Hello Again: Vinny: I tried your suggestion. Still no progress. Same Error. Anybody else has a suggestion??? Thanks in advance. Kirt -----Original Message----- From: Vincent Jordan [mailto:vjordan@cyberspeed-data.com] Sent: Monday, August 25, 2003 4:53 PM To: 'Discussion relating to the 3Com/US Robotics Total Control modemsystems.' Subject: RE: [USR-TC] Total Control manager Do the following: Console into the NMC with hyper terminal Press 1 configuration Press 8 reinitialize authorize access list The try to open with the TCM Hope this helps Vinny -----Original Message----- From: usr-tc-bounces@mailman.xmission.com [mailto:usr-tc-bounces@mailman.xmission.com] On Behalf Of Kirti S. Bajwa Sent: Monday, August 25, 2003 4:40 PM To: 'alex'; Kirti S. Bajwa; 'support@isn.net'; 'usr-tc@mailman.xmission.com' Subject: RE: [USR-TC] Total Control manager Hello Alex & ??: I have followed both of your advice, by performing the following steps (O/S is Win NT 4.?): 1. Setup HiPer NMC (Hyper Terminal) . Setup IP address (63.113.255.9) . Setup Netmask (255.255.255.0) . Setup Gateway Address (63.113.255.1 => I assume this is the IP address of my CISCO 26?? Router) . Change Community Settings (tibp for Public & tibr for Private) . Save in NVRAM . Reset Hiper NMC 2. Run TCM . Open a new chassis under name TIB-TC1 . Target Host 63.113.255.9 . SMTP Community Setting a. Read Only: tibp b. Read+Write: tibr c. OK I have done it half a dozen time and receive the same error message: TIB-TC1 Device not responding Refer to the troubleshooting section of the user guide For your information, I can PING the NMC & Gateway ( 63.113.255.9 & 63.113.255.1 )!!! Do you think that Win NT 4.? May be the problem? HELP.. I am going crazy!! Kirt -----Original Message----- From: alex [mailto:alex@wanex.ge] Sent: Monday, August 25, 2003 4:08 PM To: kbajwa@tib.com Subject: Re: [USR-TC] Total Control manager Set up NMC card: put IP address and netmask, gateway address. Change commuity strings. Then connect NMC to LAN. Run TCM. Open a new chassis (or smth. like this), write NMCs IP address and read/write community strings. Thats all. ----- Original Message ----- From: Kirti S. Bajwa To: 'usr-tc@mailman.xmission.com' Sent: Monday, August 25, 2003 3:20 AM Subject: [USR-TC] Total Control manager Hello List: My question will prove that I am below being NOVICE regarding 3Com TC. I have read about 10-12 different documents. I can connect and configure various cards on the 3Com TC box using a serial connection to a Win NT PC. My problem is that I have not been able to figure out how to start the "Total Control Manager for Windows" application? Can somebody direct me to a document or explain how I can launch TCM? Thanks. Kirt Bajwa TIB Computer Systems Mountain City, TN 37683 Tel: (423) 727-3001 eMail: kbajwa@tib.com _______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC@mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc