Hi, I got a good deal on some refurbished Hiper DSP cards. The issue is - the guy says they work on T1. Unfortunately E1 is my only choice. What gives me some hope is that on the back of the chassis one can see the sign "Hiper DSP T1/E1 NIC". Also, some voice gateways (like Quintum) can switch the port from T1 to E1 (and vice versa) only by changing a simple settings inside them. So, my main question is - can I upload an E1 firmware (R2 CAS) into the Hiper DSP card with the idea to switch it from T1 to E1 ?
Thu, Sep 29, 2005 at 10:59:24AM +0300, Teodor Georgiev wrote:
I got a good deal on some refurbished Hiper DSP cards. The issue is - the guy says they work on T1. Unfortunately E1 is my only choice. What gives me some hope is that on the back of the chassis one can see the sign "Hiper DSP T1/E1 NIC". Also, some voice gateways (like Quintum) can switch the port from T1 to E1 (and vice versa) only by changing a simple settings inside them.
So, my main question is - can I upload an E1 firmware (R2 CAS) into the Hiper DSP card with the idea to switch it from T1 to E1 ?
It depends entirely on the generation of the card. The most common answer is no, you can't. I went through the same thing before. Bascially, contact Commworks and give them the part number of your NAC cards and ask if they are able to be firmware flashed with E1 code. Only newer NACs supported both E1 and T1 firmware. Patrick
NAC PN# for E1 should be... 69-002072-00 69-003546-00 other than that you can... take an T1/PRI card, install daughtercard (E1) from ..2072-00 NAC and flash T1 DSP for E1 and that works. At 04:08 AM 9/29/2005, you wrote:
Thu, Sep 29, 2005 at 10:59:24AM +0300, Teodor Georgiev wrote:
I got a good deal on some refurbished Hiper DSP cards. The issue is - the guy says they work on T1. Unfortunately E1 is my only choice. What gives me some hope is that on the back of the chassis one can see the sign "Hiper DSP T1/E1 NIC". Also, some voice gateways (like Quintum) can switch the port from T1 to E1 (and vice versa) only by changing a simple settings inside them.
So, my main question is - can I upload an E1 firmware (R2 CAS) into the Hiper DSP card with the idea to switch it from T1 to E1 ?
It depends entirely on the generation of the card. The most common answer is no, you can't. I went through the same thing before. Bascially, contact Commworks and give them the part number of your NAC cards and ask if they are able to be firmware flashed with E1 code. Only newer NACs supported both E1 and T1 firmware.
Patrick
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
Hi, do you mean these are the PN# i should look for that if I want to flash a T1 to E1? Where can I get the flash software, can u help me? thanks Richard
NAC PN# for E1 should be... 69-002072-00 69-003546-00
other than that you can... take an T1/PRI card, install daughtercard (E1) from ..2072-00 NAC and flash T1 DSP for E1 and that works.
At 04:08 AM 9/29/2005, you wrote:
Thu, Sep 29, 2005 at 10:59:24AM +0300, Teodor Georgiev wrote:
I got a good deal on some refurbished Hiper DSP cards. The issue is - the guy says they work on T1. Unfortunately E1 is my only choice. What gives me some hope is that on the back of the chassis one can see the sign "Hiper DSP T1/E1 NIC". Also, some voice gateways (like Quintum) can switch the port from T1 to E1 (and vice versa) only by changing a simple settings inside them.
So, my main question is - can I upload an E1 firmware (R2 CAS) into the Hiper DSP card with the idea to switch it from T1 to E1 ?
It depends entirely on the generation of the card. The most common answer is no, you can't. I went through the same thing before. Bascially, contact Commworks and give them the part number of your NAC cards and ask if they are able to be firmware flashed with E1 code. Only newer NACs supported both E1 and T1 firmware.
Patrick
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
the nac pn# should be one of the 2 listed if its a true E1 NAC. (1) 69-002072-00 carries a daughtercard that give the 30 channel function Its this daughtercard that you can install on older T1 DSP card. Has to have daughtercard connection on DSP NAC board. Then send E1 firmware upload. (2) 69-003546-00 newer version no daughtercard or connection on board. What cards do you have? At 11:12 PM 9/29/2005, you wrote:
Hi, do you mean these are the PN# i should look for that if I want to flash a T1 to E1? Where can I get the flash software, can u help me? thanks
Richard
NAC PN# for E1 should be...
other than that you can... take an T1/PRI card, install daughtercard (E1) from ..2072-00 NAC and flash T1 DSP for E1 and that works.
At 04:08 AM 9/29/2005, you wrote:
Thu, Sep 29, 2005 at 10:59:24AM +0300, Teodor Georgiev wrote:
I got a good deal on some refurbished Hiper DSP cards. The issue is - the guy says they work on T1. Unfortunately E1 is my only choice. What gives me some hope is that on the back of the chassis one can see the sign "Hiper DSP T1/E1 NIC". Also, some voice gateways (like Quintum) can switch the port from T1 to E1 (and vice versa) only by changing a simple settings inside them.
So, my main question is - can I upload an E1 firmware (R2 CAS) into the Hiper DSP card with the idea to switch it from T1 to E1 ?
It depends entirely on the generation of the card. The most common answer is no, you can't. I went through the same thing before. Bascially, contact Commworks and give them the part number of your NAC cards and ask if they are able to be firmware flashed with E1 code. Only newer NACs supported both E1 and T1 firmware.
Patrick
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
Pretty sure I have a bunch of these: (2) 69-003546-00 newer version no daughtercard or connection on board Shannan sky1@airmail.net www.swdt.com Southwest Data Technology, Inc. 860 N. Dorothy Drive Suite #608 Richardson, TX 75081 972-739-7010 972-739-7013 (Fax) THE INFORMATION CONTAINED IN THIS MESSAGE AND ANY ATTACHMENT MAY BE PRIVILEGED, CONFIDENTIAL, PROPRIETARY OR OTHERWISE PROTECTED FROM DISCLOSURE. If the reader of this message is not the intended recipient, you are hereby notified that any dissemination, distribution, copying or use of this message and any attachment is strictly prohibited. If you have received this message in error, please notify us immediately by replying to the message and permanently delete it from your computer and destroy any printout thereof. ----- Original Message ----- From: "Steve Rivera - WRCA.Net" <steverivera@wrca.net> To: "Discussion relating to the 3Com/US Robotics Total Control modem systems." <usr-tc@mailman.xmission.com> Sent: Friday, September 30, 2005 10:46 AM Subject: Re: [USR-TC] Hiper DSP T1 / E1 cards ?
the nac pn# should be one of the 2 listed if its a true E1 NAC. (1) 69-002072-00 carries a daughtercard that give the 30 channel function Its this daughtercard that you can install on older T1 DSP card. Has to have daughtercard connection on DSP NAC board. Then send E1 firmware upload.
(2) 69-003546-00 newer version no daughtercard or connection on board.
What cards do you have?
At 11:12 PM 9/29/2005, you wrote:
Hi, do you mean these are the PN# i should look for that if I want to flash a T1 to E1? Where can I get the flash software, can u help me? thanks
Richard
NAC PN# for E1 should be...
other than that you can... take an T1/PRI card, install daughtercard (E1) from ..2072-00 NAC and flash T1 DSP for E1 and that works.
At 04:08 AM 9/29/2005, you wrote:
Thu, Sep 29, 2005 at 10:59:24AM +0300, Teodor Georgiev wrote:
I got a good deal on some refurbished Hiper DSP cards. The issue is - the guy says they work on T1. Unfortunately E1 is my only choice. What gives me some hope is that on the back of the chassis one can see the sign "Hiper DSP T1/E1 NIC". Also, some voice gateways (like Quintum) can switch the port from T1 to E1 (and vice versa) only by changing a simple settings inside them.
So, my main question is - can I upload an E1 firmware (R2 CAS) into the Hiper DSP card with the idea to switch it from T1 to E1 ?
It depends entirely on the generation of the card. The most common answer is no, you can't. I went through the same thing before. Bascially, contact Commworks and give them the part number of your NAC cards and ask if they are able to be firmware flashed with E1 code. Only newer NACs supported both E1 and T1 firmware.
Patrick
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
You have to flash the HiperDSP cards with the appropriate firmware. But bear in mind that for an E1 you have two possibilities: R2 (CAS) or ISDN PRI. The firmware images for each of those is a separate one. So, please tell me if you are going to use the Hiper DSP with E1/R2 or E1/ISDN PRI and I will see what is the firmware code I have at my archives. Indeed, R2 is a ancient signalling protocol being still used only in "third-world" countries like Middle East, Africa, Asia... --- Shannan Young <sky1@airmail.net> wrote:
Pretty sure I have a bunch of these: (2) 69-003546-00 newer version no daughtercard or connection on board Shannan sky1@airmail.net www.swdt.com Southwest Data Technology, Inc. 860 N. Dorothy Drive Suite #608 Richardson, TX 75081 972-739-7010 972-739-7013 (Fax)
THE INFOssRMATION CONTAINED IN THIS MESSAGE AND ANY ATTACHMENT MAY BE PRIVILEGED, CONFIDENTIAL, PROPRIETARY OR OTHERWISE PROTECTED FROM DISCLOSURE. If the reader of this message is not the intended recipient, you are hereby notified that any dissemination, distribution, copying or use of this message and any attachment is strictly prohibited. If you have received this message in error, please notify us immediately by replying to the message and permanently delete it from your computer and destroy any printout thereof.
----- Original Message ----- From: "Steve Rivera - WRCA.Net" <steverivera@wrca.net> To: "Discussion relating to the 3Com/US Robotics Total Control modem systems." <usr-tc@mailman.xmission.com> Sent: Friday, September 30, 2005 10:46 AM Subject: Re: [USR-TC] Hiper DSP T1 / E1 cards ?
the nac pn# should be one of the 2 listed if its a true E1 NAC. (1) 69-002072-00 carries a daughtercard that give the 30 channel function Its this daughtercard that you can install on older T1 DSP card. Has to have daughtercard connection on DSP NAC board. Then send E1 firmware upload.
(2) 69-003546-00 newer version no daughtercard or connection on board.
What cards do you have?
At 11:12 PM 9/29/2005, you wrote:
Hi, do you mean these are the PN# i should look for that if I want to flash a T1 to E1? Where can I get the flash software, can u help me? thanks
Richard
NAC PN# for E1 should be...
other than that you can... take an T1/PRI card, install daughtercard (E1) from ..2072-00 NAC and flash T1 DSP for E1 and that works.
At 04:08 AM 9/29/2005, you wrote:
Thu, Sep 29, 2005 at 10:59:24AM +0300, Teodor Georgiev wrote:
I got a good deal on some refurbished Hiper DSP cards. The issue is - the guy says they work on T1. Unfortunately E1 is my only choice. What gives me some hope is that on the back of the chassis one can see the sign "Hiper DSP T1/E1 NIC". Also, some voice gateways (like Quintum) can switch the port from T1 to E1 (and vice versa) only by changing a simple settings inside them.
So, my main question is - can I upload an E1 firmware (R2 CAS) into the Hiper DSP card with the idea to switch it from T1 to E1 ?
It depends entirely on the generation of the card. The most common answer is no, you can't. I went through the same thing before. Bascially, contact Commworks and give them the part number of your NAC cards and ask if they are able to be firmware flashed with E1 code. Only newer NACs supported both E1 and T1 firmware.
Patrick
__________________________________ Yahoo! Mail - PC Magazine Editors' Choice 2005 http://mail.yahoo.com
participants (6)
-
Patrick Cole -
Richard S. Dy -
Shannan Young -
Steve Rivera - WRCA.Net -
Teodor Georgiev -
Teodor Georgiev