April 2000 - USR-TC - mailman.xmission.com

(usr-tc) Modems not answering on Dual PRI card
by Eric Forcey 06 Apr '00

06 Apr '00

Hello all, I've got a perplexing problem with a dual-pri card feeding into quads. The circuit is set up good signal. Telco shows that they are handing calls to the PRI but they are being refused by my chassis. Line interface is set to pritdm, all ds0's show in service. Dunno where else to check... any ideas? -Eric - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

3 2

(usr-tc) Total Control Netserver - loopstart trunk type and immediate trunk signal start not sticking
by Jeremy Malli 06 Apr '00

06 Apr '00

I'm hoping somebody has an solution for this; I have a USR TC Netserver, running the latest firmware on all the cards that will not allow me to use loopstart and immediate signaling at the same time. I can change the options in TCM, but after I click Set, and then OK, then save the card to NVRAM and reboot, it has magically changed the configs for the trunk signal start back to dialTone. It will keep the loopstart setting, but no matter what trunk signaling type I set it to, it will always revert back to dialtone. Anybody know how to make the immediate start stick? Jeremy Malli - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

4 5

(usr-tc) ISDN Point-to-Point
by Boa Vida 06 Apr '00

06 Apr '00

Sorry if it is a little off-topic. Can I use two Courier-I modems to make a point-to-point connection? If it is possible, the connection will be at 128k (using both B channels) or it'll be a 56k analog connection? Has any one already used it through a leased-line? Thanks for any help. ____________________________________________________________________ Get your own FREE, personal Netscape WebMail account today at http://webmail.netscape.com. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) Anybody use a MAX 6048?
by Scot Desort 06 Apr '00

06 Apr '00

We are looking to add alternative equipment to compliment our 3COM TC gear. We are looking at the Max 6048. Anybody use these boxes? Any opinion, good or bad, about their performance, features, compatibility, etc? I know some folks here use TNT's, but they're just not in our budget. -- Scot - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

Re: (usr-tc) x2/v90 enable on 16MB NMC
by Greg Coffey 06 Apr '00

06 Apr '00

If the old one had the x2 key enabled, you need to call 3Com and they can transfer it to the new card. We've had to do it a couple of times. At 10:14 AM 4/6/00 -0500, you wrote: >On Thu, 6 Apr 2000, Kalev Nurklik wrote: > > > OK, got a little problem here. > > Had a chassis with old 4MB NMC that got replaced with 16NMC > > chassis (not Hiper NMC). Some of the quads remained on the > > chassis so as a sum result I lost v90 support on these cards. > > I must confess that I know little about 3com policy about added > > cost features - having been involved mainly with HDSPs till now. > > Can somebody bring me up to date with that? > > 1. What must be done to enable v90 on quads with 16MB NMC? > > or > >A feature enable key must be entered into the NMC. > > > 2. Where can I get 16MB NMC feature key to enable v90 if this > > is as that simple? > >You can pay a few thousand dollars to 3Com, then they will gladly give >you v.90 on your quads. > >Brian > > > > > > Regards, > > __________________________________ > > Kalev Nurklik > > Delfi Online > > Pa"rnu mnt. 158, 11317 Tallinn, Estonia > > Tel: +372 6501709 > > Fax: +372 6501708 > > E-mail: k.nurklik(a)delfi.ee > > http://online.delfi.ee > > > > - > > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > > with "unsubscribe usr-tc" in the body of the message. > > For information on digests or retrieving files and old messages send > > "help" to the same address. Do not use quotes in your message. > > > >----------------------------------------------------- >Brian Feeny (BF304) signal(a)shreve.net >318-222-2638 x 109 http://www.shreve.net/~signal >Network Administrator ShreveNet Inc. (ASN 11881) > > >- > To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" > with "unsubscribe usr-tc" in the body of the message. > For information on digests or retrieving files and old messages send > "help" to the same address. Do not use quotes in your message. Thanks, Greg Coffey <gcoffey(a)vcn.com> Visionary Communications V 307-234-5443 F 307-234-5446 100 N. Center Suite #100, Casper, WY 82601 www.vcn.com _________________________________________________________ - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) x2/v90 enable on 16MB NMC
by Kalev Nurklik 06 Apr '00

06 Apr '00

OK, got a little problem here. Had a chassis with old 4MB NMC that got replaced with 16NMC chassis (not Hiper NMC). Some of the quads remained on the chassis so as a sum result I lost v90 support on these cards. I must confess that I know little about 3com policy about added cost features - having been involved mainly with HDSPs till now. Can somebody bring me up to date with that? 1. What must be done to enable v90 on quads with 16MB NMC? or 2. Where can I get 16MB NMC feature key to enable v90 if this is as that simple? Regards, __________________________________ Kalev Nurklik Delfi Online Pa"rnu mnt. 158, 11317 Tallinn, Estonia Tel: +372 6501709 Fax: +372 6501708 E-mail: k.nurklik(a)delfi.ee http://online.delfi.ee - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

4 3

(usr-tc) FS: USR TC v90
by Steve Rivera 06 Apr '00

06 Apr '00

In Stock, Tested thru TCM. All Modems flash v90 NMC v90 enabled. Can configure chassis's to your specifications. (digital, analog/digital) USR Technician available for hire. install assistance, configuration at your ip address. Quad Digital Bundles include: $4500 or BO Chassis with Dual 45A power Netserver PRI NMC v90 12- Digital Modems Dual PRI Quad Analog/Digital Bundles include: $6000 or BO HD Chassis with integrated fan tray, single 70A power nmc v90 enabled hiper arc 12- Quad analog/digital modems dual pri WTB: Hiper DSP's!!! .................................................... Worldwide Provider of Network Hardware Since 1981. Steve Rivera - v-732-833-2111 / 732-433-5890 24Hr Email Page 7324335890(a)page.nextel.com http://www.ISP-NetworkHardware.com or http://www.wrca.net Cisco, Ascend, Livingston, USR, Microcom, Motorola Computone, Kentrox, Adtran...and more - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

8 16

RE: (usr-tc) WTB: 2- Hiper DSP Immediately
by Mike Storjohann 04 Apr '00

04 Apr '00

I am also looking for 2 HiperDSP sets. Please let me know off list if any of you have some for sale. Thank you. Mike Storjohann Internet Services Administrator HunTel.net mstorjohann(a)huntel.net 402-426-6136 -----Original Message----- From: owner-usr-tc(a)lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of Steve Rivera Sent: Tuesday, April 04, 2000 2:06 PM To: usr-tc(a)lists.xmission.com Subject: (usr-tc) WTB: 2- Hiper DSP Immediately Subject says it all. Buying Today! Please email or call me with what you may have available. .................................................... Worldwide Provider of Network Hardware Since 1981. Steve Rivera - v-732-833-2111 / 732-433-5890 24Hr Email Page 7324335890(a)page.nextel.com (start message with YOUR email address) http://www.ISP-NetworkHardware.com or http://www.wrca.net Cisco, Ascend, Livingston, USR, Microcom, Motorola Computone, Kentrox, Adtran...and more - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) WTB: 2- Hiper DSP Immediately
by Steve Rivera 04 Apr '00

04 Apr '00

Subject says it all. Buying Today! Please email or call me with what you may have available. .................................................... Worldwide Provider of Network Hardware Since 1981. Steve Rivera - v-732-833-2111 / 732-433-5890 24Hr Email Page 7324335890(a)page.nextel.com (start message with YOUR email address) http://www.ISP-NetworkHardware.com or http://www.wrca.net Cisco, Ascend, Livingston, USR, Microcom, Motorola Computone, Kentrox, Adtran...and more - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

1 0

(usr-tc) OSPF docs
by Scott Doty 04 Apr '00

04 Apr '00

Hi, Our new firmware supports OSPF. However, I'll be darned if I can find any documentation for it. Does someone know where I can find TC OSPF docs, or do I have to fight through the USR support tangle? Thanks, -Scott - To unsubscribe to usr-tc, send an email to "majordomo(a)xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

3 2