SaskTel (Saskatchewan, Canada) They havn't been much help - they've been very nice and tried, but it took them 5 minutes to look up ESF & B8ZS because they wern't familiar with those terms... Could this be NOT trunk settings and modem settings or ARC settings instead? On 9/5/02 10:45 AM, USR-TC@MAILMAN.XMISSION.COM wrote to SUPPORT: -> What telco? -> -> Todd -> -> -----Original Message----- -> From: usr-tc-admin@mailman.xmission.com -> [mailto:usr-tc-admin@mailman.xmission.com]On Behalf Of -> support@inet2000.com -> Sent: Thursday, September 05, 2002 12:29 PM -> To: usr-tc@mailman.xmission.com -> Subject: RE: [USR-TC] HELP: Lightning HiPerDSP -> -> -> Help. :-) Here are our current settings. We get a dead air answer. If -> anyone can suggest anything to try, please help. -> -> Frame Mode : ESF -> Line Code : B8ZS -> Circuit : -> Loopback : NoLoop -> SignalMode : robbedbit -> Xmitclock : loopTiming -> NicType : LongHaul -> Response : ignore -> JitterAten : attenJitterOnRcvr -> XmitBuild : dB0pt0 -> DialAddress : dnis -> DialTrStart : immediate -> AckWinkAddr : disabled -> DialOutDelay: 70 -> DialTrnkType: loopStart -> PrSwitchType: 5ESS -> IdleBytePtrn: 254 -> ReceiverGain: dB26 -> Tone Type : dtmf -> #ofDTMFTones: 4 -> Send Code : SendNoCode -> XternalSgMod: None -> OvrlpRecMode: disable -> OvrlpInbound: 12 -> OvrlpTimeout: 12 -> -> We're tried various settings for many items, including loop vs ground -> start - -> immediate vs wink start - # of DTMF tones, Switch Type, Nic Type.... -> -> We get the same results on two different DSP cards, yet the T1 works on our -> old backup equipment, so it must be OK. -> -> The LIST CHASSIS shows: -> 1 YES 24 Channel HDM 24 DYNAMIC YES -> 2 YES -- EMPTY -- 0 STATIC NO -> 3 YES 24 Channel HDM 24 DYNAMIC YES... -> -> LIST INT shows everything except eth:2 as UP & UP. eth:2 is Down & UP, but -> otherwise everthing else is UP & UP across the chassis. -> -> -> -> -> On 9/5/02 10:14 AM, USR-TC@MAILMAN.XMISSION.COM wrote to SUPPORT: -> -> -> That's not a test, it's a condition. Yellow means there is a loopback -> -> condition. So far all posts look correct regarding DNIS. If the Telco -> sends -> -> digits, set it to DNIS, and DTMF tones equal to the number of digits. If -> -> they are not, set it to "no address". This of course assumes your ARC -> OWNS -> -> the DSP. Do a List chassis" and make sure your ARC owns the DSP's in -> -> question. Then, do a "list Int" and makes sure your modem ports say up -> and -> -> up. If they are, then more than likely, this is a DNIS digit thing. -> -> -> -> Rick -> -> Team Solunet -> -> -> -> -----Original Message----- -> -> From: Support [mailto:support@inet2000.com] -> -> Sent: Thursday, September 05, 2002 11:06 AM -> -> To: usr-tc@mailman.xmission.com -> -> Subject: Re: [USR-TC] HELP: Lightning HiPerDSP -> -> -> -> -> -> It just stays Yellow forever? It would be nice if it blinked -> -> a couple times and then went off or something for a -> -> successful test. Mine goes Yellow no matter what I set -> -> it to pretty much, and it stays that way forever. -> -> -> -> ----- Original Message ----- -> -> From: "Lewis Bergman" <lbergman@abi.tconline.net> -> -> To: <usr-tc@mailman.xmission.com> -> -> Sent: Thursday, September 05, 2002 7:24 AM -> -> Subject: Re: [USR-TC] HELP: Lightning HiPerDSP -> -> -> -> -> -> > On Thursday 05 September 2002 12:04 am, Support wrote: -> -> > > Hi Lewis. I tried this with a LoopBack adapter that came with our -> -> Equinox -> -> > > Digital Modem Pools we used to have. When I initiate the Loopback -> test -> -> by -> -> > > setting the mode from NoLoop to Payload or Line, the LoopBack LED -> goes -> -> > > Yellow (test in progress) but it never comes back from yellow. Can -> you -> -> > > explain -> -> > > how the sequence should look? -> -> > That's what mine does when I put it on line loopback and put my adapter -> -> in. I -> -> > would have to go dig in the docs to see what a bad one does. -> -> > Try this page for some more troublrshooting help. -> -> > -- -> -> > Lewis Bergman -> -> > Texas Communications -> -> > 4309 Maple St. -> -> > Abilene, TX 79602-8044 -> -> > 915-695-6962 ext 115 -> -> > -> -> > _______________________________________________ -> -> > USR-TC mailing list -> -> > USR-TC@mailman.xmission.com -> -> > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc -> -> > -> -> -> -> -> -> _______________________________________________ -> -> USR-TC mailing list -> -> USR-TC@mailman.xmission.com -> -> http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc -> -> -> -> _______________________________________________ -> -> USR-TC mailing list -> -> USR-TC@mailman.xmission.com -> -> http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc -> -> -> -> -> _______________________________________________ -> USR-TC mailing list -> USR-TC@mailman.xmission.com -> http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc -> -> -> -> -> _______________________________________________ -> USR-TC mailing list -> USR-TC@mailman.xmission.com -> http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc