Last Friday I posted a message to the list (it never showed up though) about a problem we saw with the TCH. Turns out the "Chassis Awareness" for the NMC was disabled. This happened Thursday night at 10:00pm. I took me a while to figure out what was wrong since everything else checked out OK. I did have a 2nd HARC installed, but not active. I was looking at the 'show nmc settings' command and noticed that the Chassis Awareness was disabled and remembered from my notes that it should be enabled. Issuing the command, 'enable nmc chassis_awareness' did nothing, but once I pulled the 2nd HARC out and issued the command again it accepted it and suddenly the system started taking calls again. What would cause the NMC to loose or have this setting disabled? Other than a malicious person changing it, but the system is protected with a good password and there was nothing in the logs to indicate that happened. - Mike ------------------------------------------------ Rock Island Communications, Inc. (360)-378-5884 http://www.rockisland.com/ San Juan Islands, WA ------------------------------------------------ - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Chassis awarness is enabled by default. You would have to disable it else its always on. Once you enable "Chassis Awarness" it does not do anything immediately, it waits for the next NMC update, once that update is got, depending of if you have DSA and Rebalancing enabled, you will have some type of changes in the arc ownership. Once you pull out a card from the chassis, the NMC takes notice and sends the chassis awarness message, thus cauing the other arc to own the DSP currently owned by the ARC that was removed. Most likely you had the NMC chassis awarness disabled to start with. -V ----- Original Message ----- From: "Mike Greene" <mikeg@rockisland.com> To: <usr-tc@lists.xmission.com> Sent: Sunday, July 08, 2001 2:41 PM Subject: (usr-tc) Chassis Awareness?
Last Friday I posted a message to the list (it never showed up though) about a problem we saw with the TCH.
Turns out the "Chassis Awareness" for the NMC was disabled. This happened Thursday night at 10:00pm. I took me a while to figure out what was wrong since everything else checked out OK.
I did have a 2nd HARC installed, but not active. I was looking at the 'show nmc settings' command and noticed that the Chassis Awareness was disabled and remembered from my notes that it should be enabled. Issuing the command, 'enable nmc chassis_awareness' did nothing, but once I pulled the 2nd HARC out and issued the command again it accepted it and suddenly the system started taking calls again.
What would cause the NMC to loose or have this setting disabled? Other than a malicious person changing it, but the system is protected with a good password and there was nothing in the logs to indicate that happened.
- Mike
------------------------------------------------ Rock Island Communications, Inc. (360)-378-5884 http://www.rockisland.com/ San Juan Islands, WA ------------------------------------------------
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
At 09:31 PM 7/8/01 -0500, you wrote:
Most likely you had the NMC chassis awarness disabled to start with.
That wasn't the case though, a while back I was emailing with Jeff McAdams about setting up the 2nd ARC and I did a screen shot of the settings and included that in my email, it was enabled at that time and I had not made any configuration changes since then either. Sounds like a glitch or something, I never did finish setting up the 2nd ARC so I just pulled it out for now. - Mike ------------------------------------------------ Rock Island Communications, Inc. (360)-378-5884 http://www.rockisland.com/ San Juan Islands, WA ------------------------------------------------ - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
Hi, excusme my english i have this problem , with hiper dsp , i have configuration it with e1 /r2 and i need get the ani number , i do the next procedure by my total contro manager , in the dsp card trunk settings in the option dial in address i check ani (also dnis and ani-dnis) but when i look register by one administation web page don´t show it , I speak with telco and say that they send the code . thanks - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
participants (3)
-
Mike Greene -
Ved -
Wilson Diaz