PRI vs. Channelized T1
I bought a TC chassis with two (2) HyperDSP cards, a HyperARC, and HiperNMC card. I was going to use it as a backup chassis for my existing Quad modem chassing running with a Channelized T1, but now I'm ordering a PRI circuit to replace the T1, since it's cheaper and more reliable, and I want to use new chassis on the PRI. How do I tell if the new HiperDSP cards are flashed for T1 or PRI? I'm running TCM v6.0.23. I've never flashed any cards before and here are the files I recevied with the unit. -rw-r--r-- 1 wie-web site23 3850727 Oct 18 2002 HiPer ARC_Access Router Card v5_3_2.zip -rw-r--r-- 1 wie-web site23 1279591 Oct 18 2002 HiPer DSP E1_PRI v3_5_13.zip -rw-r--r-- 1 wie-web site23 1270724 Oct 18 2002 HiPer DSP v3_5_12.zip -rw-r--r-- 1 wie-web site23 859585 Oct 18 2002 HiPer NMCv8_6_3.zip -rw-r--r-- 1 wie-web site23 1629631 Oct 18 2002 Maintenance Guide.pdf -rw-r--r-- 1 wie-web site23 1546963 Oct 18 2002 MutliSpan DSP T1_PRI v3_5_12.zip -rw-r--r-- 1 wie-web site23 859606 Oct 18 2002 NMC333v8_7_3.zip -rw-r--r-- 1 wie-web site23 1371270 Oct 18 2002 Trouble Locating and Clearing Guide.pdf -rw-r--r-- 1 wie-web site23 1354444 Oct 18 2002 harm118win.zip -rw-r--r-- 1 wie-web site23 512000 Oct 18 2002 hd35103.zip -rw-r--r-- 1 wie-web site23 1269359 Oct 18 2002 hd35105.zip -rw-r--r-- 1 wie-web site23 3870614 Oct 18 2002 ne050303.zip -rw-r--r-- 1 wie-web site23 3865908 Oct 18 2002 ne0503107.zip -rw-r--r-- 1 wie-web site23 17345026 Oct 18 2002 tcm080206.zip Scott Wiersum scott@smartgate.com
You don't have to flash them. Just change the span setting in TCM. Highlight the top portion of the dsp card (the 5 or so LEDs)...click configure...programmed settings...trunk settings...and change the signal mode to message oriented. Don't forget to also make sure you have the correct switch type selected. Todd ----- Original Message ----- From: "Scott Wiersum" <scott@smartgate.com> To: <usr-tc@mailman.xmission.com> Sent: Thursday, July 31, 2003 9:07 AM Subject: [USR-TC] PRI vs. Channelized T1
I bought a TC chassis with two (2) HyperDSP cards, a HyperARC, and HiperNMC card. I was going to use it as a backup chassis for my existing Quad modem chassing running with a Channelized T1, but now I'm ordering a PRI circuit to replace the T1, since it's cheaper and more reliable, and I want to use new chassis on the PRI.
How do I tell if the new HiperDSP cards are flashed for T1 or PRI? I'm running TCM v6.0.23. I've never flashed any cards before and here are the files I recevied with the unit.
-rw-r--r-- 1 wie-web site23 3850727 Oct 18 2002 HiPer ARC_Access Router Card v5_3_2.zip -rw-r--r-- 1 wie-web site23 1279591 Oct 18 2002 HiPer DSP E1_PRI v3_5_13.zip -rw-r--r-- 1 wie-web site23 1270724 Oct 18 2002 HiPer DSP v3_5_12.zip -rw-r--r-- 1 wie-web site23 859585 Oct 18 2002 HiPer NMCv8_6_3.zip -rw-r--r-- 1 wie-web site23 1629631 Oct 18 2002 Maintenance Guide.pdf -rw-r--r-- 1 wie-web site23 1546963 Oct 18 2002 MutliSpan DSP T1_PRI v3_5_12.zip -rw-r--r-- 1 wie-web site23 859606 Oct 18 2002 NMC333v8_7_3.zip -rw-r--r-- 1 wie-web site23 1371270 Oct 18 2002 Trouble Locating and Clearing Guide.pdf -rw-r--r-- 1 wie-web site23 1354444 Oct 18 2002 harm118win.zip -rw-r--r-- 1 wie-web site23 512000 Oct 18 2002 hd35103.zip -rw-r--r-- 1 wie-web site23 1269359 Oct 18 2002 hd35105.zip -rw-r--r-- 1 wie-web site23 3870614 Oct 18 2002 ne050303.zip -rw-r--r-- 1 wie-web site23 3865908 Oct 18 2002 ne0503107.zip -rw-r--r-- 1 wie-web site23 17345026 Oct 18 2002 tcm080206.zip
Scott Wiersum scott@smartgate.com
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
You were supplied with TCS 4.5 (V.92) code. Which translates into being able to use (V.44, Quick Connect phase 1 & 2, and PCM Upstream up to 33k). I have V.44 and Quick connect enabled, but disabled PCM Upstream and MoH. It's my understanding that MoH was not fully implemented in TCS 4.5 anyway. If you plan on using the supplied code on your cards you need to install that TCM080206.zip file first. You'll then need to install the following: Hiper DSP 3.5.12 (if you ever downgrade code, pay attention to the release notes or use DSP for doorstop) Hiper ARC 5.3.3 (we had crash/reboot issues with this code, and are currently running 5.3.108) Hiper NMC 8.6.3 http://totalservice.utstar.com/Matrixs/tcsmatrix.cfm Should you choose to purchase a support contract for your chassis, I'd suggest you try one of the following. There are more, but these are the ones I'm familiar with. http://www.source-t.com/ http://www.solunet.com/ For use of the knowledgebase just register and search. No Support Contract necessary. http://totalservice.utstar.com/ Good luck, Adam -----Original Message----- From: usr-tc-bounces@mailman.xmission.com [mailto:usr-tc-bounces@mailman.xmission.com] On Behalf Of Scott Wiersum Sent: Thursday, July 31, 2003 8:07 AM To: usr-tc@mailman.xmission.com Subject: [USR-TC] PRI vs. Channelized T1 I bought a TC chassis with two (2) HyperDSP cards, a HyperARC, and HiperNMC card. I was going to use it as a backup chassis for my existing Quad modem chassing running with a Channelized T1, but now I'm ordering a PRI circuit to replace the T1, since it's cheaper and more reliable, and I want to use new chassis on the PRI. How do I tell if the new HiperDSP cards are flashed for T1 or PRI? I'm running TCM v6.0.23. I've never flashed any cards before and here are the files I recevied with the unit. -rw-r--r-- 1 wie-web site23 3850727 Oct 18 2002 HiPer ARC_Access Router Card v5_3_2.zip -rw-r--r-- 1 wie-web site23 1279591 Oct 18 2002 HiPer DSP E1_PRI v3_5_13.zip -rw-r--r-- 1 wie-web site23 1270724 Oct 18 2002 HiPer DSP v3_5_12.zip -rw-r--r-- 1 wie-web site23 859585 Oct 18 2002 HiPer NMCv8_6_3.zip -rw-r--r-- 1 wie-web site23 1629631 Oct 18 2002 Maintenance Guide.pdf -rw-r--r-- 1 wie-web site23 1546963 Oct 18 2002 MutliSpan DSP T1_PRI v3_5_12.zip -rw-r--r-- 1 wie-web site23 859606 Oct 18 2002 NMC333v8_7_3.zip -rw-r--r-- 1 wie-web site23 1371270 Oct 18 2002 Trouble Locating and Clearing Guide.pdf -rw-r--r-- 1 wie-web site23 1354444 Oct 18 2002 harm118win.zip -rw-r--r-- 1 wie-web site23 512000 Oct 18 2002 hd35103.zip -rw-r--r-- 1 wie-web site23 1269359 Oct 18 2002 hd35105.zip -rw-r--r-- 1 wie-web site23 3870614 Oct 18 2002 ne050303.zip -rw-r--r-- 1 wie-web site23 3865908 Oct 18 2002 ne0503107.zip -rw-r--r-- 1 wie-web site23 17345026 Oct 18 2002 tcm080206.zip Scott Wiersum scott@smartgate.com _______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
V.44? Today I disabled this feature. Some users of Courier V.Everything was undable to connect. This was true, because when I tried to connect I was unable to. (After disabling hardware commpression and error correction on my side I got connected). After disabling V.44 I successfully connected. Software: HiPer DSP E1/R2 v3.5.109 HARC: v5.3.3 P.S. sorry for my english if I have some mistakes. Adam Barnhill wrote:
You were supplied with TCS 4.5 (V.92) code. Which translates into being able to use (V.44, Quick Connect phase 1 & 2, and PCM Upstream up to 33k). I have V.44 and Quick connect enabled, but disabled PCM Upstream and MoH. It's my understanding that MoH was not fully implemented in TCS 4.5 anyway.
If you plan on using the supplied code on your cards you need to install that TCM080206.zip file first.
You'll then need to install the following: Hiper DSP 3.5.12 (if you ever downgrade code, pay attention to the release notes or use DSP for doorstop) Hiper ARC 5.3.3 (we had crash/reboot issues with this code, and are currently running 5.3.108) Hiper NMC 8.6.3
http://totalservice.utstar.com/Matrixs/tcsmatrix.cfm
Should you choose to purchase a support contract for your chassis, I'd suggest you try one of the following. There are more, but these are the ones I'm familiar with. http://www.source-t.com/ http://www.solunet.com/
For use of the knowledgebase just register and search. No Support Contract necessary. http://totalservice.utstar.com/
Good luck, Adam
-----Original Message----- From: usr-tc-bounces@mailman.xmission.com [mailto:usr-tc-bounces@mailman.xmission.com] On Behalf Of Scott Wiersum Sent: Thursday, July 31, 2003 8:07 AM To: usr-tc@mailman.xmission.com Subject: [USR-TC] PRI vs. Channelized T1
I bought a TC chassis with two (2) HyperDSP cards, a HyperARC, and HiperNMC card. I was going to use it as a backup chassis for my existing Quad modem chassing running with a Channelized T1, but now I'm ordering a PRI circuit to replace the T1, since it's cheaper and more reliable, and I want to use new chassis on the PRI.
How do I tell if the new HiperDSP cards are flashed for T1 or PRI? I'm running TCM v6.0.23. I've never flashed any cards before and here are the files I recevied with the unit.
-rw-r--r-- 1 wie-web site23 3850727 Oct 18 2002 HiPer ARC_Access Router Card v5_3_2.zip -rw-r--r-- 1 wie-web site23 1279591 Oct 18 2002 HiPer DSP E1_PRI v3_5_13.zip -rw-r--r-- 1 wie-web site23 1270724 Oct 18 2002 HiPer DSP v3_5_12.zip -rw-r--r-- 1 wie-web site23 859585 Oct 18 2002 HiPer NMCv8_6_3.zip -rw-r--r-- 1 wie-web site23 1629631 Oct 18 2002 Maintenance Guide.pdf -rw-r--r-- 1 wie-web site23 1546963 Oct 18 2002 MutliSpan DSP T1_PRI v3_5_12.zip -rw-r--r-- 1 wie-web site23 859606 Oct 18 2002 NMC333v8_7_3.zip -rw-r--r-- 1 wie-web site23 1371270 Oct 18 2002 Trouble Locating and Clearing Guide.pdf -rw-r--r-- 1 wie-web site23 1354444 Oct 18 2002 harm118win.zip -rw-r--r-- 1 wie-web site23 512000 Oct 18 2002 hd35103.zip -rw-r--r-- 1 wie-web site23 1269359 Oct 18 2002 hd35105.zip -rw-r--r-- 1 wie-web site23 3870614 Oct 18 2002 ne050303.zip -rw-r--r-- 1 wie-web site23 3865908 Oct 18 2002 ne0503107.zip -rw-r--r-- 1 wie-web site23 17345026 Oct 18 2002 tcm080206.zip
Scott Wiersum scott@smartgate.com
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
----- Original Message ----- From: "Adam Barnhill" <adam@semo.net> To: "'Discussion relating to the 3Com/US Robotics Total Controlmodemsystems.'" <usr-tc@mailman.xmission.com> Sent: Thursday, July 31, 2003 09:45 AM Subject: RE: [USR-TC] PRI vs. Channelized T1 You were supplied with TCS 4.5 (V.92) code. Which translates into being able to use (V.44, Quick Connect phase 1 & 2, and PCM Upstream up to 33k). I have V.44 and Quick connect enabled, but disabled PCM Upstream and MoH. It's my understanding that MoH was not fully implemented in TCS 4.5 anyway. If you plan on using the supplied code on your cards you need to install that TCM080206.zip file first. You'll then need to install the following: Hiper DSP 3.5.12 (if you ever downgrade code, pay attention to the release notes or use DSP for doorstop) Hiper ARC 5.3.3 (we had crash/reboot issues with this code, and are currently running 5.3.108) Hiper NMC 8.6.3 http://totalservice.utstar.com/Matrixs/tcsmatrix.cfm Should you choose to purchase a support contract for your chassis, I'd suggest you try one of the following. There are more, but these are the ones I'm familiar with. http://www.source-t.com/ http://www.solunet.com/ For use of the knowledgebase just register and search. No Support Contract necessary. http://totalservice.utstar.com/ Good luck, Adam -----Original Message----- From: usr-tc-bounces@mailman.xmission.com [mailto:usr-tc-bounces@mailman.xmission.com] On Behalf Of Scott Wiersum Sent: Thursday, July 31, 2003 8:07 AM To: usr-tc@mailman.xmission.com Subject: [USR-TC] PRI vs. Channelized T1 I bought a TC chassis with two (2) HyperDSP cards, a HyperARC, and HiperNMC card. I was going to use it as a backup chassis for my existing Quad modem chassing running with a Channelized T1, but now I'm ordering a PRI circuit to replace the T1, since it's cheaper and more reliable, and I want to use new chassis on the PRI. How do I tell if the new HiperDSP cards are flashed for T1 or PRI? I'm running TCM v6.0.23. I've never flashed any cards before and here are the files I recevied with the unit. -rw-r--r-- 1 wie-web site23 3850727 Oct 18 2002 HiPer ARC_Access Router Card v5_3_2.zip -rw-r--r-- 1 wie-web site23 1279591 Oct 18 2002 HiPer DSP E1_PRI v3_5_13.zip -rw-r--r-- 1 wie-web site23 1270724 Oct 18 2002 HiPer DSP v3_5_12.zip -rw-r--r-- 1 wie-web site23 859585 Oct 18 2002 HiPer NMCv8_6_3.zip -rw-r--r-- 1 wie-web site23 1629631 Oct 18 2002 Maintenance Guide.pdf -rw-r--r-- 1 wie-web site23 1546963 Oct 18 2002 MutliSpan DSP T1_PRI v3_5_12.zip -rw-r--r-- 1 wie-web site23 859606 Oct 18 2002 NMC333v8_7_3.zip -rw-r--r-- 1 wie-web site23 1371270 Oct 18 2002 Trouble Locating and Clearing Guide.pdf -rw-r--r-- 1 wie-web site23 1354444 Oct 18 2002 harm118win.zip -rw-r--r-- 1 wie-web site23 512000 Oct 18 2002 hd35103.zip -rw-r--r-- 1 wie-web site23 1269359 Oct 18 2002 hd35105.zip -rw-r--r-- 1 wie-web site23 3870614 Oct 18 2002 ne050303.zip -rw-r--r-- 1 wie-web site23 3865908 Oct 18 2002 ne0503107.zip -rw-r--r-- 1 wie-web site23 17345026 Oct 18 2002 tcm080206.zip Scott Wiersum scott@smartgate.com _______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
participants (5)
-
Adam Barnhill -
alex -
Scott Wiersum -
Todd Bertolozzi -
WayneG