednesday, November 24, 2004 11:20 AM > Subject: [USR-TC] RE: Busy signal!!! > > > > Hello List: > > > > I finally got 3Com box (1-HiPer NMC, 2-Hiper ARC & 10-Hiper DSP) setup. > > Today, I connected a T1-PRI ISDN line to test. But as soon as I connect, > the > > line gives busy signal. > > > > What setting causes this. /Please Help/. Thank you in advance. > > > > Kirti > > > > _______________________________________________ > > USR-TC mailing list > > USR-TC(a)mailman.xmission.com > > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

RE: [USR-TC] RE: Busy signal!!!
by Kirti S. Bajwa 20 Jan '05

20 Jan '05

Hello list: I am dead end. I posted this message over two months ago. I still have not been able to get settings from the telco (Sprint). Is there anybody in Tennessee who has a ISDN-PRI line (1D+23B) from Sprint? If you do, I appreciate if I can get the settings for the trunk from you!! If somebody has any other suggestion please let me know. Please respond. Thanks in advance. Kirti -----Original Message----- From: Todd Bertolozzi [mailto:berto@core.com] Sent: Wednesday, November 24, 2004 1:48 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] RE: Busy signal!!! I'd try to verify the dsp span settings with the telco. In particular things such as dnis/ani and the number of digits being sent by the switch. If you aren't on the same page with the telco as far as though settings go you can get busy signals. Todd ----- Original Message ----- From: "Kirti S. Bajwa" <kbajwa(a)tib.com> To: "'Discussion relating to the 3Com/US Robotics Total Control modemsystems.'" <usr-tc(a)mailman.xmission.com> Sent: Wednesday, November 24, 2004 12:42 PM Subject: RE: [USR-TC] RE: Busy signal!!! > Todd: > > Thank you for your reply. > > chassis awareness is ENABLED > list chassis does show port 23 > > Any other suggestion? > > Kirti > > -----Original Message----- > From: Todd Bertolozzi [mailto:berto@core.com] > Sent: Wednesday, November 24, 2004 11:52 AM > To: Discussion relating to the 3Com/US Robotics Total Control > modemsystems. > Subject: Re: [USR-TC] RE: Busy signal!!! > > > There could be a variety of things that cause this. How do you have your > chassis awareness setup? > > When you're in the arc and do a list chassis command does everything look > correct as far as number of ports=23, etc? > > Todd > ----- Original Message ----- > From: "Kirti S. Bajwa" <kbajwa(a)tib.com> > To: "'Discussion relating to the 3Com/US Robotics Total Control > modemsystems.'" <usr-tc(a)mailman.xmission.com> > Sent: Wednesday, November 24, 2004 11:20 AM > Subject: [USR-TC] RE: Busy signal!!! > > > > Hello List: > > > > I finally got 3Com box (1-HiPer NMC, 2-Hiper ARC & 10-Hiper DSP) setup. > > Today, I connected a T1-PRI ISDN line to test. But as soon as I connect, > the > > line gives busy signal. > > > > What setting causes this. /Please Help/. Thank you in advance. > > > > Kirti > > > > _______________________________________________ > > USR-TC mailing list > > USR-TC(a)mailman.xmission.com > > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

RE: [USR-TC] RE:IP Pool Settings!!
by Kirti S. Bajwa 18 Jan '05

18 Jan '05

Hello List: I am setting up a 3COM TC1000 Chassis with the following hardware: 1- HiPer NMC 2- HiPer ARC 10- Hipper DSP For testing purposes, I have set aside an ip pool from 12.21.237.168/C Size 72. How do I setup each HiPer ARC? Currently, when I setup HiPer ARC (using CLI to setup ARC), I assign 12.21.237.168 as 'Initial Address of IP Pool'. Is it correct or I should divide the IP Pool and assign a one block of IP addresses to one ARC and different block to the second ARC. Thanks. Kirti

2 1

Someone on this list contacted me with several edgeserver types available..
by Stephen Rivera - WRCA.Net 18 Jan '05

18 Jan '05

If your out there please contact me again. Looking for older edgeserver cards, no pro version. Thanks. Steve Rivera WR Consultant Associates, Inc. Dir: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

2 1

Anyone sitting on 33.6 Sportster external modems
by Stephen Rivera - WRCA.Net 17 Jan '05

17 Jan '05

Just trying to help you make space in those closets. Buying USR Sportster 33.6 modems with power supplies. Must be 33.6kbps version. Looking for Qty - working. Steve Rivera WR Consultant Associates, Inc. Dir: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

1 0

MOH problem
by Cyrus Smith 17 Jan '05

17 Jan '05

Everything seem to work fine, EXCEPT, if you take the call or not, after reconnect or reject call the modem hangs up after about 1 minute of working ok. D4 SF, dsp 3.5.109, arc 5.3.3, nmc 8.6.3

2 1

hyperarc ethernet port
by Geoffrey Deasey 17 Jan '05

17 Jan '05

My hyperarc has an aui port and a 10bast-t how do I force it to NOT use tha aui ? Thanks Geoffrey Geoffrey Deasey VP Systems Netpath, Inc. (336) 226-0425 www.netpath.net Alvarion certified wireless network engineer

7 8

RE: [USR-TC] 3com HiPer Access Router Manager (HARM)
by Kirti S. Bajwa 15 Jan '05

15 Jan '05

Did you get the software? If not, please contact me directly: kbajwa(a)tibonline.net -----Original Message----- From: Richard S. Dy [mailto:richard@sflu.com] Sent: Monday, January 10, 2005 5:36 AM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: Re: [USR-TC] 3com HiPer Access Router Manager (HARM) Hi, I'm also looking for the software for a long time, can you inform if you find it too, thanks Richard ----- Original Message ----- From: "Gerald Jaya" <gerry(a)zol.co.zw> To: "'Discussion relating to the 3Com/US Robotics Total Controlmodemsystems.'" <usr-tc(a)mailman.xmission.com> Sent: Monday, January 10, 2005 6:21 PM Subject: [USR-TC] 3com HiPer Access Router Manager (HARM) > Hi all > > I recently got a 3com TC 1000, I am looking for 3com HiPer Access Router > Manager (HARM) software, could you please help. I have been searching > desperately all over can seem to find it anywhere except for utstar.com, > who > won't let me download it > > > Thanks in advance > > Gerald. > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

RE: [USR-TC] TCM (Total Control Manager) vs CEM (Common Element Manager)
by Joel - Fox Computers 14 Jan '05

14 Jan '05

Steve, Just curious - what is the current, lowest price for the smallest license of CEM? Thanks, Joel -----Original Message----- From: Stephen Rivera - WRCA.Net [mailto:steverivera@wrca.net] Sent: Fri 1/14/2005 11:40 AM To: usr-tc(a)lists.xmission.com Cc: Subject: [USR-TC] TCM (Total Control Manager) vs CEM (Common Element Manager) For those of you wondering. at SOFTWARE LEVEL TCS 4.5 TCM will work fine. at CURRENT SOFTWARE LEVEL TCS 4.7 you need Common Element Manager The smallest license will support upto 5 SNMP nodes. CEM pricing has fallen, very reasonable. Available at your request. Feel free to contact me with any questions you may have. Steve Rivera WR Consultant Associates, Inc. Dir: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981. _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

2 1

TCM (Total Control Manager) vs CEM (Common Element Manager)
by Stephen Rivera - WRCA.Net 14 Jan '05

14 Jan '05

For those of you wondering. at SOFTWARE LEVEL TCS 4.5 TCM will work fine. at CURRENT SOFTWARE LEVEL TCS 4.7 you need Common Element Manager The smallest license will support upto 5 SNMP nodes. CEM pricing has fallen, very reasonable. Available at your request. Feel free to contact me with any questions you may have. Steve Rivera WR Consultant Associates, Inc. Dir: 732-833-2111 x102 IM: srivera711 www.wrca.net Providing Network Hardware Since 1981.

1 0