(usr-tc) Is there a way to not accept anonymous calls?
Is there any way to configure a PRI (on the Netserver PRI, or the DSP), to not accept a call w/o caller-ID info? If it's just not available because of equipment, that's fine, but if the caller is specifically blocking the c-id, then I want to not accept the call on the rack... Is this doable? - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Quoting Jaye Mathisen <mrcpu@internetcds.com>:
Is there any way to configure a PRI (on the Netserver PRI, or the DSP), to not accept a call w/o caller-ID info?
If it's just not available because of equipment, that's fine, but if the caller is specifically blocking the c-id, then I want to not accept the call on the rack...
Is this doable?
Can be done several ways. Using Radius - You can tell radius to expect certain number of digits to validate the user by checking ani. There is configuration on the hiper arc when you can force the hiper arc to check for the ani/dnis (not really sure how to configure - need to look at the manual) but you can tell the hiper arc to do pre-auth on ani/dnis You can also tell the DSP - set it to dtfm - check for address and program it for checking the amount ani digits the telco provides. -V
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
=========== -V ========== - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Also sprach Veda Narayan
Quoting Jaye Mathisen <mrcpu@internetcds.com>:
Is there any way to configure a PRI (on the Netserver PRI, or the DSP), to not accept a call w/o caller-ID info?
If it's just not available because of equipment, that's fine, but if the caller is specifically blocking the c-id, then I want to not accept the call on the rack...
Is this doable?
Can be done several ways. Using Radius - You can tell radius to expect certain number of digits to validate the user by checking ani.
There is configuration on the hiper arc when you can force the hiper arc to check for the ani/dnis (not really sure how to configure - need to look at the manual) but you can tell the hiper arc to do pre-auth on ani/dnis
You can also tell the DSP - set it to dtfm - check for address and program it for checking the amount ani digits the telco provides.
Yeah, but from what I've seen, you can't distinguish between callerid blocking (note, its really caller id, not ANI) and just plain non-existence, which is what the question really was I believe. ie, if I'm calling from my work PBX, it doesn't have the ability to encode callerid information into the call request (at least the way we have it set up...I think the equipment is capable of it), that's different from someone dialing a *xx before they dial to block the callerid information. -- Jeff McAdams Email: jeffm@iglou.com Head Network Administrator Voice: (502) 966-3848 IgLou Internet Services (800) 436-4456 - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
THis is exactly what I mean. I guess I can go back to our switch and pull the CDR's and figure it out, but it would just be easier to do it at the 3com. Wasn't sure if there was a difference in signalling between the CID stuff not being available and the CID stuff being specifically blocked. On Sat, 12 Aug 2000, Jeff Mcadams wrote:
Also sprach Veda Narayan
Quoting Jaye Mathisen <mrcpu@internetcds.com>:
Is there any way to configure a PRI (on the Netserver PRI, or the DSP), to not accept a call w/o caller-ID info?
If it's just not available because of equipment, that's fine, but if the caller is specifically blocking the c-id, then I want to not accept the call on the rack...
Is this doable?
Can be done several ways. Using Radius - You can tell radius to expect certain number of digits to validate the user by checking ani.
There is configuration on the hiper arc when you can force the hiper arc to check for the ani/dnis (not really sure how to configure - need to look at the manual) but you can tell the hiper arc to do pre-auth on ani/dnis
You can also tell the DSP - set it to dtfm - check for address and program it for checking the amount ani digits the telco provides.
Yeah, but from what I've seen, you can't distinguish between callerid blocking (note, its really caller id, not ANI) and just plain non-existence, which is what the question really was I believe. ie, if I'm calling from my work PBX, it doesn't have the ability to encode callerid information into the call request (at least the way we have it set up...I think the equipment is capable of it), that's different from someone dialing a *xx before they dial to block the callerid information.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
participants (3)
-
Jaye Mathisen -
Jeff Mcadams -
Veda Narayan