You'll also have to make sure your router is listening to ripv2 routing updates. On Friday, October 01, 1999 10:05 AM, Jim Johnson [SMTP:jim@perigee.net] wrote:
set ip network ip2 routing_protocol ripv2
Robb Bryn wrote:
I've disabled IP SOURCE_ADDRESS_FILTER allready (no luck). How do I
turn
on RIPv2 on the arc?
Thanks Robb Bryn
-----Original Message----- From: owner-usr-tc@lists.xmission.com [mailto:owner-usr-tc@lists.xmission.com]On Behalf Of Stainforth, Matthew Sent: Friday, October 01, 1999 8:25 AM To: 'usr-tc@lists.xmission.com' Subject: RE: (usr-tc) TCHub and routing
I believe you'll also want to build static routes or have the ARC advertise the subnet using OSPF or RIPv2 if you want that subnet to be reachable from anywhere other than the ARC itself.
Matthew
On Friday, October 01, 1999 9:00 AM, Jim Johnson [SMTP:jim@perigee.net] wrote:
Make sure you:
DISABLE IP SOURCE_ADDRESS_FILTER
if you want the routing to actually **work** as opposed to just **showing up** in the routing table correctly.
-Jim
Robb Bryn wrote:
I'm configuring my first routed subnet on the TCHub and
can't quite
figure out what I'm doing wrong.
I have a Ascend P50 dialing in via ISDN with radius attributes of: Framed-Address = 208.150.95.241 Framed-Route = 208.150.95.240/29 208.150.95.241 1
After connecting, I can ping the ether address of the TCHub (208.133.28.51) from any of the subnet hosts can't ping anything past it. I can't ping any host on the subnet from the TCHub. Below is the output from the show ip network command.
HiPer>> show ip network test-ip-I4586
SHOW IP NETWORK test-ip-I4586 SETTINGS: Interface: slot:14/mod:2 Network Address: 208.150.95.241/H Frame Type: PPP Status: ENABLED Reconfigure Needed: FALSE Mask: 255.255.255.255 Station: 0.0.0.0 Broadcast Algorithm: IETF Max Reassembly Size: 3464 IP Routing Protocol: NONE IP Routing Metric: 1 RIP Interface Export Metric: 0 IP RIP Routing Policies: IP RIP Authentication Key: HiPer>>
I'm pulling my hair out trying to figure out what I've done wrong. A kick in the right direction would be greatly appreciated.
Thanks,
Robb Bryn
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.