Joel: (1) I did not load factory settings. I do not not know how? I will read the manual and figure it out. If someone has a quick answer as to how to load the factory settings on a HiPer DSP, let me know! (2) I do not know what a carrier sound is so I can not tell if my box is also answering on the first ring. I do notice that it takes appox 30 seconds for the handshake (or it may be the same as carrier sound). My impression was that the connection time, from dialing in to UID/PW verification is about 8-10 seconds and not 30 seconds. I am learning and thank people like you to respond. I am also hoping that I get more response on this post. Kirti -----Original Message----- From: Joel - Fox Computers [mailto:jfox@foxcomputers.com] Sent: Saturday, January 29, 2005 12:45 PM To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. Subject: RE: [USR-TC] Tune-up Mine never rings at all, soon as you dial, you hear carrier. Your switch type probably isn't set right yet. Or some other trunk setting is not configured correctly. You did load factory defaults on the DSP? If you didn't, then I'd say you need to. If this happens after you've loaded defaults and set your switch type, then your switch type is probably wrong. You have to understand that there's a LOT more to this than just ringing, answering, and connecting. You can have a lot of things wrong and it will still do that. But if something's wrong you can have the long answering delay, slow modem communication, a lot of disconnects, etc. You have to load defaults and verify the correct switch setting, or you're just asking for problems. - Joel -----Original Message----- From: Kirti S. Bajwa [mailto:kbajwa@tib.com] Sent: Saturday, January 29, 2005 9:21 AM To: 'Discussion relating to the 3Com/US Robotics Total Control modemsystems.' Subject: [USR-TC] Tune-up Hello List: Finally I have 3COM responding to Dial-in & is working. Thank you all for all the help & suggestions. Without your help, I will still be scratching my head. Next question. I notice that when I dial-in, 3COM is letting the phone/connection ring for about 30 seconds before the authentication sequence is started. I have set the modems (HiPer DSP) to answer on the first ring. Why does it take so long? Are there any tune-up settings for 3COM? Kirti _______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
Kirti S. Bajwa wrote:
Joel:
(1) I did not load factory settings. I do not not know how? I will read the manual and figure it out. If someone has a quick answer as to how to load the factory settings on a HiPer DSP, let me know!
(2) I do not know what a carrier sound is so I can not tell if my box is also answering on the first ring. I do notice that it takes appox 30 seconds for the handshake (or it may be the same as carrier sound). My impression was that the connection time, from dialing in to UID/PW verification is about 8-10 seconds and not 30 seconds.
I am learning and thank people like you to respond. I am also hoping that I get more response on this post.
Kirti The long answer delay might also be on the phone company side. I own my own class 5 switch that sits in front of my TC. One type of Answer Supervision is "10 digit/3second", another is "immediate". I doubt this is it but for clarity sakes there are different settings that can affect this. If you are using PRI then I believe this issetup in the switch type and you shouldn't even hear a ring. -- Lewis Bergman Texas Communications 4309 Maple St. Abilene, TX 79602-8044 325-691-3301 800-299-6962
participants (2)
-
Kirti S. Bajwa -
Lewis Bergman