RE: [USR-TC] firmware/flash on usr total control
Hi Jason, There is no 5.4.1 code for the NetServer cards. The last version of code was 3.8.1 or 3.7.24 and there were no further code revisions after that. The NetServer was End-of-Lifed by CommWorks at least 2-3 years ago and they stopped producing code before that. Here is a link to the Software Matrix that you can check and verify your code version..... http://totalservice.commworks.com/Matrixs/TCSMatrix.cfm Thanks, Steve Solunet TAC -----Original Message----- From: Jason Branscum [mailto:jasonb@gower.net] Sent: Monday, May 13, 2002 5:35 PM To: usr-tc@lists.xmission.com Subject: [USR-TC] firmware/flash on usr total control hello, I have a usr total control box with the old Netserver cards. I was wondering if there is a upgrade/update for it. I'm running version 5.4.1 I think. Is their any upgrading I can do? Jason Jason M Branscum Network Admin Gower Computer Support / Gower.net 903-597-9220 Political T.V. commercials prove one thing: some candidates can tell all their good points and qualifications in just 30 seconds. _______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
Actually, I have 3.8.67 which is a beta release, I have it because we had a reboot issue which turned to be an hardware problem. I've been running it in production for years without problem. -Martin; B2B2C.ca ----- Original Message ----- From: <SWujek@solunet.com> To: <usr-tc@mailman.xmission.com>; <usr-tc@lists.xmission.com> Sent: Tuesday, May 14, 2002 10:17 AM Subject: RE: [USR-TC] firmware/flash on usr total control
Hi Jason, There is no 5.4.1 code for the NetServer cards. The last version of code was 3.8.1 or 3.7.24 and there were no further code revisions after that. The NetServer was End-of-Lifed by CommWorks at least 2-3 years ago and they stopped producing code before that. Here is a link to the Software Matrix that you can check and verify your code version..... http://totalservice.commworks.com/Matrixs/TCSMatrix.cfm
Thanks, Steve Solunet TAC
-----Original Message----- From: Jason Branscum [mailto:jasonb@gower.net] Sent: Monday, May 13, 2002 5:35 PM To: usr-tc@lists.xmission.com Subject: [USR-TC] firmware/flash on usr total control
hello,
I have a usr total control box with the old Netserver cards. I was wondering if there is a upgrade/update for it. I'm running version 5.4.1 I think. Is their any upgrading I can do?
Jason Jason M Branscum Network Admin Gower Computer Support / Gower.net 903-597-9220
Political T.V. commercials prove one thing: some candidates can tell all their good points and qualifications in just 30 seconds.
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
Recently I moved the last old quad modems I have off the netserver to a hiperArc. The chassis was running a single DSP just fine. Once I added the Quads I now a hiperArc that locks up every couple days. The quads are running analog pots lines so they have the nics installed. I have run many quads in chassis with the hiperarcs, just not in analog mode with pots lines. All the other have the t1 cards. Any one out there have this setup and have it running alright? Or is this just to glommed together that it's never going to work. I need the analog lines because where I live some people just can't get connected to the digital lines. quad code 6.0.6 dsp code 2.1.9 hiperArc code 4.2.32 Nmc code 7.1.28 Terry Kennedy
participants (3)
-
Martin Lathoud -
SWujek＠solunet.com -
Terry Kennedy