- USR-TC - mailman.xmission.com

Re: [USR-TC] need help! hiper dsp/pri keeps going to
by matthew＠the-spa.com 08 Apr '03

08 Apr '03

looks like i definitely need to call them first thing tomorrow and have them review the 11th pri and make sure it is identical to the first 10. matthew ---- Original Message ---- From: jcoombs(a)gwi.net To: usr-tc(a)mailman.xmission.com Subject: Re: [USR-TC] need help! hiper dsp/pri keeps going to Date: Tue, 8 Apr 2003 22:03:15 -0400 >Also see if the the telco supports service messaging. We've had >instances where b's would be dropped due to our end having service >messaging enabled, and the remote ignoring it. > >Joshua Coombs > >On Tue, Apr 08, 2003 at 09:58:01PM -0400, Paul Farber wrote: >> Biggest one will be Switch type. >> >> Some switch type are 'close' - 5ESS and NI2 are ones that I had >problems >> with. The switch type was NI2 but my DSPs were at 5ESS... worked >for a >> while but would drop B's, go remote out of service and other >errors. >> >> Verify your line coding and switch type with telco... have them fax >it to >> you if they can so if it changes you can show them. >> >> -- >> Paul Farber >> Farber Technology >> farber(a)admin.f-tech.net >> Ph 570-628-5303 >> Fax 570-628-5545 >> >> On Tue, 8 Apr 2003 matthew(a)the-spa.com wrote: >> >> > >> > i did load all the settings from the first hiper dsp in that >chassis. >> > >> > i have to call the telco tomorrow and have them review all of >their >> > settings just in case that might be it. >> > >> > thanks >> > >> > matthew >> > >> > >> > ---- Original Message ---- >> > From: berto(a)voyager.net >> > To: usr-tc(a)mailman.xmission.com >> > Subject: RE: [USR-TC] need help! hiper dsp/pri keeps going to >"remote >> > out ofservice" after a bunch of calls >> > Date: Tue, 8 Apr 2003 21:43:18 -0400 >> > >> > >Maybe have the telco confirm the new PRI is setup exactly the >same as >> > >the >> > >rest of them....assuming you checked ALL the config settings to >> > >confirm they >> > >are the same. Best bet would be to just load all the settings >from >> > >one of >> > >the other dsps...you can do that from tcm. >> > > >> > >Todd >> > > >> > >-----Original Message----- >> > >From: usr-tc-bounces(a)mailman.xmission.com >> > >[mailto:usr-tc-bounces@mailman.xmission.com]On Behalf Of matthew >> > >Sent: Tuesday, April 08, 2003 9:44 PM >> > >To: usr-tc(a)mailman.xmission.com >> > >Subject: [USR-TC] need help! hiper dsp/pri keeps going to >"remote out >> > >of >> > >service" after a bunch of calls >> > > >> > > >> > >ok here is the situation... >> > > >> > > i have a chassis with 11 hiper dsp's active, dual hiper arc's >and a >> > >hiper >> > >nmc and dual 130's >> > > >> > > i had 10 pri's running fine for the last two months. >> > > >> > > added the 11th pri yesterday. >> > > it seems to run fine for a few hours, fills up with callers >etc. >> > > >> > > then it will get less "busy" than the rest of them, until it >has >> > >nobody >> > >on it. >> > > >> > > when i check it all of the channels are remote out of service. >> > > >> > > if i do a hardware reset it goes back to normal for a few >hours and >> > >then >> > >it does it all over again. >> > > >> > > i have checked all of a the settings and i can't figure out >what is >> > >wrong. >> > > >> > > it seems to be identical to the other 10 pri's/hiper dsp's >> > > >> > > same version etc. >> > > >> > > can someone help me please? >> > > >> > > thanks >> > > >> > > matthew >> > > >> > >matthew de Jongh >> > >president >> > >the spa! internet >> > >voice (413) 539-9818 >> > >www.the-spa.com >> > > >> > > >> > >_______________________________________________ >> > >USR-TC mailing list >> > >USR-TC(a)mailman.xmission.com >> > >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc >> > > >> > > >> > > >> > > >> > >_______________________________________________ >> > >USR-TC mailing list >> > >USR-TC(a)mailman.xmission.com >> > >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc >> > >> > >> > >> > _______________________________________________ >> > USR-TC mailing list >> > USR-TC(a)mailman.xmission.com >> > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc >> > >> >> >> _______________________________________________ >> USR-TC mailing list >> USR-TC(a)mailman.xmission.com >> http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > >_______________________________________________ >USR-TC mailing list >USR-TC(a)mailman.xmission.com >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

RE: [USR-TC] need help! hiper dsp/pri keeps going to
by matthew＠the-spa.com 08 Apr '03

08 Apr '03

all of the pri's are set for 5ess the other 10 work just fine. its just the one new one. matthew ---- Original Message ---- From: farber(a)admin.f-tech.net To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] need help! hiper dsp/pri keeps going to Date: Tue, 8 Apr 2003 21:58:01 -0400 (EDT) >Biggest one will be Switch type. > >Some switch type are 'close' - 5ESS and NI2 are ones that I had >problems >with. The switch type was NI2 but my DSPs were at 5ESS... worked for >a >while but would drop B's, go remote out of service and other errors. > >Verify your line coding and switch type with telco... have them fax >it to >you if they can so if it changes you can show them. > >-- >Paul Farber >Farber Technology >farber(a)admin.f-tech.net >Ph 570-628-5303 >Fax 570-628-5545 > >On Tue, 8 Apr 2003 matthew(a)the-spa.com wrote: > >> >> i did load all the settings from the first hiper dsp in that >chassis. >> >> i have to call the telco tomorrow and have them review all of >their >> settings just in case that might be it. >> >> thanks >> >> matthew >> >> >> ---- Original Message ---- >> From: berto(a)voyager.net >> To: usr-tc(a)mailman.xmission.com >> Subject: RE: [USR-TC] need help! hiper dsp/pri keeps going to >"remote >> out ofservice" after a bunch of calls >> Date: Tue, 8 Apr 2003 21:43:18 -0400 >> >> >Maybe have the telco confirm the new PRI is setup exactly the same >as >> >the >> >rest of them....assuming you checked ALL the config settings to >> >confirm they >> >are the same. Best bet would be to just load all the settings from >> >one of >> >the other dsps...you can do that from tcm. >> > >> >Todd >> > >> >-----Original Message----- >> >From: usr-tc-bounces(a)mailman.xmission.com >> >[mailto:usr-tc-bounces@mailman.xmission.com]On Behalf Of matthew >> >Sent: Tuesday, April 08, 2003 9:44 PM >> >To: usr-tc(a)mailman.xmission.com >> >Subject: [USR-TC] need help! hiper dsp/pri keeps going to "remote >out >> >of >> >service" after a bunch of calls >> > >> > >> >ok here is the situation... >> > >> > i have a chassis with 11 hiper dsp's active, dual hiper arc's >and a >> >hiper >> >nmc and dual 130's >> > >> > i had 10 pri's running fine for the last two months. >> > >> > added the 11th pri yesterday. >> > it seems to run fine for a few hours, fills up with callers etc. >> > >> > then it will get less "busy" than the rest of them, until it has >> >nobody >> >on it. >> > >> > when i check it all of the channels are remote out of service. >> > >> > if i do a hardware reset it goes back to normal for a few hours >and >> >then >> >it does it all over again. >> > >> > i have checked all of a the settings and i can't figure out what >is >> >wrong. >> > >> > it seems to be identical to the other 10 pri's/hiper dsp's >> > >> > same version etc. >> > >> > can someone help me please? >> > >> > thanks >> > >> > matthew >> > >> >matthew de Jongh >> >president >> >the spa! internet >> >voice (413) 539-9818 >> >www.the-spa.com >> > >> > >> >_______________________________________________ >> >USR-TC mailing list >> >USR-TC(a)mailman.xmission.com >> >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc >> > >> > >> > >> > >> >_______________________________________________ >> >USR-TC mailing list >> >USR-TC(a)mailman.xmission.com >> >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc >> >> >> >> _______________________________________________ >> USR-TC mailing list >> USR-TC(a)mailman.xmission.com >> http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc >> > > >_______________________________________________ >USR-TC mailing list >USR-TC(a)mailman.xmission.com >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

RE: [USR-TC] need help! hiper dsp/pri keeps going to
by matthew＠the-spa.com 08 Apr '03

08 Apr '03

i did load all the settings from the first hiper dsp in that chassis. i have to call the telco tomorrow and have them review all of their settings just in case that might be it. thanks matthew ---- Original Message ---- From: berto(a)voyager.net To: usr-tc(a)mailman.xmission.com Subject: RE: [USR-TC] need help! hiper dsp/pri keeps going to "remote out ofservice" after a bunch of calls Date: Tue, 8 Apr 2003 21:43:18 -0400 >Maybe have the telco confirm the new PRI is setup exactly the same as >the >rest of them....assuming you checked ALL the config settings to >confirm they >are the same. Best bet would be to just load all the settings from >one of >the other dsps...you can do that from tcm. > >Todd > >-----Original Message----- >From: usr-tc-bounces(a)mailman.xmission.com >[mailto:usr-tc-bounces@mailman.xmission.com]On Behalf Of matthew >Sent: Tuesday, April 08, 2003 9:44 PM >To: usr-tc(a)mailman.xmission.com >Subject: [USR-TC] need help! hiper dsp/pri keeps going to "remote out >of >service" after a bunch of calls > > >ok here is the situation... > > i have a chassis with 11 hiper dsp's active, dual hiper arc's and a >hiper >nmc and dual 130's > > i had 10 pri's running fine for the last two months. > > added the 11th pri yesterday. > it seems to run fine for a few hours, fills up with callers etc. > > then it will get less "busy" than the rest of them, until it has >nobody >on it. > > when i check it all of the channels are remote out of service. > > if i do a hardware reset it goes back to normal for a few hours and >then >it does it all over again. > > i have checked all of a the settings and i can't figure out what is >wrong. > > it seems to be identical to the other 10 pri's/hiper dsp's > > same version etc. > > can someone help me please? > > thanks > > matthew > >matthew de Jongh >president >the spa! internet >voice (413) 539-9818 >www.the-spa.com > > >_______________________________________________ >USR-TC mailing list >USR-TC(a)mailman.xmission.com >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > > > > >_______________________________________________ >USR-TC mailing list >USR-TC(a)mailman.xmission.com >http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

3 2

PSU question
by alex＠wanex.ge 08 Apr '03

08 Apr '03

This chassis is connected to 2 UPS-s in case of 1 fails another will work. What will happen if voltage (or amperage or freq.) of one UPS is different from another?

4 3

RE: [USR-TC] v90 enable string
by Joel - Fox Computers 08 Apr '03

08 Apr '03

I believe in those old units, the NMC is what determines if V.90 is enabled(?). If so, I know you can purchase old V.90-enabled NMC's for those for not much money. Look on EBay or email me off list if you can't find one. I have a 486 NMC here that is V.90 enabled, and I THINK that's all you need. - Joel -----Original Message----- From: Wayne Barber [mailto:barberw@tidewater.net] Sent: Tuesday, April 08, 2003 10:58 AM To: usr-tc(a)mailman.xmission.com Cc: rede1(a)linkway.com.br Subject: Re: [USR-TC] v90 enable string Hi, your English is much better than my any other language. The equipment you purchased has long been discontinued by 3Com. When they originally came out with v.90, you needed to purchase the enable string from them. You probably need to contact 3Com to see if it's still available. At this time, they *should* be giving it away, but they don't normally work that way. Good luck. On 8 Apr 2003 at 12:10, Marcelo Tadeu Mirabelli March wrote: > > Hi guys! > > First of all, excuse me about my fuzzy english. > > I've just purchased a used T1000 chassis, with several quad modems, a > dual-pri, a netserver card and a nmc card. > > The chassis is fine, is working well, only does not accept conections > over 33k6. The v90 enable string is missing. > > I've already tried to contact the local dealer, but they tell me that my > chassis is too old and they aren't able to sell me one. Funny, isn't it? > I purchased the chassis from them one week ago! > > Have anyone a solution for my case? > > Where I can obtain the v90 enabling string? > > Thanks in advance. > > -- > [.........]s > Marcelo Marchesoni > rede1(a)linkway.com > Sao Carlos - SP - Brasil > > -- > Essa mensagem foi verificada contra vírus e > conteúdo malicioso. > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc > Wayne Barber Coastal Telco Services _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

v90 enable string
by Marcelo Tadeu Mirabelli Marchesoni 08 Apr '03

08 Apr '03

Hi guys! First of all, excuse me about my fuzzy english. I've just purchased a used T1000 chassis, with several quad modems, a dual-pri, a netserver card and a nmc card. The chassis is fine, is working well, only does not accept conections over 33k6. The v90 enable string is missing. I've already tried to contact the local dealer, but they tell me that my chassis is too old and they aren't able to sell me one. Funny, isn't it? I purchased the chassis from them one week ago! Have anyone a solution for my case? Where I can obtain the v90 enabling string? Thanks in advance. -- [.........]s Marcelo Marchesoni rede1(a)linkway.com Sao Carlos - SP - Brasil -- Essa mensagem foi verificada contra vírus e conteúdo malicioso.

2 1

What is a 003446-0
by Paul Farber 07 Apr '03

07 Apr '03

I have to send back some leased 3COM gear, a double play upgrade from 1999. Its was 2 DSPs, a PS, and an NMC upgrade. Problem is it can't remember what was upgraded in the NMC.. the FLASH or RAM. ANyone remember which it is? My best guess is that is was a 16MB Flash upgrade up from the standard 8MB flash that came with the NMC cards. -- Paul Farber Farber Technology farber(a)admin.f-tech.net Ph 570-628-5303 Fax 570-628-5545

1 0

RE: [USR-TC] PSU question
by Joel - Fox Computers 07 Apr '03

07 Apr '03

One thing you have to make sure is that your power supplies are the same type. A person can have two 130A AC power supplies, but if you have one Type 8 power supply and one Type 4 power supply (something I've tried) you will see the exact behavior you describe - power one off and the entire rack goes down momentarily and everything restarts. My experience has been that as long as your two power supplies are exactly identical, the failover works perfectly. I've had several occasions (last night, in fact, while switching out the UPS) where I have to power one or the other off, never disconnect a user while doing it. - Joel -----Original Message----- From: Joshua Coombs [mailto:jcoombs@gwi.net] Sent: Monday, April 07, 2003 9:38 AM To: Discussion relating to the 3Com/US Robotics Total Control modem systems.; alex(a)wanex.ge Subject: Re: [USR-TC] PSU question As long as both UPSs are running within normal tolerances, fail over should work as expected. Note I have observed powersupply fail over tripping over itself in the past using 130A 120v powersupplies on dual feeds. Both power supplies were green, power down one and the chassis rebooted... so your milage may vary. Sometimes it works, sometimes it doesn't, even if they are on the same power source. Joshua Coombs On Monday 07 April 2003 08:32 am, alex(a)wanex.ge wrote: > This chassis is connected to 2 UPS-s in case of 1 fails another will > work. What will happen if voltage (or amperage or freq.) of one UPS is > different from another? > > > > > _______________________________________________ > USR-TC mailing list > USR-TC(a)mailman.xmission.com > http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc _______________________________________________ USR-TC mailing list USR-TC(a)mailman.xmission.com http://mailman.xmission.com/cgi-bin/mailman/listinfo/usr-tc

1 0

Hiper Chassis Blowout!!!
by sky1 07 Apr '03

07 Apr '03

Got more Hiper Chassis to move!!! Pricing breakdown: Quantity (1) $3750.00 Quantity of (2-3) $3500.00 ea Quantity of 4-10 $3250.00 ea Fully loaded Hiper Chassis Configured as follows: (14) Hiper DSP T-1 Card Sets (2) Hiper ARC 128 Mb Version (1) Hiper NMC (2) 130 Amp AC power supplies (1) "Blue" Labeled chassis w/ integrated Fan tray Hiper DSP Cards $175.00 each Hiper ARC Sets (128 MB Version) $125.00 each All equipment in excellent condition....6 month warranty. If interested, contact: Shannan Young SouthWest Data Technology, Inc. 972-739-7010 972-739-7013 (Fax) sky1(a)airmail.net www.swdt.com

1 0

Frozen Console
by Rogerio Carvalho 05 Apr '03

05 Apr '03

Hi all I have a Total Control Enterprise Network Hub, when i try to start a console in NMC or in the NetServer the first message apears like that menu of NMC but after that the console frozen and i cant do nothing, i tried all ways to fix that like change speed, dip switches, cables but nothing happens, if someon could help me... []'s --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com) Version: 6.0.467 / Virus Database: 266 - Release Date: 01/04/03

2 1