Sorry Brian, I haven't found the HARC's debug of multicast very good at all - it looks like you have covered all the options for the dial-in user - you may even have too much enabled....
-----Original Message----- From: Brian [SMTP:signal@shreve.net] Sent: Tuesday, August 29, 2000 2:13 PM To: Vance McIndoe Cc: 'usr-tc@lists.xmission.com' Subject: RE: (usr-tc) Multicast
On Tue, 29 Aug 2000, Vance McIndoe wrote:
Brian,
I think you'll find that the RADIUS attributes, when set, cause changes to the user's modem interface. You can probably use set modem_group all ...... and then do a, save all, to set the same options globally. Remember this wort of change will be visible to the astute dial-in customer though :-)
vance,
I think just setting the defaults like you show below does the trick. I can observe:
HiPer>> show ip igmp slot:9/mod:17 slot:9/mod:17 Query Interval 125 seconds Max Response 10 seconds Version 2 Querier 208.206.76.40 Joins 1 Groups 1 Robustness 2 Routing ENABLED Multicast Forwarding ENABLED Multicast Proxy ENABLED IGMP Short Packets 0 IGMP Bad Checksum 0 Queries Received 0 Reports Received 0 Reports For Known Groups Received 0 Wrong Version Reports Received 0 Reports Sent 0
I am dialing in with a pipeline p50. I set multicast forwarding on on it. But on my linux box behind the pipeline I can't mtrace anything, and SDR shows nothing. I see the packets going out (the box is configured correct for multicast because if I connect it on the lan where the total control is, it works fine: mtrace, sdr, etc)
Any ideas? I just want to make sure that multicast is working thru the total control, I would have thought I could mtrace thru the connection.
Brian
Vance
-----Original Message----- From: Brian [SMTP:signal@shreve.net] Sent: Tuesday, August 29, 2000 11:49 AM To: usr-tc@lists.xmission.com Cc: usr-tc@xmission.com Subject: Re: (usr-tc) Multicast
if a user is configured via radius with no multicast radius options,
but
the ARC has the commands below configured, will that user be able to receive multicast?
I can add the 5 lines to my ARC's, but don't want to have to add 3 lines to every users radius profile if I don't have too.
At first look it doesn't appear to be working. Is there a "show" or "list" command that will tell me that mutlicast is enabled for a user?
I am trying this dialed in, and trying to run SDR but get nothing. I am using a pipeline which has multicast enabled on it (perhaps the ARC does not build or forward an SDR cache information?)
Brian
On Tue, 25 Jul 2000, Antonio Querubin wrote:
On Tue, 25 Jul 2000, Steve Johnson wrote:
I have a USR/3Com Totalcontrol NAS with PRI/T1 cards in it. Does anyone know if these support multicast by default, and if not can someone point me the direction of some documentation on how to turn this on?
You'll need a HiPer ARC router card installed in the chassis to do multicast. The Netserver router card has no multicast capability. Multicast is disabled by default on the HiPer ARC. To turn it on you do something like:
set ip multicast proxy interface eth:1 set ip igmp eth:1 multicast_forwarding enabled set network user default igmp multicast_forwarding enabled set network user default igmp multicast_proxy enabled set network user default igmp routing enabled
This seems to work for users wishing to receive multicast via dialup. I haven't yet tested whether this also allows users to source multicast via dialup.
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
----------------------------------------------- Brian Feeny, CCNA, CCDA signal@shreve.net Network Administrator ShreveNet Inc. (ASN 11881)
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
______________________________________________________________ This email has been virus and policy checked by InterConnect Secure's Messaging Management System (MMS) product from Tumbleweed
Network ICE "Stop hackers cold!" Free download of Black ICE - see just who is interested your PC. http://www.interconnect.co.nz/Interconnect/secure/networkice.htm ______________________________________________________________
- To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.
----------------------------------------------- Brian Feeny, CCNA, CCDA signal@shreve.net Network Administrator ShreveNet Inc. (ASN 11881)
______________________________________________________________ This email has been virus and policy checked by InterConnect Secure's Messaging Management System (MMS) product from Tumbleweed Network ICE "Stop hackers cold!" Free download of Black ICE - see just who is interested your PC. http://www.interconnect.co.nz/Interconnect/secure/networkice.htm ______________________________________________________________ - To unsubscribe to usr-tc, send an email to "majordomo@xmission.com" with "unsubscribe usr-tc" in the body of the message. For information on digests or retrieving files and old messages send "help" to the same address. Do not use quotes in your message.