looks like i definitely need to call them first thing tomorrow and have them review the 11th pri and make sure it is identical to the first 10. matthew ---- Original Message ---- From: jcoombs@gwi.net To: usr-tc@mailman.xmission.com Subject: Re: [USR-TC] need help! hiper dsp/pri keeps going to Date: Tue, 8 Apr 2003 22:03:15 -0400
Also see if the the telco supports service messaging. We've had instances where b's would be dropped due to our end having service messaging enabled, and the remote ignoring it.
Joshua Coombs
On Tue, Apr 08, 2003 at 09:58:01PM -0400, Paul Farber wrote:
Biggest one will be Switch type.
Some switch type are 'close' - 5ESS and NI2 are ones that I had problems with. The switch type was NI2 but my DSPs were at 5ESS... worked for a while but would drop B's, go remote out of service and other errors.
Verify your line coding and switch type with telco... have them fax it to you if they can so if it changes you can show them.
-- Paul Farber Farber Technology farber@admin.f-tech.net Ph 570-628-5303 Fax 570-628-5545
On Tue, 8 Apr 2003 matthew@the-spa.com wrote:
i did load all the settings from the first hiper dsp in that
chassis.
i have to call the telco tomorrow and have them review all of
their
settings just in case that might be it.
thanks
matthew
---- Original Message ---- From: berto@voyager.net To: usr-tc@mailman.xmission.com Subject: RE: [USR-TC] need help! hiper dsp/pri keeps going to "remote out ofservice" after a bunch of calls Date: Tue, 8 Apr 2003 21:43:18 -0400
Maybe have the telco confirm the new PRI is setup exactly the same as the rest of them....assuming you checked ALL the config settings to confirm they are the same. Best bet would be to just load all the settings from one of the other dsps...you can do that from tcm.
Todd
-----Original Message----- From: usr-tc-bounces@mailman.xmission.com [mailto:usr-tc-bounces@mailman.xmission.com]On Behalf Of matthew Sent: Tuesday, April 08, 2003 9:44 PM To: usr-tc@mailman.xmission.com Subject: [USR-TC] need help! hiper dsp/pri keeps going to "remote out of service" after a bunch of calls
ok here is the situation...
i have a chassis with 11 hiper dsp's active, dual hiper arc's and a hiper nmc and dual 130's
i had 10 pri's running fine for the last two months.
added the 11th pri yesterday. it seems to run fine for a few hours, fills up with callers etc.
then it will get less "busy" than the rest of them, until it has nobody on it.
when i check it all of the channels are remote out of service.
if i do a hardware reset it goes back to normal for a few hours and then it does it all over again.
i have checked all of a the settings and i can't figure out what is wrong.
it seems to be identical to the other 10 pri's/hiper dsp's
same version etc.
can someone help me please?
thanks
matthew
matthew de Jongh president the spa! internet voice (413) 539-9818 www.the-spa.com
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc