(usr-tc) Quad Analog Modem Problems
Hi, I am having problems with some Quad Analog modem cards that I have installed, I cannot get them to stay active I do set modem s49 active and it all appears to work, then I save and reset then I get whats below. the modems report A/I/P then after a reset they go A/A/P but I cant get them A/R/P. Basically the modem is not active because it cannot successfully negociate with the packet bus(I think). after a reset my syslog reports: Apr 28 14:05:19 dialup9.dataheart.net S49 packet bus handle opened. Handle = 26. After this the netserver reports the modem as active all though there is still no HDLC Framing and the interface is still set to Unassigned instead of ptp49 as it usually is. then 30 seconds later: Apr 28 14:05:49 dialup9.dataheart.net S49 packet bus failed to connect! stat=-1 Apr 28 14:05:49 dialup9.dataheart.net S49 packet bus handle closed. now the netserver reports it as inactive again. I have Quad Digital/Analog cards working fine in the same chassis but these Quad Analogs are just not co-operating. any help would be appreciated, the 3com knowledgebase has not helped me. Thanks, Aaron Daniels - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Hello Aaron, Sunday, April 29, 2001, 7:12:02 PM, you wrote: Did you ever find a soulution to this problem if so what was it??? AD> Hi, AD> I am having problems with some Quad Analog modem cards that I have installed, AD> I cannot get them to stay active I do set modem s49 active and it all appears to work, then I save AD> and reset then I get whats below. AD> the modems report A/I/P then after a reset they go A/A/P but I cant get them A/R/P. AD> Basically the modem is not active because it cannot successfully negociate with the packet bus(I AD> think). AD> after a reset my syslog reports: AD> Apr 28 14:05:19 dialup9.dataheart.net S49 packet bus handle opened. Handle = 26. AD> After this the netserver reports the modem as active all though there is still no HDLC Framing and AD> the interface is still set to Unassigned instead of ptp49 as it usually is. AD> then 30 seconds later: AD> Apr 28 14:05:49 dialup9.dataheart.net S49 packet bus failed to connect! stat=-1 AD> Apr 28 14:05:49 dialup9.dataheart.net S49 packet bus handle closed. AD> now the netserver reports it as inactive again. AD> I have Quad Digital/Analog cards working fine in the same chassis but these Quad Analogs are just AD> not co-operating. AD> any help would be appreciated, AD> the 3com knowledgebase has not helped me. AD> Thanks, AD> Aaron Daniels AD> - AD> To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" AD> with "unsubscribe usr-tc" in the body of the message. AD> For information on digests or retrieving files and old messages send AD> "help" to the same address. Do not use quotes in your message. -- Thanks, Craig Craig@tavrida.net - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
After setting set modem s49 active, do a hardware reset to modem card from TCM. ----- Original Message ----- From: "Craig" <Craig@tavrida.net> To: "Aaron Daniels" <usr-tc@lists.xmission.com> Sent: Friday, June 29, 2001 11:06 AM Subject: Re: (usr-tc) Quad Analog Modem Problems
Hello Aaron,
Sunday, April 29, 2001, 7:12:02 PM, you wrote:
Did you ever find a soulution to this problem if so what was it??? AD> Hi, AD> I am having problems with some Quad Analog modem cards that I have installed, AD> I cannot get them to stay active I do set modem s49 active and it all appears to work, then I save AD> and reset then I get whats below. AD> the modems report A/I/P then after a reset they go A/A/P but I cant get them A/R/P.
AD> Basically the modem is not active because it cannot successfully negociate with the packet bus(I AD> think). AD> after a reset my syslog reports: AD> Apr 28 14:05:19 dialup9.dataheart.net S49 packet bus handle opened. Handle = 26.
AD> After this the netserver reports the modem as active all though there is still no HDLC Framing and AD> the interface is still set to Unassigned instead of ptp49 as it usually is. AD> then 30 seconds later: AD> Apr 28 14:05:49 dialup9.dataheart.net S49 packet bus failed to connect! stat=-1 AD> Apr 28 14:05:49 dialup9.dataheart.net S49 packet bus handle closed.
AD> now the netserver reports it as inactive again.
AD> I have Quad Digital/Analog cards working fine in the same chassis but these Quad Analogs are just AD> not co-operating.
AD> any help would be appreciated, AD> the 3com knowledgebase has not helped me. AD> Thanks, AD> Aaron Daniels
AD> - AD> To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" AD> with "unsubscribe usr-tc" in the body of the message. AD> For information on digests or retrieving files and old messages send AD> "help" to the same address. Do not use quotes in your message.
-- Thanks, Craig Craig@tavrida.net
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Hello Nauman, Saturday, June 30, 2001, 1:08:42 AM, you wrote: Hello We have done that and they will answer using the rs232 cable but not the analog rj's when running info on the mode it says dte rs232 and when we check s13 it set to s13=32 which is to force use gateway.... It seems that is the proble now it getting the modem to use the gateway my tech belive. could you send me a complete terminal print out of your setting of one of your analog modem for we can compare!! Craig NM> After setting set modem s49 active, do a hardware reset to modem card from NM> TCM. NM> ----- Original Message ----- NM> From: "Craig" <Craig@tavrida.net> NM> To: "Aaron Daniels" <usr-tc@lists.xmission.com> NM> Sent: Friday, June 29, 2001 11:06 AM NM> Subject: Re: (usr-tc) Quad Analog Modem Problems
Hello Aaron,
Sunday, April 29, 2001, 7:12:02 PM, you wrote:
Did you ever find a soulution to this problem if so what was it??? AD> Hi, AD> I am having problems with some Quad Analog modem cards that I have NM> installed, AD> I cannot get them to stay active I do set modem s49 active and it all NM> appears to work, then I save AD> and reset then I get whats below. AD> the modems report A/I/P then after a reset they go A/A/P but I cant NM> get them A/R/P.
AD> Basically the modem is not active because it cannot successfully NM> negociate with the packet bus(I AD> think). AD> after a reset my syslog reports: AD> Apr 28 14:05:19 dialup9.dataheart.net S49 packet bus handle opened. NM> Handle = 26.
AD> After this the netserver reports the modem as active all though there NM> is still no HDLC Framing and AD> the interface is still set to Unassigned instead of ptp49 as it NM> usually is. AD> then 30 seconds later: AD> Apr 28 14:05:49 dialup9.dataheart.net S49 packet bus failed to NM> connect! stat=-1 AD> Apr 28 14:05:49 dialup9.dataheart.net S49 packet bus handle closed.
AD> now the netserver reports it as inactive again.
AD> I have Quad Digital/Analog cards working fine in the same chassis but NM> these Quad Analogs are just AD> not co-operating.
AD> any help would be appreciated, AD> the 3com knowledgebase has not helped me. AD> Thanks, AD> Aaron Daniels
AD> - AD> To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" AD> with "unsubscribe usr-tc" in the body of the message. AD> For information on digests or retrieving files and old messages send AD> "help" to the same address. Do not use quotes in your message.
-- Thanks, Craig Craig@tavrida.net
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
NM> - NM> To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" NM> with "unsubscribe usr-tc" in the body of the message. NM> For information on digests or retrieving files and old messages send NM> "help" to the same address. Do not use quotes in your message. -- Thanks, Craig Craig@tavrida.net - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
participants (3)
-
Aaron Daniels -
Craig -
Nauman Malik