not sure whats going on there but we have the same setup except DSP's instead of quads. never have problems with the 800's. here's my configs - the ppp auth. config on the Cisco is a little wierd but thats the only way I could get auth. requests answered by the ARC. Hope this helps!!!!!! Current configuration: ! version 12.0 no service pad service timestamps debug datetime msec localtime show-timezone service timestamps log datetime localtime show-timezone service password-encryption ! hostname xxx ! username xxx password yyy ! ip subnet-zero ! isdn switch-type basic-ni ! interface Ethernet0 ip address 10.0.0.80 255.255.255.0 no ip directed-broadcast ip nat inside no cdp enable ! interface BRI0 no ip address no ip directed-broadcast ip nat outside encapsulation ppp dialer rotary-group 1 isdn switch-type basic-ni isdn spid1 xxxxxxxxxxxxxx xxxxxxx isdn voice-priority xxxxxxx in always isdn incoming-voice modem no cdp enable ! interface Dialer1 description ISP ip address negotiated no ip directed-broadcast no ip proxy-arp ip nat outside encapsulation ppp no ip split-horizon dialer in-band dialer idle-timeout 9000 dialer string xxxxxxx dialer load-threshold 1 either dialer-group 1 no cdp enable ppp authentication pap callin ppp chap password yyy ppp pap sent-username xxx password yyy ppp multilink ! ip nat inside source list 1 interface Dialer1 overload ip http server ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 ! access-list 1 permit 10.0.0.0 0.0.0.255 dialer-list 1 protocol ip permit no cdp run ! line con 0 exec-timeout 0 0 transport input none stopbits 1 line vty 0 4 password yyy login ! end tpk-32.7> sh ppp PPP AUTHENTICATION DIAL_IN Users Authenticate: PAP PPP Authentication Preference: DEFAULT System Transmit Authentication Name: xxxx PPP offloading: DISABLED CCP will be attempted for call type(s): NONE Primary NBNS Server address: 0.0.0.0 Secondary NBNS Server address: 0.0.0.0 DNS configuration Usage: SYSTEM Primary PPP DNS Server address: 0.0.0.0 Secondary PPP DNS Server address: 0.0.0.0 PPP session start message: PPP session from %server_ip to %client _ip beginning.... Send Accounting for PPP Abnormal Disc: DISABLED PPP Address Field Compression: ENABLED PPP Protocol Field Compression: ENABLED PPP Multilink PPP: ENABLED PPP BACP and BAP: DISABLED PPP Bap Hunt Group Phone Number: PPP Receive ACCM: DISABLED

-----Original Message----- From: Laszlo Vecsey [mailto:master@internexus.net] Sent: Friday, January 07, 2000 9:39 PM To: usr-tc@xmission.com Subject: (usr-tc) cisco 804 to total-control hiperarc

I have a customer attempting to dial up with an isdn cisco 804 unit, to a total control hiperarc (quad modems). The connection is established and I see the authentication show up in the radius server log, but then the connection gets dropped. The user and pass is accepted ok.

I monitored the ppp call events on the hiperarc, and as the call comes in it says almost instantly that the Peer does not have any IP protocol set, so DISABLING. Any idea why that might be?

- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.

- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.