Hard to tell....sometimes it's a pain getting in sync with the telco so to speak. Again...which telco provider is this...I might have some experience setting stuff up on their networks. Seems a little strange that your dsp's are statically assigned and the arc is dynamically assigned. I would stick with 1 way or the other. At this point I would probably let nmc chassis awarness do it's thing and dynamically find all the cards. You will probably have to reboot the arc or nmc (forget which) for the cards to be discovered properly. Todd ----- Original Message ----- From: "Carl Duescher" <carld@ez-net.com> To: "Discussion relating to the 3Com/US Robotics Total Control modem systems." <usr-tc@mailman.xmission.com> Sent: Tuesday, January 06, 2004 11:20 AM Subject: Re: [USR-TC] Problems getting DSP's to "Answer"
No I just didn't setup the HiperDSP in that slot so it is still setup as a PRI, it isn't in service just a spare.
On Tue, 6 Jan 2004, Todd Bertolozzi wrote:
Date: Tue, 6 Jan 2004 11:18:49 -0500 From: Todd Bertolozzi <todd.bertolozzi@voyager.net> Reply-To: Discussion relating to the 3Com/US Robotics Total Control modem systems. <usr-tc@mailman.xmission.com> To: Discussion relating to the 3Com/US Robotics Total Control modemsystems. <usr-tc@mailman.xmission.com> Subject: Re: [USR-TC] Problems getting DSP's to "Answer"
So do you have a PRI in slot 8 and channelized T1's in slots 9-14?
Todd ----- Original Message ----- From: "Carl Duescher" <carld@ez-net.com> To: "Discussion relating to the 3Com/US Robotics Total Control modem systems." <usr-tc@mailman.xmission.com> Sent: Tuesday, January 06, 2004 11:09 AM Subject: Re: [USR-TC] Problems getting DSP's to "Answer"
Here it is :). However it will answer as it should if the telco sets their switch to send digits and I enable the ack on address info receipt on the TC box...just seems odd to me that it would be required.
Slot Owner Description Ports Type Console 1 YES --EMPTY-- 0 STATIC NO 2 YES --EMPTY-- 0 STATIC NO 3 YES --EMPTY-- 0 STATIC NO 4 YES --EMPTY-- 0 STATIC NO 5 YES --EMPTY-- 0 STATIC NO 6 YES --EMPTY-- 0 STATIC NO 7 YES --EMPTY-- 0 STATIC NO 8 YES 24 Channel High Density Modem 23 STATIC YES 9 YES 24 Channel High Density Modem 24 STATIC YES 10 YES 24 Channel High Density Modem 24 STATIC YES 11 YES 24 Channel High Density Modem 24 STATIC YES 12 YES 24 Channel High Density Modem 24 STATIC YES 13 YES 24 Channel High Density Modem 24 STATIC YES 14 YES 24 Channel High Density Modem 24 STATIC YES 15 YES --EMPTY-- 0 STATIC NO 16 YES HiPer Access Router NAC 0 DYNAMIC NO
Carl Duescher EZ-Net Staff "Do or do not, there is no try." -Yoda, Jedi Master
On Tue, 6 Jan 2004, Lewis Bergman wrote:
Date: Tue, 6 Jan 2004 10:06:54 -0600 From: Lewis Bergman <lbergman@wtxs.net> Reply-To: Discussion relating to the 3Com/US Robotics Total Control modem systems. <usr-tc@mailman.xmission.com> To: Discussion relating to the 3Com/US Robotics Total Control modem systems. <usr-tc@mailman.xmission.com> Subject: Re: [USR-TC] Problems getting DSP's to "Answer"
On Tuesday 06 January 2004 09:10 am, Carl Duescher wrote:
Do you mean does the ARC own the DSP slots? Could you do a list chassis for us anyway? The only reason I say that is dead air is a classic symptom of a properly configed DSP that isn't owned by an ARC. If list chassis shows correct have you done a save all and rebooted?
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc
<!DSPAM:3ffadf64260151561313756>
_______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc