Re: (usr-tc) HiPerDSP stops at 21
See if you telco capped your inbound available calls... JN ----- Original Message ----- From: "David Swearingin" <david@carolnet.com> To: <usr-tc@lists.xmission.com> Sent: Monday, January 24, 2000 12:00 AM Subject: (usr-tc) HiPerDSP stops at 21
I have one HiPER DSP that has 21 active calls and then returns a busy signal, even though there should be three more modems available. Any suggestions as to why this is happening?
David
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Yesterday I checked all the DSP Modem programmed settings. The channels that have not been working are 3, 23, & 24. The only differences in the settings of these three and the rest that are working was in the Call Control Options. The Verbal/Numeric Result codes on the three was set at Verbal instead of Numeric. The Result Code Groups (X) was 1 instead of 0, and Rings for Auto Answer (SO|Dip 5) was 1 instead of 0. I changed these and then rebooted the card. Didn't help. Last night it still stopped at 21 calls with those three channels not working. This morning, I pulled the card out and re-inserted it. When calls came in, Channel three was skipped. Channels 1,2, 4, 5, 6 accepted calls. I have reported this to the telco and they are checking their end. Any more ideas? Running DSP code 2.0.60 David At 09:35 PM 1/25/2000 -0600, you wrote:
See if you telco capped your inbound available calls...
JN
----- Original Message ----- From: "David Swearingin" <david@carolnet.com> To: <usr-tc@lists.xmission.com> Sent: Monday, January 24, 2000 12:00 AM Subject: (usr-tc) HiPerDSP stops at 21
I have one HiPER DSP that has 21 active calls and then returns a busy signal, even though there should be three more modems available. Any suggestions as to why this is happening?
David
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
__________________________________________________ David Swearingin (david@carolnet.com) CARROLLTON INTERNET SERVICE (www.carolnet.com) First Financial Group, Inc. 11 N. Folger, Carrollton, MO 64633 660-542-3002 Fax 660-542-3003 - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
get into the dsp chdev span dis atstat dis atab what do those show? you did check your channel/modem mapping right? On Wed, 26 Jan 2000, David Swearingin wrote:
Yesterday I checked all the DSP Modem programmed settings. The channels that have not been working are 3, 23, & 24. The only differences in the settings of these three and the rest that are working was in the Call Control Options. The Verbal/Numeric Result codes on the three was set at Verbal instead of Numeric. The Result Code Groups (X) was 1 instead of 0, and Rings for Auto Answer (SO|Dip 5) was 1 instead of 0. I changed these and then rebooted the card.
Didn't help. Last night it still stopped at 21 calls with those three channels not working. This morning, I pulled the card out and re-inserted it. When calls came in, Channel three was skipped. Channels 1,2, 4, 5, 6 accepted calls.
I have reported this to the telco and they are checking their end.
Any more ideas? Running DSP code 2.0.60
David
At 09:35 PM 1/25/2000 -0600, you wrote:
See if you telco capped your inbound available calls...
JN
----- Original Message ----- From: "David Swearingin" <david@carolnet.com> To: <usr-tc@lists.xmission.com> Sent: Monday, January 24, 2000 12:00 AM Subject: (usr-tc) HiPerDSP stops at 21
I have one HiPER DSP that has 21 active calls and then returns a busy signal, even though there should be three more modems available. Any suggestions as to why this is happening?
David
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
__________________________________________________ David Swearingin (david@carolnet.com) CARROLLTON INTERNET SERVICE (www.carolnet.com) First Financial Group, Inc. 11 N. Folger, Carrollton, MO 64633 660-542-3002 Fax 660-542-3003
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
----------------------------------------------------- Brian Feeny (BF304) signal@shreve.net 318-222-2638 x 109 http://www.shreve.net/~signal Network Administrator ShreveNet Inc. (ASN 11881) - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
participants (3)
-
Brian -
david＠carolnet.com -
Jason A. Nunnelley