- USR-TC - mailman.xmission.com

RE: [USR-TC] Hiper Arc Problems Please Help
by RickL＠solunet.com 05 Dec '02

05 Dec '02

Ouch. So, you can make a change via telnet, do a "save all", then reboot, and your changes do not save (therefore the card does not work), but if you reboot the chassis, it comes up fine? -----Original Message----- From: Travis M. Best [mailto:sysadmin@sunqwest.net] Sent: Wednesday, December 04, 2002 7:02 PM To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] Hiper Arc Problems Please Help Rick, The Dip Switch Is Off -----Original Message----- From: usr-tc-admin(a)mailman.xmission.com [mailto:usr-tc-admin@mailman.xmission.com] On Behalf Of RickL(a)solunet.com Sent: Wednesday, December 04, 2002 5:22 PM To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] Hiper Arc Problems Please Help Is Dip switch # 5 on? (Component side near front edge of ARC). Rick Team Solunet -----Original Message----- From: Travis M. Best [mailto:sysadmin@sunqwest.net] Sent: Wednesday, December 04, 2002 12:46 PM To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] Hiper Arc Problems Please Help This I can do a software reboot on the DSP cards and have no problems it when I try a software reboot on the hiper arc card that causes the problem -----Original Message----- From: usr-tc-admin(a)mailman.xmission.com [mailto:usr-tc-admin@mailman.xmission.com] On Behalf Of RickL(a)solunet.com Sent: Wednesday, December 04, 2002 11:46 AM To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] Hiper Arc Problems Please Help Travis, When you reboot an individual card, the system loads the configuration from the local flash on the card. By contrast, each card will pull their configuration for the flash on the NMC when the system is powered down and brought back up. All you should have to do is reboot the chassis, then save all of your modems to their local flash when they come back up. Then you can reboot individual cards or the whole chassis without killing a thing. (choose card, "Configure", "Action Commands", Choose software, the "Save both T1/E1 and modems TO NVRAM") Hope this helps.. Rick Team Solunet -----Original Message----- From: Travis M. Best [mailto:sysadmin@sunqwest.net] Sent: Tuesday, December 03, 2002 9:09 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] Hiper Arc Problems Please Help I have a problem where if I reboot the chassie from the telnet window of do a software reset on the hiper arc it busy out my modems with a fast busy but if I power down the unit and power it backup everything is ok. Has anyone seen this before??? Is this some setting I am missing some where? Please help Thanks, Travis Best Systems Administrator

2 1

Re: [USR-TC] WTS: Spare TC1000 chassis w/power
by Mike Greene 05 Dec '02

05 Dec '02

Sorry list, that was supposed to go private.. - Mike ------------------------------------------------ Rock Island Communications, Inc. (360)-378-5884 http://www.rockisland.com/ San Juan Islands, WA ------------------------------------------------

1 0

WTS: Spare TC1000 chassis w/power
by sky1 05 Dec '02

05 Dec '02

I have a couple of extra Total Control chassis I'd like to get rid of. They are both the Newer "Blue" labeled chassis w/ dual 130Amp AC power and fan assembly. $475.00 each If you need 'em, let me know. Thanks, Shannan Young SouthWest Data Technology, Inc. 972-739-7010 972-739-7013 (Fax) sky1(a)airmail.net www.swdt.com

2 1

Re: [USR-TC] WTS: Loaded Hipeer DSP bundles $5500.00
by Greg Coffey 04 Dec '02

04 Dec '02

Sheesh, I remember when I paid Thirty Grand for a 48 quad modem TC box! They didn't support them any better in those days. I still ended up paying for a support contract separately to get the "free" upgrade to 56k x2. At 03:40 PM 12/4/2002 -0600, you wrote: >Do you still have any of these in stock? As I understand it, the bundle is >$5500 for 14 HiperDSP (t1), 2 HiperARC (128MB), 1 Hiper NMC, and a 3com >chassis with dual 130Amp AC power. Is this correct? > >-- >-Tim

3 3

RE: [USR-TC] Hiper Arc Problems Please Help
by RickL＠solunet.com 04 Dec '02

04 Dec '02

Is Dip switch # 5 on? (Component side near front edge of ARC). Rick Team Solunet -----Original Message----- From: Travis M. Best [mailto:sysadmin@sunqwest.net] Sent: Wednesday, December 04, 2002 12:46 PM To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] Hiper Arc Problems Please Help This I can do a software reboot on the DSP cards and have no problems it when I try a software reboot on the hiper arc card that causes the problem -----Original Message----- From: usr-tc-admin(a)mailman.xmission.com [mailto:usr-tc-admin@mailman.xmission.com] On Behalf Of RickL(a)solunet.com Sent: Wednesday, December 04, 2002 11:46 AM To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] Hiper Arc Problems Please Help Travis, When you reboot an individual card, the system loads the configuration from the local flash on the card. By contrast, each card will pull their configuration for the flash on the NMC when the system is powered down and brought back up. All you should have to do is reboot the chassis, then save all of your modems to their local flash when they come back up. Then you can reboot individual cards or the whole chassis without killing a thing. (choose card, "Configure", "Action Commands", Choose software, the "Save both T1/E1 and modems TO NVRAM") Hope this helps.. Rick Team Solunet -----Original Message----- From: Travis M. Best [mailto:sysadmin@sunqwest.net] Sent: Tuesday, December 03, 2002 9:09 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] Hiper Arc Problems Please Help I have a problem where if I reboot the chassie from the telnet window of do a software reset on the hiper arc it busy out my modems with a fast busy but if I power down the unit and power it backup everything is ok. Has anyone seen this before??? Is this some setting I am missing some where? Please help Thanks, Travis Best Systems Administrator

4 4

If you cant beat the prices, add value. TC1000 v92 bundles
by Stephen Rivera - WRCA.Net 04 Dec '02

04 Dec '02

v92 enabled... Configured as follows: (1) Chassis w/ dual 130Amp AC power supplies. (1) Hiper NMC (2) Hiper ARC 128Mb version (NIC/NAC set) 14) Hiper DSP (T-1 NIC/NAC) $6500.00 per bundle 1 year warranty Perfect Condition!! Technical Support Available. Steve Rivera IM: srivera711 Toll Free: (877)WRCANET x102 DIRECT: 732-833-2034 Fax available equipment to: (732)833-2115 for more product info got www.wrca.net

1 0

WTS: Loaded Hipeer DSP bundles $5500.00
by sky1 04 Dec '02

04 Dec '02

Still have 6 of the Hiper DSP fully loaded bundles that we are looking to unload. Configured as follows: (14) Hiper DSP T-1 V.90 (2) Hiper ARC 128Mb Version (1) Hiper NMC (1) 3Com Chassis w/ dual 130Amp AC power $5500.00 each....would consider offers on quantity of 2 or more of the bundles. Also have a bunch of hiper DSP's and Hiper ARC's (all 128Mb Version) that we need to move. Entertaining offers on quantity. If interested, let me know Shannan Young SouthWest Data Technology, Inc. 972-739-7010 972-739-7013 (Fax) sky1(a)airmail.net www.swdt.com

2 2

replacing PRI with CAS spans?
by Andy 04 Dec '02

04 Dec '02

I'm wondering if anyone has tried configuring HiPer DSP cards for CAS rather than PRI, and what success or failure they have had at it. For more background on CAS spans: http://whatis.techtarget.com/definition/0,,sid9_gci213837,00.html http://www.maxim-ic.com/appnotes.cfm/appnote_number/590 http://www.pulsewan.com/data101/cas.pdf http://www.hut.fi/~ayasmin/PSTN_hw.html http://www.nortelnetworks.com/products/library/collateral/55043.25-07-99.pdf ---

3 3

RE: [USR-TC] Hiper Arc Problems Please Help
by RickL＠solunet.com 04 Dec '02

04 Dec '02

Travis, When you reboot an individual card, the system loads the configuration from the local flash on the card. By contrast, each card will pull their configuration for the flash on the NMC when the system is powered down and brought back up. All you should have to do is reboot the chassis, then save all of your modems to their local flash when they come back up. Then you can reboot individual cards or the whole chassis without killing a thing. (choose card, "Configure", "Action Commands", Choose software, the "Save both T1/E1 and modems TO NVRAM") Hope this helps.. Rick Team Solunet -----Original Message----- From: Travis M. Best [mailto:sysadmin@sunqwest.net] Sent: Tuesday, December 03, 2002 9:09 AM To: usr-tc(a)mailman.xmission.com Subject: [USR-TC] Hiper Arc Problems Please Help I have a problem where if I reboot the chassie from the telnet window of do a software reset on the hiper arc it busy out my modems with a fast busy but if I power down the unit and power it backup everything is ok. Has anyone seen this before??? Is this some setting I am missing some where? Please help Thanks, Travis Best Systems Administrator

2 1

OSPF to RIPv2 Migration
by Joshua Coombs 03 Dec '02

03 Dec '02

After redoing our MPIP setup, verifying NTP (ntp on the nmc's makes them lock after approx 5 hours, theres a new fun fact! : ) ) and ospf confs, we're still having the same issues I noted earlier. So, I want to try RIPv2 as suggested. Having never touched it I've procured a spare chassis, and dropped it into my lab. Any guidelines I should follow setting up the ARC and the cisco it'll be chatting with? Joshua Coombs jcoombs(a)gwi.net

1 0