(usr-tc) pri dsp d-channel problem
I have a new PRI (new DSP card for that matter) installed in an existing chassis. I am getting a LPBK/D-Chan red alarm on the new span. So I am obviously getting no calls being terminated on my equipment. When I pull up a com session into the DSP and do a display d-chan , I get span1> display d-chan Span1 D-channel Operational is: DOWN software: Software Version 2.0.19 Regulatory Version 1.0 Other than this all looks fine, it is supposedly configed the same as an existing circuit which is working fine. My DSPs are configged the same way. Sprint has dispatched a tech and says that all is fine as far as they can see. Is it possible that I have missed a setting somewhere that would cause this same reaction? steve Steve McConnell EMJI 919-303-3217 888-258-8959 - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Never mind. Losers at sprint did not have the d-channel turned on. For a week, I have been calling them every single day, sometimes hourly, checking on the ticket, asking to speak to provisioning (because I was pretty sure this was the problem) telling them the D-channel was not turned on. So today I waste the entire day sitting here waiting for sprint to dispatch a tech to come ourt and look (for the 4th time) at the circuit (never mind that I freaking told them it was a d-channel/provisioning problem) Unbelievable. Thanks matthew for the fast response. Works like a dream now... steve --On Wednesday, October 06, 1999, 1:28 PM -0400 Steve McConnell <stevem@emji.net> wrote:
I have a new PRI (new DSP card for that matter) installed in an existing chassis.
I am getting a LPBK/D-Chan red alarm on the new span. So I am obviously getting no calls being terminated on my equipment.
When I pull up a com session into the DSP and do a display d-chan , I get
span1> display d-chan Span1 D-channel Operational is: DOWN
software: Software Version 2.0.19 Regulatory Version 1.0
Other than this all looks fine, it is supposedly configed the same as an existing circuit which is working fine. My DSPs are configged the same way. Sprint has dispatched a tech and says that all is fine as far as they can see. Is it possible that I have missed a setting somewhere that would cause this same reaction?
steve
Steve McConnell EMJI 919-303-3217 888-258-8959
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Steve McConnell EMJI 919-303-3217 888-258-8959 - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
You know I had the exact same problem with my telco yesterday. Thanks, Aaron Steve McConnell wrote:
Never mind.
Losers at sprint did not have the d-channel turned on.
For a week, I have been calling them every single day, sometimes hourly, checking on the ticket, asking to speak to provisioning (because I was pretty sure this was the problem) telling them the D-channel was not turned on.
So today I waste the entire day sitting here waiting for sprint to dispatch a tech to come ourt and look (for the 4th time) at the circuit (never mind that I freaking told them it was a d-channel/provisioning problem)
Unbelievable.
Thanks matthew for the fast response.
Works like a dream now...
steve
--On Wednesday, October 06, 1999, 1:28 PM -0400 Steve McConnell <stevem@emji.net> wrote:
I have a new PRI (new DSP card for that matter) installed in an existing chassis.
I am getting a LPBK/D-Chan red alarm on the new span. So I am obviously getting no calls being terminated on my equipment.
When I pull up a com session into the DSP and do a display d-chan , I get
span1> display d-chan Span1 D-channel Operational is: DOWN
software: Software Version 2.0.19 Regulatory Version 1.0
Other than this all looks fine, it is supposedly configed the same as an existing circuit which is working fine. My DSPs are configged the same way. Sprint has dispatched a tech and says that all is fine as far as they can see. Is it possible that I have missed a setting somewhere that would cause this same reaction?
steve
Steve McConnell EMJI 919-303-3217 888-258-8959
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Steve McConnell EMJI 919-303-3217 888-258-8959
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
participants (2)
-
Dataheart -
Steve McConnell