No Problem...I've been through it all as far as trying to "bring back the dead" hardware. Todd ----- Original Message ----- From: "Joel - Fox Computers" <jfox@foxcomputers.com> To: <usr-tc@mailman.xmission.com> Sent: Monday, January 13, 2003 12:47 PM Subject: RE: [USR-TC] HiperNMC Dead?
Todd,
I owe you a big one - pulled that jumper and it booted up perfectly.
Thanks!
Joel
-----Original Message----- From: Todd Bertolozzi [mailto:berto@voyager.net] Sent: Monday, January 13, 2003 6:00 AM To: usr-tc@mailman.xmission.com Subject: Re: [USR-TC] HiperNMC Dead?
I'm thinking a reload through console might be your best option. Also...once in a while I've been able to get them to come back to life by removing the jumper from the bottom right of the NAC by TX,RX,GND. I found that documented in Commworks.
Todd ----- Original Message ----- From: "Joel - Fox Computers" <jfox@foxcomputers.com> To: <usr-tc@mailman.xmission.com> Sent: Friday, January 10, 2003 7:39 PM Subject: [USR-TC] HiperNMC Dead?
All of a sudden today, my HiperNMC disappeared from my network. Plugged a terminal into it's console port and got no response. Removed and plugged the card back in. Below is what I see. Anyone have any ideas what's wrong here? Did the card just die, or do I need to reflash the code onto it? I'm out of ideas on this one, never seen it before.
You'll notice at the bottom it says "press any key within 5 seconds". I tried that. it asked me for it's IP address, SN Mask, and Default Gateway and Startup Mode. I entered them and waited. It just sat there.
It says SDL2 Revision: 1.0.05. Does that mean that's the code version it's running? Has it lost it's programming and just needs a reload through the console port? Dunno what to do here.
Thanks,
Joel
3Com
SDL2 Revision: 1.0.05
BIOS Extension Link Date Aug 25 1998 at 14:13:08
Initiating Op
Equipment List Detected: ******************************************************************* * Platform: Hiper NMC * Flash Amount: 8M * DRAM Amount: 16M * * Chassis: 16-slot * NIC Type: Ethernet * Clocked Chassis * * PSU 1: INSTALLED * 130 Amps * AC Type * * PSU 2: INSTALLED * 130 Amps * AC Type * * Packet Bus Clock Circuit: Installed * * *******************************************************************
Power on Self Test in Progress...................................... ..............................TIMEOUT
** NMC Diagnostics Version 1.3.1. ** Manufacturing Code = 1AAA13M01234 Hardware ID = 0 Detected NMC platform. Test Name Time Status ----------------------------------------+------+-------- DRAM Test ------------------------------- () - PASSED Fan Speed Test -------------------------- () - PASSED Debug Port Test ------------------------- () - ERROR
Manufacturing Info -> 1AAA13M0 Mode/Env -> 1/0 Fault Code -> 0-6-1-1 Expected Data -> 0 Received Data -> 2710 Address of Failure -> 0 Text Message -> Debug Port Receiver Timeout Error
Real Time Clock Test -------------------- () - PASSED A to D Test ----------------------------- () - PASSED Ethernet NIC (Basic) Test --------------- () - PASSED Always Pass Test ------------------------ () - PASSED NMC Diagnostics Complete
pSOSystem V2.2.6 Copyright (c) 1991 - 1997, Integrated Systems,Inc.
--------------------------------------------------------------------------
START-UP MODE: Run the NMC NETWORK INTERFACE PARAMETERS: IP address on LAN is LAN interface's subnet mask is 0xffffff00 IP address of default gateway to other networks is HARDWARE PARAMETERS: 3-pin debug channel will use a baud rate of 9600 After board is reset, start-up code will wait 5 seconds
--------------------------------------------------------------------------
To change any of this, press any key within 5 seconds Updating parameter storage. This may take a while...Done
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc