Can someone tell me the TCM version or software version for v92 compatible code
Customer looking to verify that they have the right code installed. I am not sure when the v92 compatible revisions started Please advise if you can... Hiper DSP Hiper ARC Hiper NMC Thanks in advance.... By the way... oodles of Hiper ARC's and Hiper DSP's available, couple hiper nmc's Steve Rivera IM: srivera711 Toll Free: (877)WRCANET x102 DIRECT: 732-833-2034 Fax available equipment to: (732)833-2115 for more product info got www.wrca.net
On Thursday 20 June 2002 12:46 pm, Stephen Rivera - WRCA.Net wrote:
Customer looking to verify that they have the right code installed. I am not sure when the v92 compatible revisions started
Please advise if you can... Hiper DSP 3.5.12 was the buggy first 3.5.100 is what you want Hiper ARC 5.3.2 Hiper NMC 8.6.3 -- Lewis Bergman Texas Communications 4309 Maple St. Abilene, TX 79602-8044 915-695-6962 ext 115
At 12:53 PM 6/20/2002 -0500, you wrote:
On Thursday 20 June 2002 12:46 pm, Stephen Rivera - WRCA.Net wrote:
Customer looking to verify that they have the right code installed. I am not sure when the v92 compatible revisions started
Please advise if you can... Hiper DSP 3.5.12 was the buggy first 3.5.100 is what you want Hiper ARC 5.3.2 Hiper NMC 8.6.3 -- Lewis Bergman Texas Communications 4309 Maple St. Abilene, TX 79602-8044 915-695-6962 ext 115
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
Steve Rivera IM: srivera711 Toll Free: (877)WRCANET x102 DIRECT: 732-833-2034 Fax available equipment to: (732)833-2115 for more product info got www.wrca.net
Hello everyone, Curious if anyone has seen or is familar with this problem: It appears that by inserting specific DSP's into a chassis (DSP's that we believe are messed up at this point) it causes 1 of our hiperarcs to reboot. It goes into a crash dump sequence. This chassis is doubled up but only 1 of the arc's reboots. If we replace the DSP's the arc comes up and works fine. This tidbit was of course figured out after replacing arc and chassis. Anyone see anything like this before and have any other points of interest? Todd
code versions??? Marshall Morgan Internet Doorway, Inc (aka NETDOOR) http://www.netdoor.com 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 ----- Original Message ----- From: "Todd Bertolozzi" <berto@voyager.net> To: <usr-tc@mailman.xmission.com> Sent: Friday, June 21, 2002 8:44 AM Subject: [USR-TC] Hiper Arc reboots caused by DSP?
Hello everyone,
Curious if anyone has seen or is familar with this problem:
It appears that by inserting specific DSP's into a chassis (DSP's that we believe are messed up at this point) it causes 1 of our hiperarcs to
reboot.
It goes into a crash dump sequence. This chassis is doubled up but only 1 of the arc's reboots. If we replace the DSP's the arc comes up and works fine.
This tidbit was of course figured out after replacing arc and chassis.
Anyone see anything like this before and have any other points of interest?
Todd
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
TCS 3.6?? arc: 4.2.32 dsp: 2.0.60 Hiper NMC: 6.2.17 Todd -----Original Message----- From: usr-tc-admin@mailman.xmission.com [mailto:usr-tc-admin@mailman.xmission.com]On Behalf Of Marshall Morgan Sent: Sunday, June 23, 2002 5:09 AM To: usr-tc@mailman.xmission.com Subject: Re: [USR-TC] Hiper Arc reboots caused by DSP? code versions??? Marshall Morgan Internet Doorway, Inc (aka NETDOOR) http://www.netdoor.com 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 ----- Original Message ----- From: "Todd Bertolozzi" <berto@voyager.net> To: <usr-tc@mailman.xmission.com> Sent: Friday, June 21, 2002 8:44 AM Subject: [USR-TC] Hiper Arc reboots caused by DSP?
Hello everyone,
Curious if anyone has seen or is familar with this problem:
It appears that by inserting specific DSP's into a chassis (DSP's that we believe are messed up at this point) it causes 1 of our hiperarcs to
reboot.
It goes into a crash dump sequence. This chassis is doubled up but only 1 of the arc's reboots. If we replace the DSP's the arc comes up and works fine.
This tidbit was of course figured out after replacing arc and chassis.
Anyone see anything like this before and have any other points of interest?
Todd
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
I would look into upgrading the DSP code first (to something a little newer like 2.1.9 or such). on the ARC, I would ensure I had a simple setup like. NMC SETTINGS Chassis Awareness: DISABLED Dynamic Slot Assignment: DISABLED DSA Idle Rebalancing: ENABLED ... make sure the list chassis reflects the cards (and ports) installed as well and that only one of the ARCs "owns" the DSP. Marshall Morgan Internet Doorway, Inc (aka NETDOOR) http://www.netdoor.com 601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 ----- Original Message ----- From: "Todd Bertolozzi" <berto@voyager.net> To: <usr-tc@mailman.xmission.com> Sent: Tuesday, June 25, 2002 7:52 AM Subject: RE: [USR-TC] Hiper Arc reboots caused by DSP?
TCS 3.6?? arc: 4.2.32 dsp: 2.0.60 Hiper NMC: 6.2.17
Todd
-----Original Message----- From: usr-tc-admin@mailman.xmission.com [mailto:usr-tc-admin@mailman.xmission.com]On Behalf Of Marshall Morgan Sent: Sunday, June 23, 2002 5:09 AM To: usr-tc@mailman.xmission.com Subject: Re: [USR-TC] Hiper Arc reboots caused by DSP?
code versions???
Marshall Morgan
Internet Doorway, Inc (aka NETDOOR) http://www.netdoor.com
601.969.1434 x28 | 800.952.1570 x28 | 601.969.3629 x28 | Fax 601.969.3838 ----- Original Message ----- From: "Todd Bertolozzi" <berto@voyager.net> To: <usr-tc@mailman.xmission.com> Sent: Friday, June 21, 2002 8:44 AM Subject: [USR-TC] Hiper Arc reboots caused by DSP?
Hello everyone,
Curious if anyone has seen or is familar with this problem:
It appears that by inserting specific DSP's into a chassis (DSP's that
we
believe are messed up at this point) it causes 1 of our hiperarcs to reboot. It goes into a crash dump sequence. This chassis is doubled up but only 1 of the arc's reboots. If we replace the DSP's the arc comes up and works fine.
This tidbit was of course figured out after replacing arc and chassis.
Anyone see anything like this before and have any other points of interest?
Todd
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
I'm trying to change the IP address of the NMC card using the TCM. I'm able to get to the Userinterface settings and change the IP address and gateway. I then click on the "set" button, taking away the red coloring from the changed fields. Afterwards I used the TCM command mode to "Save" the changes to the NMC. After resetting the NMC using the command mode, it boots back up with the old/original IP address and original community strings. Making changes and saving to the HiperDSP card worked ok, it's just the NMC I can't save to.
Use "save UI to EEPROM" save the user interface -----Original Message----- From: usr-tc-admin@mailman.xmission.com [mailto:usr-tc-admin@mailman.xmission.com] On Behalf Of Steve Coleman Sent: Wednesday, June 26, 2002 2:08 PM To: usr-tc@mailman.xmission.com Subject: [USR-TC] Saving NMC changes I'm trying to change the IP address of the NMC card using the TCM. I'm able to get to the Userinterface settings and change the IP address and gateway. I then click on the "set" button, taking away the red coloring from the changed fields. Afterwards I used the TCM command mode to "Save" the changes to the NMC. After resetting the NMC using the command mode, it boots back up with the old/original IP address and original community strings. Making changes and saving to the HiperDSP card worked ok, it's just the NMC I can't save to. _______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
I just received a HiperDSP card from an Ebay auction, I noticed the chips were a little different on the NAC... come to find out this is a E1 configured DSP! Is there a way to convert this DSP to T1 mode, or do I need to get rid of this thing and purchase the T1 version. Anybody need an E1 DSP?? :-) - Mike ------------------------------------------------ Rock Island Communications, Inc. (360)-378-5884 http://www.rockisland.com/ San Juan Islands, WA ------------------------------------------------
participants (8)
-
Lewis Bergman -
List -
Marshall Morgan -
Mike Greene -
Stephen Rivera - WRCA.Net -
Steve Coleman -
Terry Kennedy -
Todd Bertolozzi