April 2001 - USR-TC - mailman.xmission.com

(usr-tc) stuck modems
by Dayton Internet 09 Apr '01

09 Apr '01

Not to start another discussions, but just to update one. What was ever resolved about a "pair of modems" (re port) in the hiperdsp's getting stuck in a mode that would not answer and would send out strange connection tones when dialed. The stuck modem would require the board to be reset to fix the situation. Was this determined to be in hardware or in software? Is there a version of hardware/software that is better/best? Was there a fix to prevent it from re-occuring? ---------------------------------------------------------- In the knowledge base, using "dsp modem not answering stuck" for a search key, I get 18 solutions: (Total search time 2.4 hours on a T1) 1. Upgrade HiPer ARC to 5.0.84-1 or newer code. I have 6.2.17 2. This message means that 1 of the DSP chips is not responding to the keep alive messages from the RISC. This is probably caused by a hardware failure. Reseat the DSP NIC and NAC and try a different slot. If the modem still shows the same reason for call failure,the DSP card must be replaced It happens on dsp hardware 49, 53,and 54, randomly. Do I need to replace all the cards as they happen? 3. This is fixed in HiPer DSP V2.0.60 I have 2.0.19 4. did not apply, ring no answer or busy on dsp 5. If during the AutoDetect Dialout sequence the switch responds with a Release Complete (Cause code 57), the HiPer DSP aborts the dialout attempt, and does not follow the *Ux settings. Fix 3Com is currently investigating this issue. Please refer to Technical Support for more information as it becomes available. (August 1999 answer) 6. install cards 7. reset cards 8. Total Control HiPer DSP - How to force a modem to dialout using different PIC codes. Nothing about stuck or not answering 9. Chassis Power Supply Upgrade Procedure DITTO! 10. 1.0.30365871.2192598 Title: Total Control EdgeServer PRO - What modem type should be selected when installing LANSource DITTO! 11. 1.0.25900539.2140685 Title: Total Control Chassis - Proper setup for HiPer DSP modem dial-out 12. 1.0.34816816.2254512 Title: Total Control HiPer DSP - Modems failing in pairs Current workarounds: issue AT command or software reset. Note: Emergency release code version 2.0.48 (or better) as well as the TCS 4.0 release of HiPer DSP code (version 2.1.9) incorporate the root cause fix for this problem June 2000 I have 2.0.19 Note: this addresses "dead air" and not incorrect tones All the rest did not apply 13. Title: Total Control HiPer DSP - Connect to HiPer DSP Console port via Modem Connection 14. 1.0.28239385.2169571 Title: Total Control HiPer ARC - How does Dynamic Slot Assignments for HiPer ARC Load Balancing work? 15. 2.0.63399864.3089714 Title: Total Control 1000 Enhanced Data System - Using templates to configure modems on HiPer DSP card. Nothing about stuck or not answering 16. 1.0.28400892.2170530 Title: Total Control HiPer ARC - How to setup Dynamic Slot Assignment (DSA)? 17. 1.0.30633781.2198069 Title: Total Control HiPer DSP - Use of the card session monitor on DSP modems 18. 2.0.10959488.2382699 Title: Total Control HiPer DSP - PBX or International calls requiring more than 15-16 digits fails via PRI dial-out -- --Rich Adams, President-Dayton Internet Services, Dayton, Ohio-- --w8mfd(a)dayton.net--www.dayton.net--www.dayton.com--937-586-2500-- - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

RE: (usr-tc) Commworks v.92 Announcement
by Mark E. Levy 09 Apr '01

09 Apr '01

It's my understanding that it will be free - if you have a service contract... > Of course it will be free! .... yeah right :-} > > Marshall Morgan > > Internet Doorway, Inc (aka NETDOOR) > http://www.netdoor.com > > 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax > 601.969.3838 > ----- Original Message ----- > From: "Mike Andrews" <mandrews(a)bit0.com> > To: <usr-tc(a)lists.xmission.com> > Sent: Thursday, April 05, 2001 6:09 PM > Subject: Re: (usr-tc) Commworks v.92 Announcement > > > > Hm. Q3 of 2001. No word on pricing. > > > > > > Mike Andrews * mandrews(a)dcr.net * mandrews(a)bit0.com * http://www.bit0.com > VP, sysadmin, & network guy, Digital Crescent Inc, Frankfort KY > Internet access for Frankfort, Lexington, Louisville and surrounding counties > www.fark.com: If it's not news, it's Fark. (Or something like that.) > > On Thu, 5 Apr 2001, Marshall Morgan wrote: > > > http://commworks.com/svprovider/news/apr0401b.html > > > > "COMMWORKS CORPORATION TO SUPPORT V.92 MODEM STANDARD ON ITS FLAGSHIP TOTAL > > CONTROL 1000 ENHANCED DATA SYSTEM" > > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

8 11

Re: (usr-tc) Commworks v.92 Announcement
by netboss＠cyberport.net 06 Apr '01

06 Apr '01

Patton is not going to eat anybodies lunch unless they get their 48 and 96 port models working. We had several units for about a month and could get nowhere the connection speeds that we got with our old Quad Modem cards. Proceed carefully with Patton. They are also slow to refund the money you paid in good faith. "Accounting" is never available to answer you questions about "where's the refund". At 11:09 AM 4/6/01 -0400, you wrote: >The market for 3COM gear should be flooded in the next year as most of the >year 1-2 HiperDSP leases expire. I'm giving up a chassis next month. >v.92 is not a good enough reason to stay 3COM with all the minuses that >come with the support/software. > >Companies like Patton are going to eat 3COM's lunch in the small/mid sized >ISP arena.... > >Since support is sold per card (and you gotta cover all the cards!) quick >add up and see what 3COM is gonna cost you to go v.92. > >Then look at all the OTHER RAS vendors that are doing FREE v.92 >upgrades.... > >Paul Farber >Farber Technology >farber(a)admin.f-tech.net >Ph 570-628-5303 >Fax 570-628-5545 > >On Thu, 5 Apr 2001, Marshall Morgan wrote: > >> Who actually has a service contract except ANS/AOL and such? In addition, >> it also says nothing about supporting v.92 on anything but Enhanced chassis' >> (DS3 Ingress/Quad DS1 DSPs, 128M HiperNMCs and newer HiperARCs (256M and >> faster processers?) - not necessarily single T1/E1 HiperDSPs, or 16M >> HiperNMCs or 64/128M HiperARCs. >> >> Overall 3Com/Commworks will find a way to try and get money out of us - who >> is purchasing near the quantity of modems that they did two years ago. Only >> time will tell - (I mean, when did they ever meet a code update date in the >> past?) >> >> Marshall Morgan >> >> Internet Doorway, Inc (aka NETDOOR) >> http://www.netdoor.com >> >> 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 >> ----- Original Message ----- >> From: "Mark E. Levy" <Mark(a)fsi.net> >> To: <usr-tc(a)lists.xmission.com> >> Sent: Thursday, April 05, 2001 10:04 PM >> Subject: RE: (usr-tc) Commworks v.92 Announcement >> >> >> > It's my understanding that it will be free - if you have a service >> > contract... >> > >> > > Of course it will be free! .... yeah right :-} >> > > >> > > Marshall Morgan >> > > >> > > Internet Doorway, Inc (aka NETDOOR) >> > > http://www.netdoor.com >> > > >> > > 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax >> > > 601.969.3838 >> > > ----- Original Message ----- >> > > From: "Mike Andrews" <mandrews(a)bit0.com> >> > > To: <usr-tc(a)lists.xmission.com> >> > > Sent: Thursday, April 05, 2001 6:09 PM >> > > Subject: Re: (usr-tc) Commworks v.92 Announcement >> > > >> > > >> > > > Hm. Q3 of 2001. No word on pricing. >> > > > >> > > > >> > > > Mike Andrews * mandrews(a)dcr.net * mandrews(a)bit0.com * >> > http://www.bit0.com >> > > VP, sysadmin, & network guy, Digital Crescent Inc, Frankfort KY >> > > Internet access for Frankfort, Lexington, Louisville and surrounding >> > counties >> > > www.fark.com: If it's not news, it's Fark. (Or something like that.) >> > > >> > > On Thu, 5 Apr 2001, Marshall Morgan wrote: >> > > >> > > > http://commworks.com/svprovider/news/apr0401b.html >> > > > >> > > > "COMMWORKS CORPORATION TO SUPPORT V.92 MODEM STANDARD ON ITS FLAGSHIP >> > TOTAL >> > > > CONTROL 1000 ENHANCED DATA SYSTEM" >> > > >> > > >> > > - >> > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" >> > > with "unsubscribe usr-tc" in the body of the message. >> > > For information on digests or retrieving files and old messages send >> > > "help" to the same address. Do not use quotes in your message. >> > > >> > > >> > >> > >> > - >> > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" >> > with "unsubscribe usr-tc" in the body of the message. >> > For information on digests or retrieving files and old messages send >> > "help" to the same address. Do not use quotes in your message. >> > >> > - >> > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" >> > with "unsubscribe usr-tc" in the body of the message. >> > For information on digests or retrieving files and old messages send >> > "help" to the same address. Do not use quotes in your message. >> > >> > >> >> >> - >> To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" >> with "unsubscribe usr-tc" in the body of the message. >> For information on digests or retrieving files and old messages send >> "help" to the same address. Do not use quotes in your message. >> > > >- > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

3 2

RE: (usr-tc) Commworks v.92 Announcement
by Mark E. Levy 06 Apr '01

06 Apr '01

Who has a service contract? I do. And it's also my understanding that the V.92 code runs on the 24-port HiperDSP. It's got nothing to do with the ARC. Mark Levy > -----Original Message----- > From: Marshall Morgan [mailto:marshall@netdoor.com] > Sent: Thursday, April 05, 2001 11:37 PM > To: usr-tc(a)lists.xmission.com > Subject: Re: (usr-tc) Commworks v.92 Announcement > > > Who actually has a service contract except ANS/AOL and such? > In addition, > it also says nothing about supporting v.92 on anything but > Enhanced chassis' > (DS3 Ingress/Quad DS1 DSPs, 128M HiperNMCs and newer > HiperARCs (256M and > faster processers?) - not necessarily single T1/E1 HiperDSPs, or 16M > HiperNMCs or 64/128M HiperARCs. > > Overall 3Com/Commworks will find a way to try and get money > out of us - who > is purchasing near the quantity of modems that they did two > years ago. Only > time will tell - (I mean, when did they ever meet a code > update date in the > past?) > > Marshall Morgan > > Internet Doorway, Inc (aka NETDOOR) > http://www.netdoor.com > > 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax > 601.969.3838 > ----- Original Message ----- > From: "Mark E. Levy" <Mark(a)fsi.net> > To: <usr-tc(a)lists.xmission.com> > Sent: Thursday, April 05, 2001 10:04 PM > Subject: RE: (usr-tc) Commworks v.92 Announcement > > > > It's my understanding that it will be free - if you have a service > > contract... > > > > > Of course it will be free! .... yeah right :-} > > > > > > Marshall Morgan > > > > > > Internet Doorway, Inc (aka NETDOOR) > > > http://www.netdoor.com > > > > > > 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax > > > 601.969.3838 > > > ----- Original Message ----- > > > From: "Mike Andrews" <mandrews(a)bit0.com> > > > To: <usr-tc(a)lists.xmission.com> > > > Sent: Thursday, April 05, 2001 6:09 PM > > > Subject: Re: (usr-tc) Commworks v.92 Announcement > > > > > > > > > > Hm. Q3 of 2001. No word on pricing. > > > > > > > > > > > > Mike Andrews * mandrews(a)dcr.net * mandrews(a)bit0.com * > > http://www.bit0.com > > > VP, sysadmin, & network guy, Digital Crescent Inc, Frankfort KY > > > Internet access for Frankfort, Lexington, Louisville and > surrounding > > counties > > > www.fark.com: If it's not news, it's Fark. (Or something > like that.) > > > > > > On Thu, 5 Apr 2001, Marshall Morgan wrote: > > > > > > > http://commworks.com/svprovider/news/apr0401b.html > > > > > > > > "COMMWORKS CORPORATION TO SUPPORT V.92 MODEM STANDARD > ON ITS FLAGSHIP > > TOTAL > > > > CONTROL 1000 ENHANCED DATA SYSTEM" > > > > > > > > > - > > > To unsubscribe to usr-tc, send an email to > "majordomo(a)xmission.com" > > > with "unsubscribe usr-tc" in the body of the message. > > > For information on digests or retrieving files and old > messages send > > > "help" to the same address. Do not use quotes in your message. > > > > > > > > > > > > - > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > with "unsubscribe usr-tc" in the body of the message. > > For information on digests or retrieving files and old > messages send > > "help" to the same address. Do not use quotes in your message. > > > > - > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > with "unsubscribe usr-tc" in the body of the message. > > For information on digests or retrieving files and old > messages send > > "help" to the same address. Do not use quotes in your message. > > > > > > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Commworks v.92 Announcement
by Marshall Morgan 06 Apr '01

06 Apr '01

http://commworks.com/svprovider/news/apr0401b.html "COMMWORKS CORPORATION TO SUPPORT V.92 MODEM STANDARD ON ITS FLAGSHIP TOTAL CONTROL 1000 ENHANCED DATA SYSTEM" Marshall Morgan Internet Doorway, Inc (aka NETDOOR) http://www.netdoor.com 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 2

(usr-tc) CT1 code
by Patrick C. Wolf 04 Apr '01

04 Apr '01

I just recently purchased a used TC with a dual CT1/PRI NIC/NAC pair, 12 Quad modem cards, netserver and NMC. The problem is that the CT1/PRI card is flashed for PRI and I need CT1. Anybody have the CT1 code "laying around" that you can e-mail to me? Or anybody have a dual CT1/PRI card that is already flashed and you're willing to part with it? Thanks in advance. Pat - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Axcell DSL cards
by Timothy C. Bohen 04 Apr '01

04 Apr '01

Does anyone know the scoop on the Axcell (sp) DSL cards for the Total Control Chassis? I have a chance to buy some cheap and wanted to know if they were any good. What would I use for a CPE modem? Thanks Timothy C. Bohen CMSInter.Net / Crystal MicroSystems ============================ web : www.cmsinter.net email : Tim(a)CMSInter.Net phone : 517.235.5100 x22 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

3 2

Fw: Re: (usr-tc) Minimum Power Supply requirements?
by Marshall Morgan 03 Apr '01

03 Apr '01

>From 06/1999 list. Marshall Morgan Internet Doorway, Inc (aka NETDOOR) http://www.netdoor.com 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 ----- Original Message ----- From: "Tatai SV Krishnan" <tkrishna(a)bubba.ae.usr.com> To: "matthews" <matthews(a)staff.brunnet.net> Cc: <usr-tc(a)lists.xmission.com> Sent: Thursday, June 03, 1999 3:13 PM Subject: RE: (usr-tc) Maximum cards per chassis (WAS RE: Quad modem NIC's. ..take up power??) > On Thu, 3 Jun 1999, matthews wrote: > > > > > Do you plan to be able to support the same numbers when 4.2.x comes out? > > As far as I know yes, > > krish > > > > > > On Thursday, June 03, 1999 3:30 PM, Tatai SV Krishnan [SMTP:tkrishna@bubba.ae.usr.com] wrote: > > > On Thu, 3 Jun 1999, matthews wrote: > > > > > > > > > > > Didn't Krish say that the ARC has been lab tested and been able to handle > > > > 14 DSPs or am I losing my mind? If not, exactly how many DSPs can 1 ARC > > > > handle? > > > > > > Hiper arc 4.1.x code supports 14 Hiper dsps - This configuration is only > > > valid if you are using IP. If you are using IPX and IP only 7 DSP per > > > hiper arc is supported. If you are using IPX only - again only 7 DSP per > > > hiper arc is supported. > > > > > > > > > > > > > > On Thursday, May 27, 1999 1:52 PM, Florin_Neamtu(a)3com.com > > > > [SMTP:Florin_Neamtu@3com.com] wrote: > > > > > > > > > > > > > > > Backplane consumption: 7.8 W 26.6 BTUs > > > > > > > > > > > > > > > > > > > > > > > > > POWER AND HiPer CARD SUPPORT CONSIDERATIONS > > > > > > > > > > The following table provides the maximum number of cards in both HiPer > > > > > Access Router and NetServer configurations supported in associated > > > > chassis. > > > > > This table assumes T1 configurations, with each HiPer DSP card supporting > > > > > 24 calls. > > > > > |-------------------+--------------+------------------------> > > > > > | | | | > > > > > | | Double-Up | Maximum Number of | > > > > > | Chassis | Supported? | HiPer DSP + HiPer ARC | > > > > > | | | (1) | > > > > > | | | | > > > > > |-------------------+--------------+------------------------> > > > > > >-----------------------| > > > > > | | > > > > > | Maximum Number of | > > > > > | HiPer DSP + NetServer | > > > > > | (2) | > > > > > | | > > > > > >-----------------------| > > > > > |-------------------+--------------+------------------------> > > > > > | | | | > > > > > | 45Amp | Yes | 6 + 1 (144 calls) | > > > > > | | | 6 HiPer DSP cards and | > > > > > | | | 1 HiPer Access Router | > > > > > | | | card | > > > > > | | | | > > > > > |-------------------+--------------+------------------------> > > > > > >-----------------------| > > > > > | | > > > > > | 1 x (4 + 1) (96 | > > > > > | calls) | > > > > > | 1 set of 4 HiPer DSP | > > > > > | cards with 1 | > > > > > | NetServer | > > > > > | | > > > > > >-----------------------| > > > > > |-------------------+--------------+------------------------> > > > > > | | | | > > > > > | 70Amp | Yes | 10 + 2 (240 calls) | > > > > > | | | 10 HiPer DSP cards and | > > > > > | | | 2 HiPer Access Router | > > > > > | | | cards | > > > > > | | | | > > > > > |-------------------+--------------+------------------------> > > > > > >-----------------------| > > > > > | | > > > > > | 2 x (4 + 1) (192 | > > > > > | calls) | > > > > > | 2 sets of 4 HiPer DSP | > > > > > | cards with 1 | > > > > > | NetServer | > > > > > | | > > > > > >-----------------------| > > > > > |-------------------+--------------+------------------------> > > > > > | | | | > > > > > | 130Amp | Yes | 14 + 2 (336 calls) | > > > > > | | | 14 HiPer DSP cards and | > > > > > | | | 2 HiPer Access Router | > > > > > | | | cards | > > > > > | | | | > > > > > |-------------------+--------------+------------------------> > > > > > >-----------------------| > > > > > | | > > > > > | 3 x (4 + 1) (288 | > > > > > | calls) | > > > > > | 3 sets of 4 HiPer DSP | > > > > > | cards with 1 | > > > > > | NetServer | > > > > > | | > > > > > >-----------------------| > > > > > > > > > > > > > > > > > > > > Notes: > > > > > (1) Figures shown in this column represent the maximum number of HiPer > > > > DSP > > > > > cards and HiPer Access Router cards which can be supported in the > > > > > associated chassis. Thus, the entry > > > > > > > > > > > > > > > > During the first release of hiper arc, the hiper arc could handle only 7 > > > DSP for IP ( 4.0.X) code. This information may be in that regards. > > > > > > Also the TCS 3.5 code supports DSA and ILB - thus having a fall-over > > > hiper arc is suggested. > > > > > > > > > Hope this helps > > > > > > krish > > > > > > > > > > > > > > > > ?6 + 1? refers to 6 HiPer DSP card > > > > > sets plus 1 HiPer Access Router set (10/100M ethernet) supporting a > > > > > corresponding 144 calls. > > > > > (2) Figures shown in this column represent the maximum number of HiPer > > > > DSP > > > > > cards and NetServer cards which can be supported in the associated > > > > > chassis. With the NetServer card upgraded to TCS3.0 (associated > > > > NetServer > > > > > card release 3.6.x) and supporting up to 96 calls, the NetServer card > > > > is > > > > > thus able to support 4 HiPer DSP cards, assuming T1 configurations (24 > > > > > channels per HiPer DSP card set). Thus, the entry ?1 x (4 + 1)? refers > > > > to > > > > > 1 set (1 x) of 4 HiPer DSP cards plus 1 NetServer card (supporting 96 > > > > > calls) for a system capability of 96 calls. > > > > > > > > > > When Do Customers Need to go to the 130Amp Supplies > > > > > Customers will need to swap out their existing 70Amp PSU/PSI set(s) and > > > > > install 130Amp PSU/PSI set(s) once they exceed 10 HiPer DSP cards in the > > > > 10 > > > > > HiPer DSP + 2 HiPer Access Router configuration or once they exceed the 2 > > > > > sets of the 4 HiPer DSP + 1 NetServer card configuration. The 70Amp power > > > > > supplies PSU/PSI sets can be exchanged for the 130Amp PSU/PSI sets. > > > > > However, the 45Amp supplies cannot be upgraded to either 70Amp or 130Amp > > > > > supplies. > > > > > > > > > > > > > > > > > > > > > > > > > The information I have goes like this; > > > > > > > > > > Pwr supply Max calls hiper Arc /hdm max calls > > > > > HDM/netserver > > > > > > > > > > 45Amp 6 HDM + 1 Harc = 144/180 calls 4 HDM + 1 > > > > > Netserver =96/120 calls > > > > > > > > > > 70Amp 10 HDM + 2 Harc = 230/300 calls 8 HDM + 2 > > > > > Netservers =192/240 calls > > > > > > > > > > 130Amp 14 HDM + 2 Harc = 336/420 calls 12 HDM + 3 > > > > > Netservers = 288/360 calls > > > > > > > > > > Hope this helps > > > > > Florin N > > > > > > > > > > > > > > > > > > > > > > > > > - > > > > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > > > > with "unsubscribe usr-tc" in the body of the message. > > > > > For information on digests or retrieving files and old messages send > > > > > "help" to the same address. Do not use quotes in your message. > > > > > > > > > > > > > > > > > > > > - > > > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > > > with "unsubscribe usr-tc" in the body of the message. > > > > For information on digests or retrieving files and old messages send > > > > "help" to the same address. Do not use quotes in your message. > > > > > > > > > > - > > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > > with "unsubscribe usr-tc" in the body of the message. > > > For information on digests or retrieving files and old messages send > > > "help" to the same address. Do not use quotes in your message. > > > > > > > > > > - > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > with "unsubscribe usr-tc" in the body of the message. > > For information on digests or retrieving files and old messages send > > "help" to the same address. Do not use quotes in your message. > > > > - > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. > > - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Minimum Power Supply requirements?
by Mark Thornton 02 Apr '01

02 Apr '01

What is the minimum power supply requirements for a loaded dsp chassis, say 10 dsp's and 2 arc's? What is required to have redundancy within the chassis? At what number of cards does a dual 70 amp chassis not provide redundancy if this is a problem? Another related question, how many dsp's can be handled by an arc? With the new multi trunk dsp's the limit must be fairly high. Is there a realistic need for more than one in a chassis containing only single trunk dsp's? Mark Thornton San Marcos Internet, Inc. 512-393-5300 - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

2 2