I have heard this discussed before but never had it happen to us till now. What could be causing one of our DSP card to continually reboot itself. After reboting it will take calls fine then 10 to 30 mins later it will reboot again? Thanks in advance Greg Owens Magnolia Internet Services http://www.magnolia-net.com - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Greg, This happened to one here too, I re-flashed the code, did hardware reset remotely, then re-seated the card to no avail. 3Com logistics issued a RMA and repaired the card. The NIC was ok it turned out to be components on the DSP. Dave Lajoie RA Administrator North Country Internet Access www.ncia.net E-Mail: dave@ncia.net On Thu, 2 Mar 2000, Greg Owens wrote:
I have heard this discussed before but never had it happen to us till now. What could be causing one of our DSP card to continually reboot itself. After reboting it will take calls fine then 10 to 30 mins later it will reboot again? Thanks in advance Greg Owens Magnolia Internet Services http://www.magnolia-net.com
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
In TCM, do an inventory. If you have hardware revision 0.55.0 then there is the problem. You need to put software version 2.0.51 on those DSP's to resolve the issue. I'm running version 2.0.51 on all my DSP's, it runs well. If you don't have version 0.55.0, or you're already running 2.0.51 code, it's probably a bad DSP. __________________________________ Justin Ellison System Administrator InternetUSA sysadmin@nebi.com http://nebi.com 800-603-3502
-----Original Message----- From: owner-usr-tc@lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of Dave Lajoie Sent: Friday, March 03, 2000 7:32 AM To: usr-tc@lists.xmission.com Subject: Re: (usr-tc) DSP rebooting
Greg,
This happened to one here too, I re-flashed the code, did hardware reset remotely, then re-seated the card to no avail. 3Com logistics issued a RMA and repaired the card. The NIC was ok it turned out to be components on the DSP.
Dave Lajoie RA Administrator North Country Internet Access www.ncia.net E-Mail: dave@ncia.net
On Thu, 2 Mar 2000, Greg Owens wrote:
I have heard this discussed before but never had it happen to us till now. What could be causing one of our DSP card to continually reboot itself. After reboting it will take calls fine then 10 to 30 mins later it will reboot again? Thanks in advance Greg Owens Magnolia Internet Services http://www.magnolia-net.com
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Thanks...Did a hard reboot this morning and so far have not seen the problem anymore. I will check the code and go from there. Thanks Greg Owens Magnolia Internet Services http://www.magnolia-net.com ----- Original Message ----- From: System Administrator <sysadmin@nebi.com> To: <usr-tc@lists.xmission.com> Sent: Friday, March 03, 2000 8:57 AM Subject: RE: (usr-tc) DSP rebooting
In TCM, do an inventory. If you have hardware revision 0.55.0 then there is the problem. You need to put software version 2.0.51 on those DSP's to resolve the issue. I'm running version 2.0.51 on all my DSP's, it runs well.
If you don't have version 0.55.0, or you're already running 2.0.51 code, it's probably a bad DSP.
__________________________________ Justin Ellison System Administrator InternetUSA sysadmin@nebi.com http://nebi.com 800-603-3502
-----Original Message----- From: owner-usr-tc@lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of Dave Lajoie Sent: Friday, March 03, 2000 7:32 AM To: usr-tc@lists.xmission.com Subject: Re: (usr-tc) DSP rebooting
Greg,
This happened to one here too, I re-flashed the code, did hardware reset remotely, then re-seated the card to no avail. 3Com logistics issued a RMA and repaired the card. The NIC was ok it turned out to be components on the DSP.
Dave Lajoie RA Administrator North Country Internet Access www.ncia.net E-Mail: dave@ncia.net
On Thu, 2 Mar 2000, Greg Owens wrote:
I have heard this discussed before but never had it happen to us till now. What could be causing one of our DSP card to continually reboot itself. After reboting it will take calls fine then 10 to 30 mins later it will reboot again? Thanks in advance Greg Owens Magnolia Internet Services http://www.magnolia-net.com
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Ok we are running Hardware ver. .49 and DSP ver. 2.0.60 Now if I load load 2.0.51 am I going to a newer code or an older one? I swear I can never keep it straight what order which codes go Greg Owens Magnolia Internet Services http://www.magnolia-net.com ----- Original Message ----- From: System Administrator <sysadmin@nebi.com> To: <usr-tc@lists.xmission.com> Sent: Friday, March 03, 2000 8:57 AM Subject: RE: (usr-tc) DSP rebooting
In TCM, do an inventory. If you have hardware revision 0.55.0 then there is the problem. You need to put software version 2.0.51 on those DSP's to resolve the issue. I'm running version 2.0.51 on all my DSP's, it runs well.
If you don't have version 0.55.0, or you're already running 2.0.51 code, it's probably a bad DSP.
__________________________________ Justin Ellison System Administrator InternetUSA sysadmin@nebi.com http://nebi.com 800-603-3502
-----Original Message----- From: owner-usr-tc@lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of Dave Lajoie Sent: Friday, March 03, 2000 7:32 AM To: usr-tc@lists.xmission.com Subject: Re: (usr-tc) DSP rebooting
Greg,
This happened to one here too, I re-flashed the code, did hardware reset remotely, then re-seated the card to no avail. 3Com logistics issued a RMA and repaired the card. The NIC was ok it turned out to be components on the DSP.
Dave Lajoie RA Administrator North Country Internet Access www.ncia.net E-Mail: dave@ncia.net
On Thu, 2 Mar 2000, Greg Owens wrote:
I have heard this discussed before but never had it happen to us till now. What could be causing one of our DSP card to continually reboot itself. After reboting it will take calls fine then 10 to 30 mins later it will reboot again? Thanks in advance Greg Owens Magnolia Internet Services http://www.magnolia-net.com
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Newer. At 09:26 AM 3/4/00 -0600, you wrote:
Ok we are running Hardware ver. .49 and DSP ver. 2.0.60 Now if I load load 2.0.51 am I going to a newer code or an older one? I swear I can never keep it straight what order which codes go
Greg Owens Magnolia Internet Services http://www.magnolia-net.com ----- Original Message ----- From: System Administrator <sysadmin@nebi.com> To: <usr-tc@lists.xmission.com> Sent: Friday, March 03, 2000 8:57 AM Subject: RE: (usr-tc) DSP rebooting
In TCM, do an inventory. If you have hardware revision 0.55.0 then there is the problem. You need to put software version 2.0.51 on those DSP's to resolve the issue. I'm running version 2.0.51 on all my DSP's, it runs well.
If you don't have version 0.55.0, or you're already running 2.0.51 code, it's probably a bad DSP.
__________________________________ Justin Ellison System Administrator InternetUSA sysadmin@nebi.com http://nebi.com 800-603-3502
-----Original Message----- From: owner-usr-tc@lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of Dave Lajoie Sent: Friday, March 03, 2000 7:32 AM To: usr-tc@lists.xmission.com Subject: Re: (usr-tc) DSP rebooting
Greg,
This happened to one here too, I re-flashed the code, did hardware reset remotely, then re-seated the card to no avail. 3Com logistics issued a RMA and repaired the card. The NIC was ok it turned out to be components on the DSP.
Dave Lajoie RA Administrator North Country Internet Access www.ncia.net E-Mail: dave@ncia.net
On Thu, 2 Mar 2000, Greg Owens wrote:
I have heard this discussed before but never had it happen to us till now. What could be causing one of our DSP card to continually reboot itself. After reboting it will take calls fine then 10 to 30 mins later it will reboot again? Thanks in advance Greg Owens Magnolia Internet Services http://www.magnolia-net.com
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Thanks, Greg Coffey, Visionary Communications V 307-234-5443 F 307-234-5446 ===================================================================== 100 N. Center St. #100, Casper, WY 82601 WWW.VCN.COM __________________________________________________________ Fight spam now! Get your free anti-spam service at http://www.brightmail.com - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
participants (4)
-
Dave Lajoie -
Greg Coffey -
Greg Owens -
System Administrator