On Dec 21, 11:21am, Jim Johnson wrote:
Subject: Re: (usr-tc) DMS-500 and NI-2 Problems
We are setting up a new POP and ran into that same problem initially.
I'll bet if you use TCM and issue the command "Local In Service" to the PRI card, the calls will start coming in.
There is a setting in the DMS-500 switch to "emulate" an AT&T switch. This will cause the D-Channels to come up properly when you reset the card. The phone company needs to set this for you.
I hate switching telcos...
Thanks for the pointer. I went ahead and issued Local In Service, with and without Service Messages, in TCM and in command line on the DSP and I am still having issues, but that sort of makes sense since NI-2 does not support service messages. I have emailed the telco to have them set up the emulation though (or try to have them do it.) With this emulation in place, are you still using NI-2 or can you then set things up to use an AT&T 5ess? Thanks again!
Regards,
Jim
"G. Douglas Davidson" wrote:
We are in the process of setting up some new PRIs and things ain't going so well. We have to use the NI-2 interface, as it seems to be the only one supported by the CLEC. Everything looks just swell on this side, yet we
are
getting "all circuits busy" when we attempt to use the lines.
Turned off service messaging as per one of the list suggestions. Running DSP 2.1.9. D-Channel is up. Things look good.
Thanks for any suggestions.
span1> dis atstat
Tslot Status Modem Status Call ID Action Q931 Connect Srvc State Queued Ref 01 Idle N/A IS 0x00000000 NONE 0x00000000 ... 23 Idle N/A IS 0x00000000 NONE 0x00000000 24 Dchan N/A IS 0x00000000 NONE 0x00000000
span1> dis ccrcfig Span1 Configured Signal Mode is (sigmode): MESSAGE ORIENTED Span1 Signal Mode Active is: MESSAGE ORIENTED Span1 DNIS Enable is (dnisena): DNIS ADDRESS Span1 Dial Out Address Delay (doadrdly): 70 ms Span1 Configured Switch Type is (swtype): NI2 Span1 Idle Byte is (idlebyte): 0xFE Span1 Ana Calls Blocked Err Code (ancbec): 58 Span1 Digi Calls Blocked Err Code (dcbec): 58 Span1 No IGWS Avail Err Code (noigwsav): 58 Span1 Chan Blocked Err Code (chanblck): 58 Span1 Block Call Type is (blcaltyp): BLOCK NONE Span1 Tone Type is (tonetype): DTMF TONE Span1 Number Of DTMF Tones is (numdtmft): 4 Span1 Dial Out Select Direction (dseldir): DOWN Span1 Dial Out Next Timeslot (dntslot): 24 Span1 Alert Message Mode (alrtmsg): ALRT MSG MODE DISABLED Span1 CALL PROC Message Mode (cprocmsg): CALLPROC MSG MODE ENABLED Span1 Overlap Receiving Mode (ovrrxmode): OVERLAP RECEIVE MODE DISABLED Span1 Timeout between INFO msg(inftmout): 12 Span1 Total Number of Digits (inbdnisln): 12 Span1 Signaling Group Type is: FAS Span1 Configured SS7 signal mode is: None Span1 active SS7 signal mode is: None
span1> dis spnstats Span1 Near Time Elapsed is: 653 seconds Span1 Near Valid Intervals is: 69 Span1 Line Status is: NO ALARM = TRUE RCV FAR END LOF = FALSE XMT FAR END LOF = FALSE RCV AIS = FALSE XMT AIS = FALSE OUT OF FRAME = FALSE LOSS OF SIGNAL = FALSE LOOPBACK STATE = FALSE T16 AIS = FALSE RCV FAR END LOMF = FALSE XMT FAR END LOMF = FALSE RCV TEST CODE = FALSE OTHER FAILURE = FALSE Span1 Send Code is: SEND NO CODE Span1 dsx1 Loopback Configuration is: NO LOOP Span1 Receiver Gain is: 0.0 dB GAIN (2.9 dB Steps) Span1 Continuous CRC Error is: FALSE Span1 Physical State is: F1 OPERATIONAL Span1 Loopback Init Originate is: NONE Span1 Modem Not Available Count is: 0 Span1 Invalid Bearer Capability Count is: 0 Span1 Invalid Channel ID Count is: 0 Span1 Invalid Progress Indicator Count is: 0 Span1 Invalid Calling Party Count is: 0 Span1 Invalid Called Party Count is: 0 Span1 Call Block Failure Count is: 0 Span1 No Ring Off Failure Count is: 0 Span1 Telco Disconnect Failure Count is: 0 Span1 TELCO Failed To Wink Count is: 0 Span1 TELCO Wink Too Short Count is: 0 Span1 No Channel Available Count is: 0 Span1 Dial In No Resp To Disc Count is: 0 Span1 Dial Out No Resp To Disc Count is: 0 Span1 Gnd Start No Resp To Disc Count is: 0 Span1 Switch Type Active is: NI2 Span1 D-channel Operational is: UP Span1 Signal Mode Active is: MESSAGE ORIENTED Span1 Service Messages Sent: 0 Span1 Service Ack Messages Received: 0
-- ----- G Douglas Davidson | CityNet, Inc. douglas@city-net.com | Pittsburgh, PA voice: 412.481.5406 | fax: 412.431.1315
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message. -- End of excerpt from Jim Johnson
-- ----- G Douglas Davidson | CityNet, Inc. douglas@city-net.com | Pittsburgh, PA voice: 412.481.5406 | fax: 412.431.1315 - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.